KABELSTIGER OG TILBEHØR FOR SKIP CABLE LADDERS AND ACCESSORIES FOR SHIPS Being first is good, being smart is better, being both is Simply the Best!
Firmapresentasjon Company presentation PRODUKT- INFORMASJON Øglænd System tilbyr opphengssystemer tilpasset alle faggrupper, kabelstiger, kabelbaner, koblingsboksstativ, rørklammer, kabelklammer (trefoil cleats), varmekabler, styringssystemer m.m. Har du spørsmål? Vennligst ta kontakt. Last ned siste versjon av våre produktkataloger fra: Download our latest version of product catalogues from: www.oglaend-system.com PRODUCT INFORMATION Oglaend System offer a broad range of cable support systems for all applications, e.g. cabie Iadders, cable trays, junction box racks, tubing clamps, cable cleats, heating cables, control systems etc. If you need further information, please do not hesitate to contact us! 2
www.oglaend-system.com Front page: Photo courtesy of Akershus University Hospital MATERIAL NAVN / MATERIAL TYPES: PG = Pregalvanisert stål Pre galvanized steel 20 my zink HDG = Varmgalvanisert Hot Dip Galvanized NS/ISO 46* SS = Rustfritt stål Stainless Steel AISI 36L** AL = Aluminium Aluminium 52 H22/H32 CS = Ubehandlet stål Carbon steel (Black steel) EN 00-S355J2 *) Steel quality for HDG: Steel grade EN 0 Grade DC0 **) Steel quality for SS: EN.4404 Andre kvaliteter på forespørsel / Other material qualities on request. SYMBOLER FOR SKRUER / SYMBOLS FOR SCREWS: Symbolet viser skruetype, minimum antall og typebenevnelse. Bestillingsnummer er på s.. SYMBOLEKSEMPLER: Ekspansjonsbolter Behov: 2 stk. Type M0x55 Låseskrue m. linsehode Behov: stk. Type M0x20. Sekskantskrue Behov: Min. 2 stk. (4) Kan brukes*. Type M6x2. Selvborende skrue Behov: 6 stk. Type 4x32. Standard: Skruer er inkludert! Oppgitt skrueantall før parentesen leveres standard med delene. (4) Skruer i parentes er IKKE inkludert! Ved spesielle forhold sikres montasjen med antall oppgitt i parantes. Disse ekstra skruene bestilles separat. Skruer IKKE inkludert! En skruetypeguide, men ikke inkludert. 2(4) M0x 2 M0x55 M0x20 2(4) M6x2 6 4x32 Standard: Screws are included! Listed number screws before brackets are supplied standard with the parts. (4) Screws in brackets are NOT included! The listed number put in brackets is to secure the set up in special conditions. These additionals need separate order. Screws NOT Included! A type guide but not included. SNI This symbol shows type of screw, the number needed and name. For order no. see page. SYMBOL EXAMPLES: Expansion bolts 2 pcs. needed. Type M0x55. Locking screws pcs. needed. Type M0x20. Hexagonal screws Minimum 2 pcs. needed. (4) May be used*. Type M6x2. Self tapping screw 6 pcs. needed. Type 4x32. Innhold: Contents: Rett til mindre forandringer forbeholdes. Subject to minor changes without notice. Symbolforklaring Explanation of symbols 3 Stigeprogram: RZE-R, PZE-P, RHF Range of Cable Ladders: RZE-R, PZE-P, RHF 4 Belastningstabell Safe working loads 5 Bend og vertikalbend Bends and Risers 5-7 RZE-R tilbehør / Accessories 5 RZE-P tilbehør / Accessories 6 RHF tilbehør / Accessories 7 Allsidig tilbehør Versatile Accessories 7-0 Boltsveiseoppheng Stud welding support RZE-R brukertips RZE-R best practice 2 MultiGrid Standard + Forenklet oppheng for skip Standard + Simplified support for ships 3 Alternative oppheng alle faggrupper Alternative multi-discipline support systems 4 Mekano Opphengskinner og sveisebraketter Support channels and welding brackets 5 SPB kabelbaner for alle formål cable trays for all purposes 6 ETIN instrumentrørklammer tube clamp 6 Perforerte profiler Perforated Profiles 7 Bolter og festemateriell Bolts and fixing items 8 Salgskontorer Locations 9 DNV Type Approval Certificate Oglaend System s ladder type RZE-R, RZE-P and RHF are certified by DNV, certificate no. E-83. The product range is tested according to IEC 6537. Quality control Oglaend System is certified by D.N.V. to conform to the Quality System Standard NS-EN ISO 900, which is the strictest quality code for contractors developing, designing and manufacturing their own equipment. Patenter og mønsterbeskyttelser Mange av Øglænd Systems produkter er patentert eller mønsterbeskyttet. En komplett liste er tilgjengelig ved henvendelse. Patents and design applications Many of Oglaend System s products are patented or protected by design applications.a complete list is available on request. 3
