bondura 3.3 Ø25mm - Ø200mm assembly & inspection manual art rev A
|
|
- Oddbjørn Snorre Iversen
- 6 år siden
- Visninger:
Transkript
1 bondura 3.3 Ø25mm - Ø200mm assembly & inspection manual art rev A
2 TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment 3/ inspection inspeksjon 4/ disassembly demontering positioning detail posisjoneringsdetalj nut mutter grease nipple smørenippel seeger ring seeger ring conical sleeve konhylse o-ring o-ring pin pin support innfestning bearing lager 1
3 1/ assembly montering 1.1/ Preparing for installation by centering and cleaning the pin bore. Do not force the pin into a bore that is not properly aligned, this may damage both the pin and bearing. Klargjøring for montering ved å sentrere og rengjøre pin-hullet. Dersom pin presses inn i et hull som ikke er sentrert, kan både pin og lager skades. 1.2/ Prepare the bondura assembly by removing the conical sleeve/nut assembly and seeger ring. Klargjør bondura sammenstillingen ved å demontere konhylse/ mutter sammenstillingen og seeger ringen. Important! The following friction surfaces must always be clean, dry and free of any oil and grease substances when installing the bondura assembly: Contact surfaces between tapered end of bondura pin and adjacent inner part of conical sleeve. Contact surfaces between outer part of conical sleeve and adjacent bore in support. Viktig! Følgende friksjonsflater må alltid være rene, tørre og fri for olje- og fettstoffer når en bondura sammenstilling blir innstallert: Kontaktflater mellom konisk ende på bondura pin og tilstøtende indre del av bondura konhylse. Kontaktflater mellom utsiden av bondura konhylse og tilstøtende hull i innfestning. 1.3/ Insert the pin. The end surface of the pin must be flush with the support. The pin needs to be centered. If the pin is not aligned correctly with the support, the bondura assembly may not function correctly. Sett inn pin. Endeflaten skal ligge jevnt med yttersiden av innfestningen. Pin må være sentrert. Dersom endeflaten ikke ligger jevnt med yttersiden på innfestningen kan dette hindre funksjonen til bondura sammenstillingen. 2
4 1.4/ Assemble the components. Make sure that the positioning detail fits to the surface of the tapered end. Komponenter monteres. Pass på at posisjoneringsdetaljen passer til flaten på den koniske enden. 1.5/ Tighten alternately at both ends. Tighten to the specified torque. See technical specifications/torque. Trekk til vekselvis i begge ender. Trekk til oppgitt moment. Se tekniske data/tiltrekkingsmoment. 1.6/ The bondura assembly locks to the support as the conical sleeves expand and create a wedge-force between pin and support, and thus prevent rotation and sliding sideways. bondura sammenstillingen låses mot rotasjon og utglidning ved at konhylsene ekspanderer og skaper kilkraft mellom pin og innfestning. 1.7/ The conical sleeves expand and absorb up to 2mm (0,08 ) gap/wear between the pin and support. For larger clearances, oversize conical sleeves must be used. Oversize conical sleeves will be used in cases of more than 2mm clearance due to wear, or as a replacement for a worn bushing. Konhylsene ekspanderer og absorberer inntil 2mm klaring/slark mellom pin og innfestning. Ved større klaring må overmål konhylse benyttes. Overmål konhylser brukes hvor det er mer enn 2mm klaring på grunn av slitasje eller som erstatning for utslitt foringshylse. Oversize conical sleeve Overmål konhylse 3 Standard conical sleeve Standard konhylse
5 1.8/ The conical sleeves repair up to 1mm (0,04 ) ovality. In case of more than 1mm ovality the oval hole should be grinded rounder before installation of the bondura assembly. Konhylsene reparerer inntil 1mm ovalitet. Ved mer enn 1mm ovalitet bør det ovale hullet slipes rundere før bondura sammenstillingen monteres. 1.9/ It is the tightening regime of the nuts, with subsequent conical sleeve expansion, that allows the bondura assembly to repair ovality in the support. Retightening of the nuts will be necessary during a period; until desired torque value is achieved. Det er tilstrammingen av mutre med påfølgende konhylse ekspansjon som gjør at bondura sammenstillingen reparerer slark i innfestningen. Ettertrekking av mutre må utføres i en innkjøringsperiode inntil ønsket moment er oppnådd. 1.10/ If the bondura pin has a lubrication channel/grease nipple; lubricate the bearing to OEM s recommendation. Single or double lubrication groove from dia 114 -> Dersom bondura pin har smørekanal/smørenippel smøres lager etter utstyrsprodusentens anbefaling. Enkelt eller dobbelt smørespor fra Ø114 -> 2/ technical specifications/torque tekniske data/tiltrekkingsmoment Diameter mm Torque Moment Nut Mutter Wrench size Nøkkelvidde Ø Nm Ø Nm M18 30 Ø Nm M24 41 Ø Nm M36 55 Ø Nm M42 60 Ø Nm Ø Nm M56 75 Ø Nm M Ø Nm Ø M All torque values in dry state. For lubricated threads reduce the torque values by 10%. Alle moment verdier i tørr tilstand. For smurte gjenger reduseres moment verdiene med 10%. 4
