KAMPANJE AKK : Skifte setetrekk forseter

Størrelse: px

Begynne med side:

Download "KAMPANJE AKK : Skifte setetrekk forseter"

Sidsel Knudsen
6 år siden
Visninger:

1 KAMPANJE AKK : Skifte setetrekk forseter Berørte modeller: SX4 S-Cross AKK416 / AKK416D, totalt 220 biler. Liste med chassisnummer legges ikke ved, bruk Forhandlerweb til å sjekke om bilen er omfattet av kampanjen! Kunder tilskrives. Kampanjebrev mottatt av kunde inneholder kampanjekode. Kontroller kundebrev for riktig kampanjekode, om bilen skal ha AKK-5 eller AKK-6. Om kunden ikke har med brev, bruk Forhandlerweb! Noen av bilene kan også allerede ha fått utført kampanjen før levering. Kampanjen er i praksis identisk med AKK-6, men med forskjellig delenummer og defektkode. Det er viktig å legge inn rett kode for rett bil. Problem/symptomer: Mulig feil på sting i seterygg som kan påvirke sideairbag. Tiltak: Skifte setetrekk på forseter, kun rygg (ikke setepute). Delebehov: 1 stk R30-AN7 NB! Inneholder trekk for seterygg begge sider. Delenummeret er et annet enn AKK-6! Deler til denne kampanjen blir ikke belastet dere, og skal således heller ikke påføres reklamasjonen. Tilleggsinformasjon: Kampanjen er opprettet på Forhandlerweb. Velg "Kampanjesøk" på "Dashbord" (siden du kommer til ved innlogging) og legg inn VIN. Om bilen er omfattet av kampanjen vises dette på skjermen. Kampanjen heter AKK-5. Utfør også eventuelle andre åpne kampanjer. Det dekkes 1,5 timer for skifte av trekk på begge sider. Ved reklamasjon: Legg inn chassisnummer/registreringsnummer under "Teknisk" / "Opprett Reklamasjon" på Forhandlerweb og trykk på "Søk". Trykk på "Velg" når bil kommer opp under "Søkeresultat" Du får nå valget mellom å opprette en blank reklamasjon eller en forhåndssøknad eller en kampanje. Merk av for kampanje AKK-5 "Skifte setetrekk", fyll ut datoer, arbeidsordrenummer og kilometerstand og lagre. Ved siden av kampanjekode "AKK-5" velges «Skifte setetrekk». Rapporten fylles automatisk ut med arbeid. Deler sendes vederlagsfritt og krediteres ikke. Trykk så på "Send reklamasjon" nederst på siden. Rapport ferdig. Se også eget skriv angående kampanjesøk og innlegging av kampanjer som finnes på samme sted som dette skriv på RSA Ekstranett. Kampanje AKK Dato: Revisjon C

2 ANNEX1 SX-4 S-Cross Fr seat: seat back trim Repair instruction

3 1. Vehicle Identification VIN Confirm VIN with the Embossing on cowl top panel in Engine compartment and/or ID plate which put on the side sill panel bottom of B pillar. VIN ID plate 1

2. Replacement work procedure of seat back trim Set Part Number List for Countermeasure on each type vehicle Steering Trim specification Remark Part No.

Pass seat 85380-64R30-AN7 5 Fabric:Single stitch Without pocket 85380-64R00-AN2 6 With pocket on Pass seat 85380-64R20-AN2 7 RHD Fabric:Double stitch With pocket on Pass seat 85380-64R20-AN1 8

4 2. Replacement work procedure of seat back trim Set Part Number List for Countermeasure on each type vehicle Steering Trim specification Remark Part No. with C/M 1 Without pocket R00-AN2 Fabric:Single stitch 2 With pocket on Pass seat R10-AN2 LHD 3 Fabric:Double stitch With pocket on Pass seat R10-AN1 4 Leather With pocket on Pass seat R30-AN7 5 Fabric:Single stitch Without pocket R00-AN2 6 With pocket on Pass seat R20-AN2 7 RHD Fabric:Double stitch With pocket on Pass seat R20-AN1 8 Leather With pocket on Pass seat R40-AN7 Each of above set part number include the All C/M (countermeasure) Parts mentioned below, to replace the left and right seat back trim of one vehicle. Trim comp for LH and RH C-ring (to fasten the trim to pad): 16 Fastener (to fasten the cut area of trim): 2 (Fasteners are basically supplied with sewn on the trims. Separated supply is done only at the beginning. Please confirm whether they are contained regardless of supplied condition.) Double stitch is shown by white color stitches in the photo. (In case of single stitch, the above white stitch does not exist as shown in the right photo.) 2

5 Fixing point of the seat back trim (Rh Seat Back shown in the pictures. In case of Lh Seat Back, fixing point can be identified in symmetrical position.) Fixed (Fastened) by C-ring: 6 places [Front side of seatback] Fixed by headrest guides: 2 places Fixed by C-ring: 2 places [Tail side of seatback] 3

6 Fixed by resin bracket: 2 places Fixed by resin bracket: 2 places Fixed by nut: 1 place Fixed by resin bracket: 2 places Tightening Torque M6 Nut: 5.5±1.5 Nm 4

3) Cut the trim to the slit of which side airbag harness (together with seat heater harness for seat heater specification model) passed like the photo with scissors.