Kabelstigeprogram / Range of Cable Ladders RZE-R: The flexible and cost efficient ladder RZE-R stigen med «Z» trinn og spesialdesignet riservange, se side 2. RZE-R ladder with «Z» rungs and specially designed «riser slots», study page 2. 40 Standard lengde: 3m. Standard length: 3m. 8,5 B 23 8,5 4mm Position of the Z-Rung 20 x 7 2,5 39,8 23 8,5 8,5 RZE-R stiger / Ladders Type angir bredde B./ Type states width B. RP HDG Weight Type Art. no. Art. no. (kg/m) RZE-R-00 3720 85923 2,5 RZE-R- 372 85924 2,7 RZE-R-200 3722 859 2,9 RZE-R-0 3723 85926 3,2 RZE-R-3 3724 3,4 RZE-R-400 3725 85927 3,5 RZE-R-4 3726 85928 3,7 RZE-R-0 3727 85929 3,9 RZE-R-600 3728 859 4,2 0 26,3 RZE-P: The ladder for heavy loads 00 0 RZE-P med perforerte vanger RZE-P with slotted side-pieces Type angir bredde B./ Type states width B. 37 3 B 5 40 0 Position of the Z-Rung 75 35 20 x 7 2,5 35 x 28,4 37 3 RP HDG SS Weight Type Art. no. Art. no. Art. no. (kg/m) RZE-P-00 86793 86780 8689 3,0 RZE-P- 86794 8678 86820 3,2 RZE-P-200 86795 86782 8682 3,4 RZE-P-0 86796 86783 86822 3,6 RZE-P-0 86797 86784 86823 3,8 RZE-P-3 86798 86785 86824 4,0 RZE-P-400 86799 86786 868 4,2 RZE-P-4 86800 86787 86826 4,4 RZE-P-0 8680 86788 86827 4,6 RZE-P-600 86802 86789 86828 5,0 RZE-P-6 86803 86790 86829 5,3 RZE-P-7 86804 8679 868 5,7 RZE-P-900* 86805 86792 8683 6,3 *) 2 x 4 are recommended for 900 mm widths. Sidepieces in HDG have endslots x mm B 6 4 0 5 00 0 0 Flat Rung Position side piece Flat iron Rung x3 mm with holes 20x7 mm for widths 75-200mm. For widths 0-600mm flat iron Rung x4 mm RHF stiger / Ladders Type angir bredde B./ Type states width B. RP HDG SS Weight Type Art. no. Art. no. Art. no. (kg/m) RHF-00 78802 7880 865 2,9 RHF- 78803 788 8224 3,0 RHF-200 78804 7882 82074 3,2 RHF-0 78843 78846 3,5 RHF-0 78805 7883 8790 3,7 RHF-3 78844 78847 3,9 RHF-400 78806 7884 8232 4, RHF-4 78845 78848 4,3 RHF-0 78807 7885 82397 4,4 RHF-600 78808 7886 8365 4,9 4
Lasteevne pr. m: Tabellen viser maks. tillatt last ved sikkerhetsfaktor,7. Testprosedyren betinger at lengden på endespennet reduseres til 3/4 av supportavstanden. BELASTNINGSTABELL / SAFE WORKING LOAD Stigebr. Spenn Last (kg/m) Load (kg/m) according to IEC 6537 Ladder Support RZE-R RZE-P RHF width spacing HDG HDG RP 00-900,5 m 84 260 99 2,0 m 02 34 52 2,5 m 56 75 27 Capacity per m: The table indicates the maximum allowed uniformly distributed load. A safety factor of,7 is included. According to the test procedure the length of the end span must be reduced to 3/4 of the support spacing. Alle tester er utført i henhold til IEC 6537 / All tests are according to IEC 6537. RZE-R tilbehør / Accessories: Sidepieces in HDG have slots in the ends x mm B B + 0 B + R + 0 R 200 H sidevange / H side piece = 40 RZE-R bend 90 / Flat Elbow Type angir bredde B./ Type state width B. RP HDG Vekt (kg) Type Art. no. Art. no. Weight RZE-R FE- 85222 372068 2,9 RZE-R FE-200 84845 372069 3,2 RZE-R FE-0 84833 372070 4, RZE-R FE-400 84834 37207 4,8 RZE-R FE-4 84835 372072 5, RZE-R FE-0 84836 372073 5,5 RZE-R FE-600 84837 372074 6,2 RZE-R FE-7 85358 372075 7,9 RZE-R FE-900 84838 372076 9,0 8 M0x T-avgreiningsbrakett og kryss Tee- and Cross-Piece Bracket HDG SS Vekt (kg) Type Art. no. Art. no. Weight RZE-P TE-PA 87972 87973 0,8 Leveres som to braketter med 8 stk. M0x SS. Supplied as 2 brackets with 8 screw M0x SS. Andre løsninger for T-AVGREINING på forespørsel. Other T-PIECE solutions on request. 2 M0x Splice connector for perforated side pieces 4 3 60 Skjøtelask for RZE complete with 2 x M0. Splice Connector for RZE complete with 2 x M0 screws. HDG SS Vekt (kg) Type Art. no. Art. no. Weight RZE SC-40-P 8556 82873 0,2 20 00 T= 2,5 Side 2 / Page 2 Riser-løsninger se s. 2 Riser solutions see p. 2 5
RZE-P tilbehør / accessories: RZE-P bend 90 / Flat Elbow 90 Type angir bredde B./ Type state width B. B B + 0 B + R + 0 R 200 H sidevange / H side piece = 40 RP HDG SS Vekt (kg) Type Art. no. Art. no. Art. no. Weight RZE-P 90-00 87678 87652 87665 2,5 RZE-P 90-87679 87653 87666 2,9 RZE-P 90-200 87680 87654 87667 3,2 RZE-P 90-0 8768 87655 87668 3,5 RZE-P 90-0 87682 87656 87669 3,8 RZE-P 90-3 87683 87657 87670 4, RZE-P 90-400 87684 87658 8767 4,4 RZE-P 90-4 87685 87659 87672 5,3 RZE-P 90-0 87686 87660 87673 5,6 RZE-P 90-600 87687 8766 87674 6,4 RZE-P 90-6 87688 87662 87675 6,7 RZE-P 90-7 87689 87663 87676 8,4 RZE-P 90-900 87690 87664 87677 9,7 8 M0x T-avgreiningsbrakett og kryss Tee- and Cross-Piece Bracket HDG SS Vekt (kg) Type Art. no. Art. no. Weight RZE-P TE-PA 87972 87973 0,8 Leveres som to braketter med 8 sett M0x HDG / M0x20 SS. Supplied as 2 brackets with 8 sets M0x HDG / M0x20 SS. Andre løsninger for T-avgreininger på forespørsel. Other Tee-Piece solutions on request. 2 M0x Splice connector for perforated side pieces 4 3 60 Skjøtelask for RZE komplett med 2 x M0 skruer. Splice Connector for RZE complete with 2 x M0 screws. HDG SS Vekt (kg) Type Art. no. Art. no. Weight RZE SC-40-P 8556 82873 0,2 20 00 T= 2,5 8 M0x RZE-P Riser Bracket 45 PG Vekt (kg) RZE-P RB-45 8769 0,2 Leveres i par med 8 sett M0x HDG. Supplied in pairs with 8 sets M0x HDG. 6