6 3/ inspection inspeksjon bondura technology recommends the customer/user to implement a maintenance program to check the bondura assembly along with the specified service intervals for the relevant equipment. It is important to control and ensure the expanding forces between conical sleeve and support, and retighten the nuts if needed. bondura technology anbefaler kunde/bruker å implementere vedlikehold av bondura sammenstillingen i vedlikeholdsprogrammet for aktuelt utstyr. Det er viktig å kontrollere og sikre ekspansjonskrefter mellom konhylse og innfestning, og eventuelt ettertrekke mutrene. 3.1/ Inspect Distance Indicator-X Value < 2mm can be an indication of the following: a) The bondura assembly has shifted sideways. See installation section 1.3. b) There is a need for an oversize conical sleeve. See section 1.7. Kontroller indikatoravstand-x Verdi < 2mm kan være en indikasjon på følgende: a) bondura sammenstillingen har forskjøvet seg sideveis. Se montering punkt 1.3. b) Det er behov for overmåls konhylse. Se punkt / Inspect if the nuts are loose, broken or missing. a) Check that the torque is as specified in the technical specifications/torque. b) Install new nuts if nuts are missing. Kontroller om mutre er løse, brukket eller mangler. a) Kontroller at tiltrekkingsmoment er som oppgitt i teknisk data/tiltrekkingsmoment. b) Monter nye mutre dersom mutre mangler. 4/ disassembly demontering Loosen the nut assembly, and pull out the bondura pin. Løsne muttersammenstillingen, og trekk ut bondura pin. 5
7 bondura technology AS Vardheivegen 56b 4340 Bryne Norway support tel
bondura dual 36 Ø50mm - Ø200mm assembly & inspection manual art rev A
bondura dual 36 Ø50mm - Ø200mm assembly & inspection manual art. 103803 rev. 27.04.2016 A TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 3.3 Ø10mm - Ø200mm assembly & inspection manual art rev C
bondura 3.3 Ø10mm - Ø200mm assembly & inspection manual art. 103802 rev. 14.03.2018 C TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.1 Ø100mm - Ø195mm assembly & inspection manual art rev A
bondura 6.1 Ø100mm - Ø195mm assembly & inspection manual art. 103797 rev. 02.02.2016 A TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.6 Ø25mm - Ø65mm assembly & inspection manual art rev A
bondura 6.6 Ø25mm - Ø65mm assembly & inspection manual art. 103800 rev. 25.01.2016 A TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura dual 66 Ø75mm - Ø360mm assembly & inspection manual art rev A
bondura dual 66 Ø75mm - Ø360mm assembly & inspection manual art. 103804 rev. 25.01.2016 A TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.2 Ø25mm - Ø69mm assembly & inspection manual art rev C
bondura 6.2 Ø25mm - Ø69mm assembly & inspection manual art. 106105 rev. 14.03.2018 C TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.6 Ø25mm - Ø69mm assembly & inspection manual art rev C
bondura 6.6 Ø25mm - Ø69mm assembly & inspection manual art. 103800 rev. 14.03.2018 C TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.2 Ø50mm - Ø500mm assembly & inspection manual art rev C
bondura 6.2 Ø50mm - Ø500mm assembly & inspection manual art. 103798 rev. 14.03.2018 C TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.6 Ø20mm - Ø65mm assembly & inspection manual
bondura 6.6 Ø20mm - Ø65mm assembly & inspection manual TABLE OF CONTENT / INNHOLDSFORTEGNELSE 1/ assembly in new equipment montering i nytt utstyr 2/ assembly in equipment with wear and ovality montering
Detaljerbondura 6.6 Ø50mm - Ø500mm assembly & inspection manual art rev C
bondura 6.6 Ø50mm - Ø500mm assembly & inspection manual art. 103801 rev. 14.03.2018 C TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.1 Ø200mm - Ø500mm assembly & inspection manual art rev B
bondura 6.1 Ø200mm - Ø500mm assembly & inspection manual art. 104194 rev. 04.04.2018 B TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.1 Ø100mm - Ø200mm assembly & inspection manual art rev B