7 3. Removal (Rh Seat shown in the pictures) 1) Move the seat to the front end by shift slide lever, then get down the seat back to front by reclining lever. 2) Remove the matching part at tail side and bottom of seat back. 3) Cut the trim to the slit of which side airbag harness (together with seat heater harness for seat heater specification model) passed like the photo with scissors. Caution: Do not damage the harness when cut the trim. Cut the trim like the above photo 4) Roll up the seat back trim, and remove the first resin bracket which secured the trim on frame Reverse side of trim shown in the photo, after the trim removed from frame, for your better understanding Resin Bracket 5

8 5) Roll up the trim again and remove the securing nut located at the outside of seat, then take off the metal bracket from the stud bolt. Nut Metal Bracket Metal Bracket 6) Roll up the trim again, and remove the second resin bracket (which secured trim on frame) from the frame. Resin Bracket 6

9 7) After change the location of worker to be front side of seat back and pull up the seat back, remove the two C-rings shown in the photo. Caution: Never use the removed C-rings, and new C-rings must be used. As C-ring was not originally located on the center, it was/is not abnormal but OK. 8) After change the location of worker to be tail side of seat back, roll up the trim again, and remove the third resin bracket (which secured trim on frame) from the frame. Resin Bracket 9) Take off the two C-rings shown in the photo. Caution: Never use the removed C-rings, and new C-rings must be used. 7

10 10) After change the location of worker to be front side of seat back, remove the C-rings located on the 4 address shown in the photo. Caution: Never use the removed C-rings, and new C-rings must be used. 11) Remove the headrest and take off the trim comp from the seat. 8

4. Installation Paying attention to the point mentioned below, install the parts by just the reverse steps of disassembling procedure.

Caution: If the C-ring not installed correctly, C-ring may be come off or trim being be damaged by the end of C-ring to cause the visual problem of seat, or human being may be injured by the end

Caution: If the cloth installed under kinked condition, side airbag may not be deployed correctly. So, the metal bracket must be installed correctly with cloth not to be kinked.

11 4. Installation Paying attention to the point mentioned below, install the parts by just the reverse steps of disassembling procedure. C-ring must be installed correctly pinching it until the end come to the correct position as shown in the middle photo below and getting the end to face in urethane form side. Caution: If the C-ring not installed correctly, C-ring may be come off or trim being be damaged by the end of C-ring to cause the visual problem of seat, or human being may be injured by the end of C-ring. Not enough Correct Too much When reinstall the metal bracket with cloth on the frame which removed at item 5), pay attention to the cloth not to be kinked. Caution: If the cloth installed under kinked condition, side airbag may not be deployed correctly. So, the metal bracket must be installed correctly with cloth not to be kinked. Cloth not to be kinked, when installing Bracket When reinstall the metal bracket on the frame which removed at item 5), follow the below turns. Caution: If the metal bracket installed by wrong turns, side airbag may not be deployed correctly. So, the metal bracket must be installed by turns mentioned below. 1st 2nd 9

Secure the nut which removed at item 5), by the correct tightening torque. Caution: If the nut tightened by wrong torque, side air bag may not be deployed correctly.

5 Nm Cut part at item3) must be secured by fastener referring to the below photos, as the final countermeasure part will also be cut as same shape.

12 Secure the nut which removed at item 5), by the correct tightening torque. Caution: If the nut tightened by wrong torque, side air bag may not be deployed correctly. So, the nut must be installed by correct torque mentioned below. Tightening Torque M6 Nut: 5.5±1.5 Nm Cut part at item3) must be secured by fastener referring to the below photos, as the final countermeasure part will also be cut as same shape. Set the side airbag harness (only or with seat heater harness), referring to the above photo. Secure by fastener. When secure the resin bracket which removed at item2), make sure not to be NG but to be OK condition shown below. OK: Pad was partially coming out from the frame. NG: Pad was located all in the frame. 10

Like dokumenter

KAMPANJE APK : APK-8: Bytte bakaksel bolter

KAMPANJE APK : APK-8: Bytte bakaksel bolter KAMPANJE APK-8 20160222: APK-8: Bytte bakaksel bolter Berørte modeller for APK-8: Vitara APK, S-cross AKK, og Swift AZG. Totalt 454 biler på det norske markedet. Liste med chassisnummer legges ikke ved,