RZE-P tilbehør / Accessories: Rung profile RHF bend 90 / Flat Elbow 90 Type angir bredde / Type state width Sidepieces in HDG have slots in the ends x mm r = 00 mm for widths 75-0 r = 200 mm for widths 3-600 RP HDG SS Vekt(kg) Type Radius Art. no. Art. no. Art. no. Weight RHF-B-00 R=00 8807 888 8829,5 RHF-B- R=00 8808 889 88,7 RHF-B-200 R=00 8809 8820 883 2,0 RHF-B-0 R=00 880 882 8832 2,5 RHF-B-0 R=00 88 8822 8833 2,8 RHF-B-3 R=200 882 8823 8834 4,0 RHF-B-400 R=200 883 8824 8835 4,4 RHF-B-4 R=200 884 88 8836 4,7 RHF-B-0 R=200 885 8826 8837 5, RHF-B-600 R=200 886 8827 8838 5,9 M6x T-stykke brakett Tee-Piece Part HDG Vekt (kg) RHF TE-PA 824 4 x 0, Leveres som 4 braketter og 2 stk. M6xSS. Supplied as 4 brackets with 2 M6xSS. Rung profile Sidepieces in HDG have slots in the ends x mm r = mm RHF Riser 90 Type angir bredde B./ Type state width B. RP HDG SS Vekt (kg) Type Art. no. Art. no. Art. no. Weight RHF RI-00 78954 78966 8264 2,0 RHF RI- 78955 78967 82244 2,2 RHF RI-200 78956 78968 82076 2,5 RHF RI-0 78957 78969 2,8 RHF RI-0 78958 78970 82245 3,0 RHF RI-3 78959 7897 3,2 RHF RI-400 78960 78972 8434 3,5 RHF RI-4 7896 78973 3,8 RHF RI-0 78962 78974 82403 4,0 RHF RI-600 78963 78975 8367 4,4 M0x Skjøtelask for RHF komplett med x M0 skrue og pressplate. Splice Connector for RHF complete with x M0 screw and pressplate. 5 3 Splice connector for unperforated side pieces HDG Vekt (kg) RHF SC--U 85472 0,2 Annet tilbehør / Other accessories: 2 M0x The verical hinge can be adjusted in 4 steps 40 mm mm RZE HV RHF HV Leddbeslag for RZE og RHF Hinge Vertical for RZE og RHF HDG SS Vekt Type Art. no. Art. no. Weight RZE HV 8575 0,9 kg RHF HV 8785 8378 0,3 kg 7
M0x CC= 44 mm + width B x20 mm 40 Stigefeste Fixing Clamps For fixing ladders to brackets and support. HDG SS Vekt (kg) Type Art. no. Art. no. Weight RZE FC-40 372099 86876 0,05 RHF FC- 78904 86875 0,05 40 2 mm M0x Opphengsbeslag For oppheng av stiger med feste på begge stigevanger. Fixing Clamp to channel For ladder support with fasteners on both side pieces. 40 mm HDG Vekt (kg) RZE FC-CH-/40 372098 0,5 RZ pendelkonsoll for skinne RZ Central Support for channel HDG Vekt (kg) RZE CS- 82820 0,8 RZE CS-200 8282 0,9 RZE CS-0 82822,5 RZE CS-400 82823,35 RZE CS-4 82824,45 RZE CS-0 828,55 RZE CS-600 82826,8 RZE CS-7 82827 2,35 RZE CS-900 82828 2,5 Ingen byggehøyde under konsollen. Pendelopphenget gjør installasjonen og kabeltrekkingen enklere. Installation space is saved because nothing is projecting below the bottom run of ladder. The single central support facilitates easier cable pulling. Se opphengsvarianter s. 2-3 og opphengskinner s. 4. Study support solutions p. 2-3 and support channels p. 4. Material thickness: 4 mm x mm x35 40x4 Vinkelstål flattstål med sveisestykker Angle iron Flat Bars with Welding Strips Available in lengths of 3 m. RP HDG SS Vekt (kg/m) Type Art. no. Art. no. Art. no. Weight FI WS-HO 78832 78897, AI WS-VE 7883 78896, 294 AI WS-VE kan bøyes vertikalt / for vertical bending. FI WS-HO kan bøyes horisontalt / for horizontal bending. 8
85 9x2080 43 Sveisebrakett for armatur og 00mm kabelbane Welding Bracket for light fitting and 00mm cable tray RP Vekt (kg) S-RZE LB-WB 8595 0,5 85 Material thickness: 2 mm Utstyrsbrakett Socket Plate as welding bracket PG Vekt (kg) A-RZE SO-WB SP370* 0,3 *) Klar for kundetilpasset hullmønster *) Pre-slotted for client design Welding angle 45 M6x2 M8x20 Armaturfeste Light fitting fixing Bracket SS Vekt (kg) A-RZE LB-Ceag 83599 0,08 A-RZE/RHF LB-Glamox* 8568 0,08 *) For armatur med 2 festehull CC 60 mm. *) For light fitting with 2 fixing holes CC 60 mm. 3 M6x20 CC 60mm 00 2 M0x 85 45 Stikkontaktfeste Socket Plate for RZE-R and -P PG Vekt (kg) A-RZE SO-40 8594 0,4 9
Avgangsbrakett med klipsfeste Exit Plate for ladder snap on SS Vekt (kg) A-RZE/RHF EX 83598 0,07-2,5 mm Kantbeskyttelse Volvolist Edge Protector Type Art. no. spool (m) A-SPB EP 265 A-SPB EP-SS* 264 00 A-RZE EP 84636 *) SS-reinforced for use on SS-tray 3-5 mm Kabelholder for vertikalt trinn Cantilever Arm for temporary use PG Vekt (kg) A-RZE CA 85437 0,3 Rig n Roll Push to open Press to close «Rig n roll» Kabeltrekkerrulle Cable pulling Tool Type Art. No. Rig n Roll size. Up to 60mm cables 84629 Rig n Roll size 2. Up to 20mm cables 84628 Use Rig n Roll to facilitate fast speed in fast cable pulling: Two sizes fitting up to 60 mm and 20mm cables. Easy to fix to any of our cable ladders no tools needed. Easy to open and lock no tools needed. Easy to handle due to its small size and low weigth (400g). No loose parts or screws. In use on OE ladder 0
Boltsveiseoppheng Stiger og baner Stud welding support Ladders and trays Threaded inserts for stud welding to wall. Skruebolter / Threaded Inserts SS Type Bolt Art. no. Studw-07 M0 x 372896 Studw-08 M0 x 372897 Studw- M2 x 372898 Skruebolter "skytes" fast for festing av veggkonsoll. Threaded inserts are stud welded to fix wall brackets. Ved behov kan teflonisolasjon mot korrosjon leveres. Teflon isolation to protect against corrosion is supplied on request. 00 7 x x 20 65 Festebrakett for Hilti skuddboltsystem Bracket for Hilti powder actuated tool system HDG SS Type Art. no. Art. no. S-SPB SB-PO 372902 834 Stud welding M6x2 Free 360 rotation Ø 7mm Festebrakett for ETIN* Support Bracket for ETIN* SS Weight Type Art. no. SS (kg) A-UNO D-02-B 294 0,2 *) Les om ETIN på s. 6, eller be om ETIN-brosjyre. *) Study ETIN on page 6, or ask for ETIN brochure.