bondura 6.1 Ø100mm - Ø200mm assembly & inspection manual art. 103797 rev. 04.04.2018 B TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.1 Ø30mm - Ø99mm assembly & inspection manual art rev C
bondura 6.1 Ø30mm - Ø99mm assembly & inspection manual art. 106104 rev. 14.03.2018 C TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura 6.6 Ø55mm - Ø500mm assembly & inspection manual
bondura 6.6 Ø55mm - Ø500mm assembly & inspection manual TABLE OF CONTENT / INNHOLD 1/ assembly in new equipment montering i nytt utstyr 2/ assembly in equipment with wear and ovality montering i utstyr
Detaljerbondura Dual 66 Ø75mm - Ø360mm assembly & inspection manual art rev C
bondura Dual 66 Ø75mm - Ø360mm assembly & inspection manual art. 103804 rev. 20.04.2018 C TABLE OF CONTENT / INNHOLD 1/ assembly montering 2/ technical specifications/torque tekniske data/tiltrekkingsmoment
Detaljerbondura Multi Tool 200 Hydraulic Ø200mm - Ø320mm user manual - for disassembly
bondura Multi Tool 200 Hydraulic Ø200mm - Ø320mm user manual - for disassembly 1/ cone sleeve removal demontering av konhylse 2/ pin removal demontering av bolt 3/ additional Ø140mm - Ø195mm tillegg for
Detaljerbondura Multi Tool 200
bondura Multi Tool 200 pin and conical sleeve removal Ø200mm - Ø320mm user manual - for disassembly art. 103807 rev. 16.03.2016 A 1/ bondura 6.6 1.1 conical sleeve removal / demontering av konhylse 1.2
DetaljerKAMPANJE APK : APK-8: Bytte bakaksel bolter
KAMPANJE APK-8 20160222: APK-8: Bytte bakaksel bolter Berørte modeller for APK-8: Vitara APK, S-cross AKK, og Swift AZG. Totalt 454 biler på det norske markedet. Liste med chassisnummer legges ikke ved,
DetaljerJusteringsanvisninger finnes på de to siste sidene.
d Montering av popup spredere Justeringsanvisninger finnes på de to siste sidene. Link til monteringsfilm på youtube: http://youtu.be/bjamctz_kx4 Hver spreder har montert på en "svinkobling", det vil si
DetaljerReplacing the tube and/or tyre of a drive wheel, indoor/outdoor
ASSEMBLY INSTRUCTION Replacing the tube and/or tyre of a drive wheel, indoor/outdoor EN NO 9010182A 5.2.7 9010182 Replacing the tube and/or tyre of a drive wheel, indoor/outdoor Preparation Be sure that
DetaljerINSTALLATION GUIDE FTR Cargo Rack Regular Ford Transit 130" Wheelbase ( Aluminum )
INSTALLATION GUIDE 1505-FTR Cargo Rack Regular Ford Transit 130" Wheelbase ( Aluminum ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Cargo Rack Assembly... 3-4 5-6 Phase 2 - Installation q
DetaljerINSTALLATION GUIDE FTR Cargo Rack Regular Ford Transit 130" Wheelbase ( Aluminum )
INSTALLATION GUIDE 1505-FTR Cargo Rack Regular Ford Transit 130" Wheelbase ( Aluminum ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Cargo Rack Assembly... 3-4 5-6 Phase 2 - Installation q
DetaljerMonteringsanvisning. Assembly instructions. Ledsagerbrems / Drum brake. Artikkelnummer/ Item no.
Monteringsanvisning Assembly instructions Exigo 30 Emineo Ledsagerbrems / Drum brake Beskrivelse/Description 20 Flexel/Compact 84417 20 Luft/Pneumatic 84416 20 Pur 84419 22 Flexel/Compact 84437 22 Luft/Pneumatic
DetaljerREMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION
2011-2014 FORD EXPLORER PARTS LIST Qty Part Description Qty Part Description 1 Bull Bar 2 12mm x 35mm Bolt Plates 1 Passenger/Right Mounting Bracket 2 12mm Nut Plate 1 Driver/Left Mounting Bracket 2 12mm
DetaljerKAMPANJE APK : APK-5: Skifte pakninger mellom turbo og CCDPF
KAMPANJE APK-5 20150722: APK-5: Skifte pakninger mellom turbo og CCDPF Berørte modeller for APK-5: Vitara APK416D, totalt 66 biler. Liste med chassisnummer legges ikke ved, bruk Forhandlerweb til å sjekke
DetaljerMAINTENANCE INSTRUCTION FOR RELEASE HOOK
Supplier: Document title: MAINTENANCE INSTRUCTION FOR RELEASE HOOK Supplier Doc. No.: M01-003 Number of page: 1 of 6 Rev. No.: 02 File name: J:\STANDARD\M01-003 P.O.No.: Client: Client Doc.no.: Tag no./type:
DetaljerReplacing the carbon brushes
ASSEMBLY INSTRUCTION Replacing the carbon brushes EN NO 9010180A 5.2.4 9010180 Replacing the carbon brushes (Puma 20/40) Preparation Switch off the wheelchair via the remote control. Be sure that the
DetaljerTRANSFER CASE Mitsubishi Montero APPLICATION DESCRIPTION TESTING 4WD INDICATOR CONTROL UNIT (MONTERO) DETECTION SWITCH
TRANSFER CASE 1991 Mitsubishi Montero 1991-94 TRANSFER CASES Mitsubishi Dodge; Ram-50 Mitsubishi; Pickup, Montero APPLICATION TRANSFER CASE APPLICATIONS TABLE Application (1) Transmission Model Dodge 1991-93
DetaljerIMPORTANT! HOLD ON THIS DOCUMENT FOR LATER REFERENCE! READ CAREFULLY! VIKTIG! BEHOLD DETTE DOKUMENTET FOR FREMTIDIG BRUK! LES NØYE IGJENNOM!
GB IMPORTANT! HOLD ON THIS DOCUMENT FOR LATER REFERENCE! READ CAREFULLY! NOR VIKTIG! BEHOLD DETTE DOKUMENTET FOR FREMTIDIG BRUK! LES NØYE IGJENNOM! Produktmål, materiale: 135x77x72 cm Furu Proper use This
DetaljerKAMPANJE AZG : Skifte bolter reimhjul
KAMPANJE AZG-4 20141009: Skifte bolter reimhjul Berørte modeller: Swift AZG type 3 (produsert i Ungarn) fra 2013 og nyere. (Type 3: Biler med automatisk kjørelys og navigasjon). Kampanjen omfatter totalt
DetaljerStart Here USB *CC * *CC * USB USB
1 USB Start Here USB 11 USB WARNING: To ensure that the software is installed correctly, do not connect the USB cable until step 11. 11 USB 2 a. b. Lower both the paper tray and the print cartridge door.
DetaljerReplacing the batteries
ASSEMBLY INSTRUCTION Replacing the batteries EN NO 9010189A 5.2.14 9010189 Replacing the batteries Preparation Switch off the wheelchair via the remote control. Remove the fuses from the battery compartment
DetaljerCylindrical roller bearings
Cylindrical roller bearings Cylindrical roller bearings 292 Definition and capabilities 292 Series 292 Variants 293 Tolerances and clearances 294 Design criteria 296 Installation/assembly criteria 297
DetaljerUnit Relational Algebra 1 1. Relational Algebra 1. Unit 3.3
Relational Algebra 1 Unit 3.3 Unit 3.3 - Relational Algebra 1 1 Relational Algebra Relational Algebra is : the formal description of how a relational database operates the mathematics which underpin SQL
DetaljerMonteringsprosedyre for Soundstop - lydmatte
NORSOK STANDARD PIPING AND EQUIPMENT INSULATION R-004 5.7 Guidelines for acoustic insulation The acoustic pipe insulation classes can be met by various combinations of insulation materials and jacketing
DetaljerMontering av Lian Skyvedør Installation of Lian Sliding Door
Montering av Lian Skyvedør Installation of Lian Sliding Door Les dette før du starter monteringen! Read these instructions carefully before installation. Sjekk nøye at produktet stemmer med bestilling
Detaljer- Vennlig hilsen gründerne bak retyre
Etter to år med utvikling og testing er retyre endelig klar for å møte den norske vinteren. Det begynte med en idé om en enkel sykkelkjetting, og endte opp med verdens første modulære sykkeldekk. Vi håper
Detaljer60-162-300. Monteringsanvisning Assembly Instructions Monteringsanvisning. Søve Lekemiljø AS 3830 Ulefoss - Norway Tlf: +47 35 94 65 65 www.sove.