RZE-R stigen i bruk: Bare kutt og bøy! RZE-R ladder best practice: Simply cut and bend! RZE-R stigen er designet spesielt for å kunne monteres forbi hindringer. The RZE-R ladder is specially designed to avoid obstacles. Riserjustering: Åpne triangelhullet og bøy til 45 eller form ønsket vinkel. Lås med sveisenest. Riser adjustments: Open the triangle slot and bend to 45 or form the angle you need. Fix by welding. Hold Press Justering sideveis: Bruk eksempelvis en pall og plasser vangens bøyehull på kanten. Hold stigen fast mot flaten og den «løse» enden presses enkelt ned til ønsket vinkel. Sideways adjustments: Use e.g. a pallet and place the vertical slot on the corner edge. Then bend the sidepieces simply by pressing the straight ladder firm to the wall and push the «loose» end to form the angle. Forenklet T-avgreining er en smart løsning! Se side 5+6. Simplified T-piece bracket is a smart solution! See page 5+6. I utsatte områder kan kablene beskyttes med kantbeskytter. Se side 0. 2 In exposed areas protect the cables with Edge protector. See page 0.
MultiGrid for ships 2 Standard oppheng: Standard opphengsplan for MultiGrid til skip. : Monteres av skrogbygger: Kun sveiseskinnene skal monteres av skrogbygger. Skinnene som leveres i utførelse svart stål (CS), monteres over utstyrstrasé og blir malt sammen med resten av skroget. Sveiseskinner i lengder på,5m monteres parallelt med stringerne med avstand på ca. 2m. 0,6m lengder monteres mellom og inntil stringerne, se illustrasjon. Disse bidrar også til å stive opp stringerne. NB! Ingen kabelstiger monteres hos skrogbygger da forandringer mht. utrustning vil forekomme. Sveiseskinne (CS Ubehandlet stål): S-M WCH-00L = 0,6m Art. nr. 87999 S-M WCH-00L =,5m Art. nr. 8567 2: Monteres av skrogutruster: Varmgalvaniserte kabelstiger monteres til skinnene med skruebraketter. Skinnene gir festepunkt i hele traseen. Ingen etterbehandling er påkrevd og kabelinstallasjon kan starte umiddelbart. Enkle rør og annet utstyr kan monteres i samme trasé. Den store fleksibiliteten i forhold til å kunne gjøre endringer gir en svært kostnadseffektiv installasjon. Standard support: Standard support plan for MultiGrid on ships. : Fixed by fabricator: Only the welding profiles are fixed in the construction yard. Welding profiles are supplied in carbon steel (CS) to be painted together with the hull. The channels are welded to the ceiling above the equipment route. The profiles are installed in lengths of.5m in parallel with the stringers with 2 m distance between them. Profiles of 0.6m lengths are installed between the stringers. See illustration. These will also function as stiffeners for the stringers. Please note: No cable ladders are installed at the construction site because of the high risk of equipment changes. Welding channels (CS Black steel): S-M WCH-00L = 0,6m Art. nr. 87999 S-M WCH-00L =,5m Art. nr. 8567 2: Fixed by the installation contractor: Hot dip galvanised cable ladders are fixed to the channels with bolts and brackets. The channels provide fixing points throughout the equipment route. There is no need for repainting, and the installation of cables can start immediately. Small pipes and other equipment can be installed using the same fixing points. The flexibility makes it easy to reroute equipment, making this a very cost efficient solution. VIKTIG! Bare festepunkt monteres hos skrogbygger. Da kan skrogutruster skruemontere utstyr uten behov for ekstra maling. Komplett Complete IMPORTANT! Only fixing points are installed by the fabricator. Then the installation contractor can fit the equipment needed without need of repainting. 2 2 m Stigebredde Ladder width Forenklet oppheng: Simplified support: Forenklet opphengsplan for MultiGrid til skip. : Monteres av skrogbygger: Kun festebrakettene monteres av skrogbygger. Festebrakettene som leveres i utførelse svart stål (CS), monteres over utstyrstrasé og blir malt sammen med resten av skroget. Innbyrdes avstand mellom festepunktene skal være tilpasset planlagt kabelstigebredde og ca. 2m i lengderetning. NB! Ingen kabelstiger monteres hos skrogbygger da forandringer mht. utrustning vil forekomme. Festebrakett: Rødprimet S-M WB-200-UNO-3 = Art. nr. 87998 2: Monteres av skrogutruster Varmgalvaniserte kabelstiger monteres til brakettene med skruer. Ingen etterbehandling er påkrevd og kabelinstallasjon kan starte umiddelbart. I samme trase kan enkle rør og annet utstyr monteres. Festebrakettene kan forlenges med 0mm skinner eller perforerte UNO-skinner. Brakettene i kombinasjon med skinner gir festepunkt gjennom hele traseen. 0mm skjøteskinne = Art. nr. 87997 3m UNO-4-3P = Art. nr. 83970 For mer kompliserte installasjoner anbefales standard opphengsplan med sveiseskinne (se over). Simplified support plan for MultiGrid on ships. : Fixed by fabricator: Only welding brackets are installed in the construction yard. The brackets are supplied in carbon steel (CS) to be painted together with the hull. The brackets are welded to the ceiling above the equipment route. The placing of the brackets is depending on the width of the planned cable ladder. The distance between the brackets along the length of the cable ladder should be roughly 2m. Please note: No cable ladders are installed at the construction site because of the high risk of equipment changes. Welding bracket: Red oxide painted S-M WB-200-UNO-3 = Art. nr. 87998 2: Fixed by installation contractor: Hot dip galvanised cable ladders are fixed to the brackets with bolts. There is no need for repainting, and the installation of cables can start immediately. Small pipes and other equipment can be installed using the same fixing points. The brackets can be extended by 0mm splice channels or perforated UNO channels. The brackets combined with channels give fixing points throughout the equipment route. 0mm splice channel = Art. no. 87997 3m UNO-4-3P = Art. no. 83970 For more complicated systems the standard support plan using welding channels are recommended (see above). 3
Alternative opphengløsninger: Eksempelvis til offshoreinstallasjoner Alternative support solutions: E.g. for offshore installations Felles oppheng for alle faggrupper Multidiscipline support ØS Pipe clamps Sveiseskinne L-profil med sveisetapper. Materialtykkelse: 4mm Art. no.: CS 8567 SS 8568 Ladder RZE-P Vinkelskinne S-M CH-2 eller perforerte vinkeljern S-M CH- Welding channel L-profile with welding taps. Material thickness: 4mm Art. no.: CS 8567 SS 8568 Angle channel S-M CH-2 or preslotted angle iron 0 RZE CS Ladder RZE-P RZE FC-CH-40 Ladder RZE-R Skrues fast direkte eller med braketter. Fasten directly or by using brackets. For sveisebraketter og opphengskinner, vennligst se neste side, eller spør etter vår MultiGrid katalog for opphengsystemer. For welding brackets and support channels please study the next page or ask for our MultiGrid support system catalogue. Eksempler på smarte løsninger: Våre kataloger er fulle av gode eksempler på hvordan våre produkter kan anvendes. Her finner du smarte kostnadsbesparende løsninger sammenlignet med tradisjonelle installasjoner. Les mer i hovedkatalogene som er vist på side 2, eller besøk www.oglaend-system.com Best practice Our catalogues contain many good examples on how to use our products. Learn about smart cost effective solutions compared with traditional installations. Read more in the main catalogues listed in page 2 or visit www.oglaend-system.com 4
Alternative opphengløsninger: Alternative support solutions: Opphengskinner: Support channels: Materialtykkelser: HDG = 2mm. SS =,5mm. Material thickness: HDG = 2mm. SS =,5mm. 7 7 39 22 22 00 22 7 60 S-M CH- S-M CH-2 S-M CH00- S-M CH60-2 60 9 62 39 00 39 S-M CH00-3 00 39 00 39 00 S-M CH00-4 4 Skinner Standard lengde 3m. *) 2,5m stdr. 4 Channels Standard length 3m.*) 2,5m stdr. HDG SS Weight Type Art. no. Art. no. SS (kg/m) S-M CH00--00 37649 37685,75 S-M CH--00 37684 37687 0,90 S-M CH-2-00 06 37689,75 S-M CH00-3-00 Be om vår MultiGrid katalog S-M CH00-4-00 Ask for our MultiGrid catalogue Tekniske og belastningsdata på forespørsel. Technical and load capacity data available on request. T=,5 T=,5 CC T=,5 T= tykkelse / thickness in mm CC T= 6 T= 2,5 T= 5 MultiGrid opphengsystem Be om egen katalog for tekniske spesifikasjoner og belastningsdata. MultiGrid Support system Ask for separate catalogue to find technical data and safe working loads. 7 22 5 22 7 39 22 5 22 00 Distanseskive / Spacer Dobbelmonterte opphengskinner Bruk stk. M0x20mm bolt sammen med distanseskiven S-M WA-xx5 for hver 80 cm. Double mounted support channels Use one piece M0x20mm bolt together with the quadrangular spacer S-M WA-xx5 at 80 cm intervals. HDG SS Weight Type Art. no. Art. no. SS (kg/m) S-M WA-xx5 372856 37690 0,02 L 35 5 5 35 40 L 35 5 5 35 90 L 35 5 5 35 20 Tekniske og belastningsdata på forespørsel. Technical and load capacity data available on request. 55 24 Ø 8 Ø S-M WB-200-CH- S-M WB-200-CH-2 S-M WB-200-CH- T= 6 T= 6 T= 6 T= tykkelse / thickness in mm For sveisebraketter med ekstra styrke, spør etter vår katalog på MultiGrid. For welding brackets for extra heavy load, ask for our MultiGrid Catalogue. Sveisebraketter Type nr. angir L= lengde Welding Brackets Type no. state L= length Ubehandlet SS Max. Weight Type Black steel Art. no. Load (kg) SS (kg) S-M WB--CH- 37695 4.000 0,3 S-M WB-200-CH- 2 37696 4.000 0,5 S-M WB--CH00-07 3769 8.000 0,5 S-M WB-200-CH00-08 37692 8.000 0,8 S-M WB-0-CH00-09 37693 8.000,2 S-M WB--CH-2 8220* 822 8.000 0,5 S-M WB-200-CH-2 4 37698 8.000 0,9 S-M WB-0-CH-2 99 37699 8.000,3 Standard material: EN 00-S355J2. Andre kvaliteter på forespørsel. Standard material: EN 00-S355J2. Other specifications on request. 5