UK Monteringsanvisning Assembly Instructions Monteringsanvisning Produkt nr. / Product no. / Produkt nr. 60-162-300 Ordr. nr. Dato. Sign. Søve Lekemiljø AS 3830 Ulefoss - Norway Tlf: +7 35 9 65 65 www.sove.no
DetaljerIndependent Inspection
Independent Inspection Odd Ivar Johnsen Vidar Nystad Independent Inspection Mål: Felles forståelse og utøvelse av "Independent Inspection" i forbindelse med "Critical Maintenance Task". Independent Inspection
DetaljerMONTASJEBESKRIVELSE INSTALLATION GUIDE
MONTASJEBESKRIVELSE INSTALLATION GUIDE ADVARSEL WARNINGS Dette armaturet er et Klasse II produkt som IKKE SKAL TILKOBLES JORD. This device is a class II product: DO NOT CONNECT THE LAMP and the pole to
DetaljerRoma Garden Art.no: FP-ROMGR-100 Last updated: 12.07.13
NOMonteringsanvisning 2 GB Assembly instructions 3 Roma Garden Art.no: FP-ROMGR-100 Last updated: 12.07.13 Roma Garden Vekt Krav til gulvplate 352 kg 670 mm Ta kontakt med en faghandler om du trenger tips
DetaljerSlope-Intercept Formula
LESSON 7 Slope Intercept Formula LESSON 7 Slope-Intercept Formula Here are two new words that describe lines slope and intercept. The slope is given by m (a mountain has slope and starts with m), and intercept
DetaljerMidnight BBQ Light USER MANUAL
Midnight BBQ Light USER MANUAL Instructions The Midnight BBQ Light uses 4 x LR44 / AG13 batteries, included in the package. Unscrew the bottom cover and insert the included batteries and align the battery
DetaljerMerak Un-glazed Porcelain Wall and Floor Tiles
6 Colours 3 es Absolute Collection 7 s Merak Un-glazed Porcelain Wall and Floor Tiles Merak includes seven sizes perfectly designed for seamless installation. 600 x 50mm 600 x 100mm 600 x 300mm 600 x 150mm
DetaljerSERVICE BULLETINE 2008-4
S e r v i c e b u l l e t i n e M a t e r i e l l Materiellsjef F/NLF kommuniserer påminnelse omkring forhold som ansees som vesentlige for å orientere om viktige materiellforhold. Målgruppen for Servicbulletinen
DetaljerInstruksjons manual Instruction manual
knm Copyright c - 2011 knm Side. 1 BRUK AV UTSTYRET Utstyret er designet for løft, trekk, folding/bøying, kutting, støtteoperasjoner etc, og krever, med sitt høye operasjonstrykk og tunge arbeids last,
DetaljerMonteringsanvisning Installation manual Taksokkel for LHH og CareLite Ceiling mount for LHH and CareLite
Monteringsanvisning Installation manual Taksokkel for LHH og CareLite Ceiling mount for LHH and CareLite Art.nr. 05-900-573-00. Page 1 of 9 Norsk Monteringsanvisning taksokkel Denne monteringsmanualen
DetaljerSafeRing / SafePlus Retrofit of under voltage coil V Module
SafeRing / SafePlus Retrofit of under voltage coil V Module Installation Instructions www.abb.com Document status Responsible RELEASED NODIS Location Date Name Prepared NODIS 2008-12-15 BJGU/GUSO Checked
DetaljerTrigonometric Substitution
Trigonometric Substitution Alvin Lin Calculus II: August 06 - December 06 Trigonometric Substitution sin 4 (x) cos (x) dx When you have a product of sin and cos of different powers, you have three different
DetaljerCylindrical roller bearings
Cylindrical roller bearings Cylindrical roller bearings 292 Definition and capabilities 292 Series 292 Variants 293 Tolerances and clearances 294 Design criteria 296 Installation/assembly criteria 297
DetaljerGIMOTA AG. Assembly Instructions Dataconnectors D-SUB. Datenstecker Katalog Gimota AG 04/14 3
GIMOTA AG Assembly Instructions Dataconnectors D-SUB 2015 Datenstecker Katalog Gimota AG 04/14 3 1 Assembly Instructions D-SUB TRAC / TRAC H 1.1 Preparation Standard Part sets Standard part sets conclude
DetaljerMarmi Plus One. Sleek, Essential, Stunning
MARMI PLUS ONE Marmi Plus One Sleek, Essential, Stunning Marmi Plus One Bianco - DME01 90x90 cm Marmi Plus One Bianco - DME01 60x120 cm Marmi Plus One Bianco MATTE Marmi Plus One Bianco - DME01 60x120
DetaljerExercise 1: Phase Splitter DC Operation
Exercise 1: DC Operation When you have completed this exercise, you will be able to measure dc operating voltages and currents by using a typical transistor phase splitter circuit. You will verify your
DetaljerLIFT PROGRAMME SLIDING GUIDES 10/2015
2 SLIDING GUIDES 1! B C D E F @ G H I J K L M N J O O I P M J Q N R S M T U V E W @ " #!! " $ % & ' < = > >? @ A A ' 9 : ; ; 4 4 0 3 1 0 /. - ) * +,, ) * +,, 8 8 7 6 5 ) * +,, ( ( ( ( X ( ( 5 Guide holders
Detaljer#89853 Command Center