- 200 SPB: Kabelbaner for alle formål SPB: Cable Trays for all purposes Sammen med ETIN-klammer er banene også velegnet til instrumentrør. - 200 0-600 Together with the ETIN clamps the trays also are eminently suitable for tubing. SPBE-20: En lett bane uten dødsoner for feste av instrumentrør og kabler. Full utnyttelse av banebredden med festemuligheter helt ut i kantene. Bemerk forskjellen i hullmønster over/under 200 mm bredde. SPBE-20: A light duty tray without dead zones for mounting of tubing and cables. Full use of the tray width due to attachment facilities on the edges. Please note the different slot design up to and above 200 mm widths. SPBE-40: En bane for middels belastninger for feste av instrumentrør og kabler. Full utnyttelse av banebredden med festemuligheter helt ut i kantene. SPBE-40: A medium duty tray without dead zones for mounting of tubing and cables. Full use of tray width due to attachment facilities on edges. -2 SPB-RF: En kraftig bane for store laster. Breddene og 00 mm er velegnet til innendørs armaturoppheng. Bukket vange gir økt kapasitet, og mulighet for lengre opphengsavstander. Bemerk forskjellen i hullmønster over/under 200 mm bredde. - 200 0-600 SPB-RF: A heavy duty tray for heavy load. The widths and 00 mm are suitable for lighting installations. The return flange (RF) results in increased load capacity and support spacing. Note the different slot design for 0 mm widths and wider. Bestillingsliste / Ordering list SPBE-20 Bredder / Widths: -00--200 mm. Best. nr. angir type + vangehøyde + banebredde. Order no. state type + height of side piece + tray width. PG HDG SS AL Weight Type Art. no. Art. no. Art. no. Art. no. SS(kg/m) SPBE-20-37220 37400 37408 37227 0,9 SPBE-20-00 372203 3740 37409 37229,4 SPBE-20-372205 37402 3740 37222,9 SPBE-20-200 372207 37403 374 372223 2,4 Instrumentrør-installasjon fra Phillips Embla, Ekofisk, med doble ETIN klammer på SPBE 20. Det gir 4 rør pr. 5 cm bredde. Tubing installation from Phillips Embla, Ekofisk, with double ETIN clamps on SPBE 20. That gives 4 tubes each 5 cm width. ETIN Tubing Clamps give 60-70% overall cost savings! It pays to use the ETIN from the very first clip! Compare the ETIN clamp with all competing clamps on the market. ETIN is developed for better project economy. Front-mounting is only one of the advantages. ETIN Clamps are safe in case of fire! 6 Type OE-CB- For 4 - mm or 5/8 - pipes Type OE-CBM For 6-2mm or /4 -/2 pipes Bredder / Widths: 0-400-0-600 mm. SPBE-20-0 372209 37404 3742 3722 3,7 SPBE-20-400 3722 37405 3743 372227 4,8 SPBE-20-0 37223 37406 3744 372229 6,0 SPBE-20-600 37225 37407 3745 37223 6,9 SPBE-40 Best. nr. angir type + vangehøyde + banebredde. Order no. state type + height of side piece + tray width. HDG SS AL* Weight Type Art. no. Art. no. Art. no. SS(kg/m) SPBE-40-37740 37745 372233,3 SPBE-40-00 3774 37746 372235,9 SPBE-40-37742 37747 372237 2,3 SPBE-40-200 37743 37748 372239 2,9 SPBE-40-0 2008 37749 37224 4,0 SPBE-40-400 2009 377 372243 5,0 SPB-RF 40 and ETIN tubing clamps Be om komplette kataloger. Ask for complete catalogues.
RP = Rødprimet stål / Red oxide painted HDG = Varmgalv./ Hot Dip Galvanized SS = Rustfritt stål / Stainless Steel EN.4404 ALU = Aluminium ZP = Zinkmalt stål / Zinc painted Perforerte profiler Benyttes til diverse oppheng og feste for baner, stiger og annen utrustning. Videre til skapskinner, tavlebygging ol. Leveres i 3m lengder. Perforated Profiles For various support of trays, ladders and electrical installations. Available in lengths of 3m. 7 0 7 20 mm 5 35 7 mm 5 35 mm mm 7 0 7 Flattstål / Flat Iron Perforert på tvers / Crosswise perforated Perf. Dim. RP HDG SS ALU Weight(kg/m) dim.mm mm Art. no. Art. no. Art. no. Art. no. HDG/SS 7x20 x5 37204 372,0,, 40x5 37205 3723,4,, x4 3720 37203,7 Perforert på langs / Lengthwise perforated 7x35 x5 37207 372 379,, x5 37208 3722 3793 7873,0,, 40x5 37209 3723 37932 78229,4,, x5 3720 3724 37933,9 x35 40x5,, 40x5 8484,, x5 8485 37935,, 40x6 37984 x 40x8 37200 37202 6 mm 5 7 mm mm mm Vinkelstål / Angle Iron Perforert på tvers / Crosswise perforated Perf. Dim. RP HDG SS ALU Weight dim.mm mm Art. no. Art. no. Art. no. Art. no. HDG(kg/m) 7x6 xx3 37232 37234 37942 78228,3,, 40x40x4 37233 37240 37943 2,3 Perforert på langs / Lengthwise perforated 7x xx3 3725 3727 37939,3,, 40x40x4 3726 3728 37940 2,3,, xx3 78045 x xx5 3729 37220 3794 3,5 Perforert dobbelt på langs / Double lengthwise perforated 7x 40x40x4 37945 x xx5 78662 37946 x35 49x49x4 8234 82342 Leveres på forespørsel i eksakte lengder opp til,5m. Supplied on request in defined lengths up to,5m. 5 35 2,5 0,3 mm 28,5 7 5 5 2,5 0,3 35 36,5 5 35 5 MultiGrid L60x6 perforated system Leveres i lengder på 3m / Available in lengths of 3m. Type HDG SS Duplex* Vekt(kg/m) Single perforated Art. no. Art. no. Art. no. Weight S-M CH60-2-B-00 3743 37429 37433 5,3 Double perforated S-M CH60-2-A-00 37432 374 37434 5,3 *) Materialcode for Duplex: SAF24 Sveiseprofil for tubingklammer For rask og enkel tubing installasjon med ETIN tubingklammer. Leveres i lengder på 3m. Welding Profile for tubing clamp For quick and easy tubing installation with ETIN tubing clamp. Available in lengths of 3m. PG HDG SS ALU Vekt(kg/m) Type Art. no. Art. no. Art. no. Art. no. Weight RZ- WB 78463 78497 7
*) Low *) Low High LÅSESKRUER LOCKING BOLT SETS m/linsehode og flensmutter With pan head and flange nuts Self-Lock only in SS LÅSESKRUER LOCKING BOLTS SEKSKANTSKRUER HEXAGONAL BOLTS Lengre utgaver leveres i DIN 93 delgjenget. Longer lengths in DIN 93 partly threaded. Spisset / Cone point LINSESKRUER PAN HEAD SCREWS With Torx T BITS for torx T conical FLENSMUTTERE FLANGE NUTS Self-Lock only in SS SEKSKANTMUTTERE HEXAGONAL NUTS SKIVER WASHERS Type codes: t= Ø OD 0.5 x 20 x 2 STJERNESKIVER STAR WASHERS EKSPANSJONSBOLTER CONCRETE ANCHOR BOLTS Kvaliteter: V.G. = 5.8 Qualities: S.S. = A4-70 P.G. = 5.8 SELVBORENDE SKRUER Inntil/Up to mm stålplate/steelplate Inntil/Up to 3 mm stålplate/steelplate Inntil/Up to 3 mm stålplate/steelplate HUSK: Skruer er inkludert! REMEMBER: Screws are included! SKRUER / SCREWS TYPE STD. packs PG. HDG SS PG+HDG / SS Art. no. Art. no. Art. no. M 6 x 2 * S-M LS-NU-M6x2 200 3727 3798 M 6 x 6 * S-M LS-NU-M6x6 200 84487 M 6 x 20 * S-M LS-NU-M6x20 00 37982 M 6 x S-M LS-NU-M6x 00 372749 3736 M0 x 20 * S-M LS-NU-M0x20 00 37983 M0 x * S-M LS-NU-M0x 00 37980 84352 M0 x S-M LS-NU-M0x 37589 37362 M 6 x 2 * DIN 603 S-M LS-M6x2 200 37267 3726 M 6 x 6 * DIN 603 S-M LS-M6x6 200 84493 M 6 x DIN 603 S-M LS-M6x 200 / 00 37269 37262 M 6 x DIN 603 S-M LS-M6x 200 / 00 37360 85520 M0 x 20 * DIN 603 S-M LS-M0x20 200 / 00 37263 M0 x * DIN 603 S-M LS-M0x 00 / 372765 84352 M0 x DIN 603 S-M LS-M0x 00 / 86008 8982 M0 x 35 DIN 603 S-M LS-M0x35 00 83497 82709 M0 x DIN 603 S-M LS-M0x 89822 M0 x 70 DIN 603 S-M LS-M0x70 8396 M 6 x 2 DIN 933 S-M HE-M6x2 200 372780 M 6 x 6 DIN 933 S-M HE-M6x6 200 3727 3738 M 6 x 20 DIN 933 S-M HE-M6x20 200 37272 3739 M 6 x DIN 933 S-M HE-M6x 200 37320 M 8 x 20 DIN 933 S-M HE-M8x20 200 37 3732 M 8 x DIN 933 S-M HE-M8x 200 372 37322 M 8 x DIN 933 S-M HE-M8x 200 373 37323 M0 x 6 DIN 933 S-M HE-M0x6 00 37278 37324 M0 x 20 DIN 933 S-M HE-M0x20 200 / 00 374 373 M0 x DIN 933 S-M HE-M0x 200 / 00 375 37326 M0 x DIN 933 S-M HE-M0x 200 / 00 376 37327 M0 x 35 DIN 933 S-M HE-M0x35 00 377 37328 M0 x 45 DIN 933 S-M HE-M0x45 00 378 37329 M0 x DIN 933 S-M HE-M0x 00 379 373 M0 x 55 DIN 933 S-M HE-M0x55 00 / 37 3733 M2 x DIN 933 S-M HE-M2x 00 373 37332 M2 x 35 DIN 933 S-M HE-M2x35 00 3732 37333 M2 x 45 DIN 933 S-M HE-M2x45 00 / 3733 37334 M0 x 40 DIN 933 S-M HE-M0x40 00 3734 37335 M 6 x 6 DIN 7985 S-M PS-M6x6 200 37264 37256 M 6 x 20 DIN 7985 S-M PS-M6x20 200 372842 37257 M 6 x DIN 7985 S-M PS-M6x 200 84954 37258 M 6 x DIN 7985 S-M PS-M6x 200 37266 37259 M 6 x 40 DIN 7985 S-M PS-M6x40 00 37268 37260 Bits conical Torx T 3747 6 mm DIN 6923 S-M NU-FL-M6 200 372843 3797 8 mm DIN 6923 S-M NU-FL-M8 200 37283 37972 0 mm DIN 6923 S-M NU-FL-M0 200 372832 37280 37973 2 mm DIN 6923 S-M NU-FL-M2 200 37343 M 6 x 0 DIN 934 S-M NU-M6 00 372844 37278 M 8 x 3 DIN 934 S-M NU-M8 00 37276 37340 M0 x 7 DIN 934 S-M NU-M0 00 / 372845 3734 M2 x 9 DIN 934 S-M NU-M2 00 / 37279 37342 5x.5x.5 S-M WA-5x.5x.5 200 84394 6x2x.6 DIN S-M WA-6.4x2x.6 200 372782 6x8x.6 DIN S-M WA-6.4x8x.6 200 37275 37349 6xx.5 S-M WA-6xx.5 200 372848 373 8x6x.6 DIN S-M WA-8.4x6x.6 00 372849 37345 3735 8x40.3x.5 S-M WA-8x40.3x.5 200 84345 0.5x20x2 DIN S-M WA-0.5x20x2 00 3728 37352 2x24x2.5 DIN S-M WA-3x24x2.5 00 37346 37353 7x.4x.5 S-M WA-7x,4x,5 200 84562 x32x S-M WA-x32x 200 37354 7x35x2 S-M WA-7x35x2 200 37594 0x(29x33)x3 S-M WA-0x(29x33)x3 200 840 M 6 DIN 6798 S-M SW-M6 200 372852 37355 M 8 DIN 6798 S-M SW-M8 00 37356 M0 DIN 6798 S-M SW-M0 00 372854 37357 M2 DIN 6798 S-M SW-M2 00 37359 37358 M 6 x 40 S-M AC-6x40 00 372767 M 6 x 52 S-M AC-6x52 00 37368 M 8 x S-M AC-8x 00 372768 37369 M 8 x 60 S-M AC-8x60 00 37364 M0 x 60 S-M AC-0x60 372769 37365 37370 M0 x 85 S-M AC-0x85 37366 3737 M2 x 0 S-M AC-2x0 89823 i 00-pakn. / SELF-TAPPING SCREWS in packs of 00 4,2 x 3mm 32-PH 00 34947 4.2 x 4mm 34-PH 00 372820 4.2 x mm 36-PH 00 37282 SELVBORENDE RUSTFRIE SKRUER / SELF-TAPPING STAINLESS STEEL SCREWS For opptil 2.5mm tykkelse 4.8 x 3 mm MARUTEX M4.8x3 SS in A2 quality 00 37373 For up to 2.5mm thickness 4.8 x mm Marutex M4.8x SS in A2 quality 00 37374 Bits for Marutex Bits 37375 Maks tiltrekningsmoment / Max tightening torque for Self-Lock Flange Nuts: M6 = 8-0Nm, M8 = 20-23Nm, M0 = 40-45Nm, M2 = 80-85Nm 8 PG = 4-7 my zink. HDG = 40-70 my zink. SS = A4-70 (Hex = A4-80)