1 #89853 Command Center Portable AV Center Assembly Instructions #89853 Command Center Portable AV Center Part rawing escription Qty Part rawing escription Qty Hardware List A Socket Screw M6X9mm 16 A
DetaljerPSi Apollo. Technical Presentation
PSi Apollo Spreader Control & Mapping System Technical Presentation Part 1 System Architecture PSi Apollo System Architecture PSi Customer label On/Off switch Integral SD card reader/writer MENU key Typical
DetaljerKAMPANJE AZG : Skifte bakre bremsecalipere
KAMPANJE AZG-5 06058: Skifte bakre bremsecalipere Berørte modeller: Swift AZG produsert i Ungarn fra 0.09.04 til..05. Totalt 656 biler Eierne kontaktes pr. brev fra Teknisk avdeling. NB! Ikke alle bilene
DetaljerHandicare Emineo Ledsagerbrems Basic / Drum brake Basic
Monteringsanvisning Assembly instructions Handicare Emineo Ledsagerbrems Basic / Drum brake Basic Beskrivelse/Description Art. nr / Item no. 20 Flexel/Compact 84417 20 Luft/Pneumatic 84416 22 Flexel/Compact
DetaljerHONSEL process monitoring
6 DMSD has stood for process monitoring in fastening technology for more than 25 years. HONSEL re- rivet processing back in 990. DMSD 2G has been continuously improved and optimised since this time. All
DetaljerDynamic Programming Longest Common Subsequence. Class 27
Dynamic Programming Longest Common Subsequence Class 27 Protein a protein is a complex molecule composed of long single-strand chains of amino acid molecules there are 20 amino acids that make up proteins
DetaljerWindlass Control Panel
SIDE-POWER 86-08955 Windlass Control Panel v1.0.2 Windlass Systems Installasjon manual SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: +47 69 30 00 60 Fax: +47 69 30 00 70 w w w. s i d e
DetaljerInformation search for the research protocol in IIC/IID
Information search for the research protocol in IIC/IID 1 Medical Library, 2013 Library services for students working with the research protocol and thesis (hovedoppgaven) Open library courses: http://www.ntnu.no/ub/fagside/medisin/medbiblkurs
DetaljerFitting instruction. devi-pipeheat / devi-flexheat Assembly between cold tail and selflimiting. Montering av tilledning på selvbegrensende varmekabel
GB/NO Fitting instruction devi-pipeheat / devi-flexheat Assembly between cold tail and selflimiting heating cable Item no. 19806415 Montering av tilledning på selvbegrensende varmekabel Art. nr. 19806415
DetaljerSafeRing / SafePlus Retrofit of auxiliary switch S9 for fuse blown indication F module
SafeRing / SafePlus Retrofit of auxiliary switch S9 for fuse blown indication F module Installation instructions www.abb.com Document status Responsible RELEASED NODIS Location Date Name Prepared NODIS
DetaljerALUMINUM TWIN STACK PORTABLE AIR COMPRESSOR OL50135AL OPERATOR S MANUAL
OL50135AL OPERATOR S MANUAL ALUMINUM TWIN STACK PORTABLE AIR COMPRESSOR! WARNING: To reduce the risk of injury, the user must read and understand the Operator s Manual before using this product. IN619302AV
DetaljerDu vil trenge: Umbraco Nøkkel (Inkludert); Skiftnøkkel/Fastnøkkel sett (For styrestem bolten og de 4 styreboltene),pumpe
Pawtrekker DOG SCOOTERS / SPARKSYKKEL Monteringsanvisning Du vil trenge: Umbraco Nøkkel (Inkludert); Skiftnøkkel/Fastnøkkel sett (For styrestem bolten og de 4 styreboltene),pumpe Vi anbefaler å montere
DetaljerSafeRing / SafePlus Retrofit of auxiliary switch S9 for relay trip indication V module
SafeRing / SafePlus Retrofit of auxiliary switch S9 for relay trip indication V module Installation instructions www.abb.com Document status Responsible RELEASED NODIS Location Date Name Prepared NODIS
DetaljerThe regulation requires that everyone at NTNU shall have fire drills and fire prevention courses.
1 The law The regulation requires that everyone at NTNU shall have fire drills and fire prevention courses. 2. 3 Make your self familiar with: Evacuation routes Manual fire alarms Location of fire extinguishers
DetaljerNEOREST Hybrid (Toilet bowl) NEOREST Hybrid. Installation manual. Safety Cautions Precaution before installation. Included parts.
Installation manual NEOREST Hybrid (Toilet bowl) NEOREST Hybrid Safety Cautions Precaution before installation Included parts Part diagram Installation procedure EN Install the product properly according
DetaljerKAMPANJE AZH : Skifte av støvdeksel
KAMPANJE AZH-4 0404: Skifte av støvdeksel Berørte modeller: Swift AZH type (produsert i Japan) fra 00 til 03. Kampanjen omfatter totalt 334 biler med chassisnummer mellom JSAFZD7S0000030 og JSAFZD7S0036004.