SALGSKONTORER LOCATIONS HOLDING COMPANY Øglænd lndustrier AS P.O. Box 33 NO-4358 Kleppe Tel.: + 47 5 78 8 00 Fax: + 47 5 78 8 60 Email: oglind@oglsys.no www.oglaend-system.com DATTERSELSKAP/SUBSIDIARY Norway Øglænd System AS Head office/factory P.O. Box 33 NO-4358 Kleppe Tel.: + 47 5 78 8 00 Fax: + 47 5 78 8 60 Fax sales office: + 47 5 78 8 6 Email: oglaend@oglsys.no www.oglaend-system.com Denmark Øglænd System ApS Tel.: +45 86 88 66 66 Fax.: +45 86 88 66 67 Email: oglaend-system@oglsys.dk Dubai (Middle East) Oglaend Industries Middle East Tel.: + 97 4 345986 Fax: + 97 4 345987 Mobile: + 97 55 86 83 Email: oglaendsys_me@xsmail.com Malaysia Oglaend Industries SDN BHD Tel.: + 60 3 5 922 049 Fax: + 60 3 5 922 039 Mobile: + 60 26 85 57 65 Email: sales@oglaendind.com fraser@oglaendind.com The Netherlands Oglaend System BV Tel.: + 3 804 4 204 Fax: + 3 804 9 395 Email: info@oglaend-system.nl Singapore (South East Asia) Oglaend System Singapore Pte. Ltd. Tel.: + 65 67 48 82 78 Fax: + 65 67 48 86 5 Email: oglaend.system@pacific.net.sg Sweden Ögländ System AB Tel.: + 46 (0)46 8 40 Fax: + 46 (0)46 8 45 Email: oglaend-system@oglsys.se UK Oglaend System UK Ltd. Tel.: + 44 2 552 9662 Fax: + 44 2 544 6627 Email: oglaend.system@oglsys.co.uk Korea Oglaend System Korea Co Ltd Tel.: + 82 58 320 76 Fax: + 82 58 320 762 Email: oglaend@oglaend-system.co.kr SALGSKONTORER/SALES OFFICES Norway Øglænd System AS, Division Oslo: Tel.:+ 47 22 5 0 Fax: + 47 22 2 Øglænd System AS, Division Ålesund: Tel.: + 47 70 9 09 Fax: + 47 70 9 09 5 Øglænd System AS, Division Trondheim: Tel.: + 47 73 80 99 70 Fax: + 47 73 80 99 77 AGENTER - FORHANDLERE/ AGENTS - DlSTRlBUTORS Abu Dhabi Proserv Albadie LLC Tel.: + 97 26 27 73 70 Fax: + 97 29 27 79 72 Email: proserv@emirates.net.ae www.proserv.no Australia J. T. Day Pty. Ltd. Tel.: + 6 8 93 45 33 88 Fax: + 6 8 93 45 68 Email: enquiries@jtday.com.au www.jtday.com.au Brazil M.O.TECH do Brazil Tel.: + 55 2 32 20 Fax: + 55 2 7 2437 Email: motech@motech.com.br www.motech.com.br Brunei Shinba Integrated Engineering Services Tel.: + 673 333-489 Fax: + 675 333-6333 Email: info@shinbaies.com Canada Apel/CSA Enterprises Tel.: + 902 4 5647 Fax: + 902 4 5286 Email: urquhart@csarep.com www.csarep.com Finland Elmarino - Shipping OY Tel.: + 358 22 54 6 00 Fax: + 358 22 54 62 76 Finn H&T Group Oy Tel.: +358 45 6 4004 Fax: +358 3 575 Email: teppo.kuivanen@finnhtgroup.fi www.finnhtgroup.fi lndonesia PT. Multi Tarex MuIia Tel.: + 62 2 3983 5337 Fax: + 62 2 3983 5340 Email: agus@multitarex.co.id www.multitarex.com Italy Ecis Group Tel.:+39 039 2788 Fax +39 039 278353 E-mail: seco@ecisgroup.it www.ecisgroup.it Malaysia Esteem Link (Letrik Utama) SND BHD Tel.: + 60 6 85 47 2, 4 580 Fax: + 60 6 85 44 352 Email: ellusb@tm.net.my Russia (St. Petersburg) Newtech Ltd Tel.: +7(82) 702 3 38 Fax: +7(82) 702 80 52, 42 70 73 Email: very@newtech-sp.ru www.newtech-sp.ru Thailand Probity International Co Ltd. Tel.: + 66 2 70 646 Ext. 07 Fax: + 66 2 70 647 Email: ak@probity.co.th www.probity.co.th USA (Texas and Louisiana) Source lec Tel.: + 28 882 80 Fax: + 28 882-85 Email: bob.johnson@sourceiec.com www.sourceiec.com Vietnam MT Corporatin Tel.: + 848 82 0373 Fax: + 848 82 0358 Email: mail@mt-co.com Iceland Smith & Norland Tel.: + 354 52 03 000 Fax: + 354 52 03 0 Email: sminor@sminor.is www.sminor.is * X X X * X HEAD OFFICE AND FACTORY SUBSIDIARIES AGENTS DISTRIBUTORS SALES OFFICES FABRICATION FACILITIES 9
MultiGrid for ship SIMPLY THE BEST! Dette har vært vårt motto helt siden firmaet ble grunnlagt i 977. Ved å følge dette mottoet har vi blitt markedslederen innen våre felt globalt. Øglænd Systems mål er å utvikle systemer som er de beste, enkleste og mest økonomiske på markedet. This has been our motto since the company was founded in 977. By living up to the motto we have become the market leader in our field worldwide. Oglaend System s goal is to develop systems that are better, simpler and more economic overall. Konsern/Holding company: Øglænd Industrier AS Datterselskap/Subsidiary: Øglænd System AS Hovedkontor fabrikk/head Office factory: P.O. box 33, NO-4358 Kleppe, Tel.: +47 5 78 8 00, Fax: (47) 5 78 8 60 Fax sales office: +47 5 78 8 6 ADS. 20 www.oglaend-system.com Email: oglaend@oglsys.no 06.0