DetaljerInnhold. Instruks for melding av hærverk. ID1743-a- hærverk. IE76286-b- Trafikkdetektor Leggebeskrivelse E og E
Statens vegvesen Region Midt Elektrokontrakt Nordmøre og Romsdal Innhold Mappe I - Omfatter aktuelle drifts-/vedlikeholdsinstrukser og annen supplerende og utdypende grunnlagsinformasjon og/eller kravspesifikasjon
DetaljerGIMOTA AG. Assembly Instructions Dataconnectors DIN F. Datenstecker Katalog Gimota AG 04/14
GIMOTA AG Assembly Instructions Dataconnectors DIN F 2019 Datenstecker Katalog Gimota AG 04/14 3 1 Assembly Instructions TRAC DIN-F 1.1 Preparation Standard Part sets Parts sets are supplied corresponding
DetaljerElektronisk termostat med spareprogram. Lysende LCD display øverst på ovnen for enkel betjening.
Elektronisk termostat med spareprogram. Lysende LCD display øverst på ovnen for enkel betjening. 27.5 LCD Electronic thermostat with program setting. Bright LCD display placed at the top of the heater
DetaljerInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2760 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
DetaljerInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2766 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
DetaljerElektronisk innlevering/electronic solution for submission:
VIKINGTIDSMUSEET Plan- og designkonkurranse/design competition Elektronisk innlevering/electronic solution for submission: Det benyttes en egen elektronisk løsning for innlevering (Byggeweb Anbud). Dette
DetaljerPerpetuum (im)mobile
Perpetuum (im)mobile Sett hjulet i bevegelse og se hva som skjer! Hva tror du er hensikten med armene som slår ut når hjulet snurrer mot høyre? Hva tror du ordet Perpetuum mobile betyr? Modell 170, Rev.
DetaljerProduct Manual Produkthåndbok
BEAM Product Manual Produkthåndbok BEAM Technical Specifications Tekniske Spesifikasjoner Description Product number Mode Voltage Current Vehicle interface Cable length Encapsulation Operating temperature
DetaljerMounting the electrically elevating legrest
ASSEMBLY INSTRUCTION Mounting the electrically elevating legrest EN NO 9000A ..8 9000 Mounting the electrically elevating legrest Preparation Note! Switch off the wheelchair via remote control. Instructions
DetaljerSafeRing / SafePlus Retrofit of auxiliary switch S10 for position indication of earthing switch De module
SafeRing / SafePlus Retrofit of auxiliary switch S10 for position indication of earthing switch De module Installation instructions www.abb.com Document status Responsible RELEASED NODIS Location Date
DetaljerEMS 1. Music Streamer. Owner's Manual
EMS 1 Music Streamer Owner's Manual EN N 2 ENG About the EMS 1 Electrocompaniet Music Streamer This unit is designed to work with the Electrocompaniet PD 1 DAC only. A radio link is established between
DetaljerNorsk (English below): Guide til anbefalt måte å printe gjennom plotter (Akropolis)
Norsk (English below): Guide til anbefalt måte å printe gjennom plotter (Akropolis) 1. Gå til print i dokumentet deres (Det anbefales å bruke InDesign til forberedning for print) 2. Velg deretter print
DetaljerRotagrip Ltd Tel 0044 (0) Website FOR VPC-TYPE. Speed Max R.P.M. Speed Max R.P.M.
Light Duty Live Center Center is made of SCM420 alloy steel by heat treatment to provide higher rigidity wear-resistance. Center is constituted by ball bearings assembly. Applicable to middle-speed & high-speed
DetaljerMONTASJEANVISNING INSTRUCTIONS FOR ASSEMBLY AND USE
MONTASJEANVISNING INSTRUCTIONS FOR ASSEMBLY AND USE Småvarereol R 3000 Shelving unit R 3000 ZERTIFIZIER T 1. Gavl / Upright frame 2. Hylle / Dividing shelf 3. Krysstag / Back braces 4. Gitter bakvegg /
DetaljerOMT Technical Information. Versions OMT. Versions
Versions Versions Mounting flange Shaft Port size European version US version Drain connection Check valve Low pressure release High pressure release Main type designation Standard Wheel Brake-wheel G
DetaljerTRAPPETA RN MONTERINGSANVISNING
[Skriv inn tekst] TRAPPETA RN MONTERINGSANVISNING 3 x 1,6 m Trappetårn Monteringsveiledningen er laget for å gi en beskrivelse på monteringen av Delta TRAPPETÅRN. Delta TRAPPETÅRN er typegodkjent under
DetaljerFYSMEK1110 Eksamensverksted 23. Mai :15-18:00 Oppgave 1 (maks. 45 minutt)
FYSMEK1110 Eksamensverksted 23. Mai 2018 14:15-18:00 Oppgave 1 (maks. 45 minutt) Page 1 of 9 Svar, eksempler, diskusjon og gode råd fra studenter (30 min) Hva får dere poeng for? Gode råd fra forelesere
DetaljerSafeRing / SafePlus Retrofit of auxiliary switch S7 & S10 for position indication of load break switch and earthing switch C, F and SI modules
SafeRing / SafePlus Retrofit of auxiliary switch S7 & S10 for position indication of load break switch and earthing switch C, F and SI modules Installation instructions www.abb.com Document status Responsible
DetaljerEksamen KVT2002 Elenergi og automatiseringssystem/systemer. Programområde: Kulde- og varmepumpeteknikk. Nynorsk/Bokmål
Eksamen 01.06.2016 KVT2002 Elenergi og automatiseringssystem/systemer Programområde: Kulde- og varmepumpeteknikk Nynorsk/Bokmål Nynorsk Eksamensinformasjon Eksamenstid Hjelpemiddel Eksamen varer i 4 timar.
DetaljerAVS MAGMA SOLENOID VALVES
8 AVS Ing. J.C. Römer GmbH Reismühle 3 3D-98 Grafenau E-Mail: info@avs-roemer.com MAGMA the valve principle from AVS-Römer Medium separated MEDIUM SEPARATED Lever actuated seat valve with separating membrane
DetaljerDODGE. 12K Custom SuperRail Mounting Kit #3122. Gross Trailer Weight (Maximum)...12,000 lbs. Vertical Load Weight (Max. Pin Weight)...3,000 lbs.
DODGE 12K Custom SuperRail Mounting Kit #3122 Gross Trailer Weight (Maximum)...12,000 lbs. Vertical Load Weight (Max. Pin Weight)...3,000 lbs. Installation Instructions SPECIFICATIONS Fits 2009-2017 Dodge1500
DetaljerZB5AV04 ( ) Signallampe rød for BA9s
Produktdatablad Karakteristikk ZB5AV04 (43 039 21) Signallampe rød for BA9s Hovedkarakteristikk Produktspekter Produkt eller komponent type Produktkompatibilitet Kortnavn utstyr Innfatningsmateriale Montasjediameter
DetaljerInstallation Instructions
DODGE 16K Industry Standard Rail Custom Mounting Kit #2764 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
DetaljerEndelig ikke-røyker for Kvinner! (Norwegian Edition)
Endelig ikke-røyker for Kvinner! (Norwegian Edition) Allen Carr Click here if your download doesn"t start automatically Endelig ikke-røyker for Kvinner! (Norwegian Edition) Allen Carr Endelig ikke-røyker
DetaljerBruk av Aluminium Offshore & i Industrien
& i Industrien Slide 1 Aluminium Historie Oldtidens grekere og romere kjente til aluminiumsalter, men først i 1808 ble metallet aluminium identifisert Først isolert i ren form i 1827 Før dagens fremstillingsprosess
DetaljerMCP-16RC, luftrenertårn
Kompakt filterkassett med pulsrengjøring MCP-16RC luftrensertårn er en kompakt filterkassett for desentralisert inneluftrengjøring der luftgjenoppretting er mulig. Den kompakte filterenheten leveres med
DetaljerBytte til split Collin Lanyard RSL. Obligatorisk - alle rigger skal ha dette montert ved hopping etter 01.01.2015.
S e r v i c e o r d r e M a t e r i e l l Materiellsjef F/NLF kommuniserer pålegg omkring forhold som ansees som vesentlige for å oppnå de målsettinger som er satt for materiellarbeidet via denne Service
DetaljerSTILLAS - STANDARD FORSLAG FRA SEF TIL NY STILLAS - STANDARD
FORSLAG FRA SEF TIL NY STILLAS - STANDARD 1 Bakgrunnen for dette initiativet fra SEF, er ønsket om å gjøre arbeid i høyden tryggere / sikrere. Både for stillasmontører og brukere av stillaser. 2 Reviderte
DetaljerFrode Endresen. Installasjonskrav ved fiskal gassmåling Hvorfor anbefales stadig de mest konservative løsningene?
Frode Endresen Installasjonskrav ved fiskal gassmåling Hvorfor anbefales stadig de mest konservative løsningene? Ultralyd gassmåler Vært på markedet siden siste del av nittitallet Befestet sin posisjon
Detaljer