GRUPPE 6 ADR skilt... 6.2 ADR utstyr... 6.7 Surrekroker... 6.11 Lastesikring... 6.16 Containerutstyr... 6.25 Støttebein... 6.33 Drag og utstyr... 6.35 Kulekranser... 6.47 Hurtiglåser... 6.48 Kantprofiler... 6.49 Edbro tippsylinder... 6.51 Tilbehør Edbro... 6.66 Tipphengsler... 6.67 6.1
ADR SKILT 650000 650035 8901 Fareskilt komplett rustfri ramme m/39 tall og overtrekk 89015 Tallplater for 8901, 39 stk. 650001 650018 89023-P1270 ADR-skilt sammenleggbart 400 x 300mm 89067 ADR-skilt sammenleggbart 300 x 120mm 650002 89021 ADR-skilt sammenleggbart u/hengsler (laminat) vertikalt 400 x 300mm 650003 8902 ADR-skilt sammenleggbart m/bøyle 400x300mm 6.2
ADR SKILT 650030 89011 Fareskilt ramme til løse siffer 650084 650059 650086 8908-P1267 Skiltholder 400 x 300mm m/lås sort 890805 Skilteholder rustfri 400x300mm m/lås Skiltholder 300 x 120mm m/lås sort 650005 650017 650006 650007 650038 8906-P1268 ADR-skiltplate alu 400 x 300mm 89065 ADR-skiltplate alu 300 x 120mm 89061 Selvkleb. ADR-skilt 400 x 300mm 89062 Magnetskilt ADR 400 x 300mm 89066 Magnetskilt ADR 300 x 120mm 650008 650009 89024 Vrider liten cc 23mm 89025 Vrider stor cc 32mm 6.3
ADR SKILT 650010 650011 650012 650013 650014 650015 650060 650061 650075 650077 650078 650081 8940 ADR-skilt Gass 23/1965 8942 ADR-skilt Ammoniakk 268/1005 8943 ADR-skilt Bensin 33/1203 8944 ADR-skilt Parafin 30/1223 8945 ADR-skilt Fyringsolje 30/1202 8947 ADR-skilt Flybensin 30/1863 89451 ADR skilt Aluminiumsmelte biprodukt 423/3170 89459 ADR-skilt Diesel/Fyringsolje/Bensin 30/1202-33/1203 ADR-skilt Argon 22/1951 ADR-skilt Metan 223/1972 ADR-skilt Oppvarmet flytende stoff 99/3257 ADR-skilt Nitrogen 22/1977 Alle skilt har målene 400x300 mm 650020 8909 Talrammeholder rustfri 650036 89016 Overtrekk skilt 650051 8926 Dokumentmappe 400x260mm 6.4
ADR SKILT 650080 89083 Skiltholder 250x 250mm galv. m/lås 651002 89084 Skiltplate 250x250mm galv. 650082 89081 Skiltholder 300x300mm galv. m/lås 651004 89082 Skiltplate 300x300mm galv. 651100 Skiltplate 300x300mm syrefast 651101 Skiltholder 300x300mm syrefast 6.5
ADR SKILT Fareseddler til landeveistransport (ADR) og jernbanetransport (RID). 250 x 250mm om ikke annet angitt. 651040 651013 651014 651041 651015 651016 651019 651020 621021 651022 651023 651024 651025 651026 651027 651029 651030 651031 651032 651033 651034 651035 651036 651039 651063 Farekl. nr. Beskrivelse F 1007 Eksplosjonsfare 300 x 300mm F 0100 1 Eksplosjonsfare 1.1D 250x250mm F 0140 1,4 Eksplosjonsfarlig 1.4 F 01401 1.4 Eksplosjonsfarlig 1.4G F 114S 1.4S Eksplosjonsfarlig, 1.4S, 100 x 100mm F 0150 1.5 Eksplosjonsfare 1.5 F 0210 2.1 Brannfarlig gass 2.1 F 0220 2.2 Ikke brannfarlig og ikke-giftig luftarter F 0230 2.3 Giftig gass F 0300 3 Brannfarlig væske F 0410 4.1 Brannfarlig fast stoff F 0420 4.2 Selvantenning F 0430 4.3 Utvikler antennelig luftart ved berøring med vann F 0510 5.1 Oksiderende stoffer 5.1 F 0520 5.2 Organisk peroxid brannfarlig F 0610 6.1 Giftig F 0620 6.2 Smittefarlig F 07B0 7B Radioaktivt stoff i kolli tilhører kategorien II-Gul F 07A0 7A Radioaktivt stoff i kolli tilhører kategorien I-Hvit F 07C0 7C Radioaktivt stoff i kolli tilhører kategorien II-Gul F 07D0 7D Radioaktive stoffer anvendes på vogner og containere F 0800 8 Etsende F 0900 9 Forskjellige farlige stoffer F 0125 9 Temperatur 10 Miljøfarlige stoffer 1 1.4 2.1 2.2 2.3 3 4.1 4.2 4.3 5.1 5.2 6.1 6.2 7.A 7.B/7.C 7D 8 9 6.6 9 10
ADR UTSTYR 652001 8949N Pulverslukker 2 kg 652008 652100 J-EXT6KG Pulverslukker 6 kg 27A183B Høyde 550 mm Dia. 150 mm Nettovekt 9,3 kg Pulverslukkersett 6 kg pulverslukker og kasse 652008 + 653003 652014 533 Holder for 6 kg apparat - sort 652012 8952 Overtrekk brannslukker 6.7
ADR UTSTYR 653001 JBFR65 Kasse for brannslukker 6 kg m/topplokk 260x700 mm 653003 653007 JBWE70 JBXE83 Kasse for brannslukker 6 kg 700 x 300 x 253mm Kasse for brannslukker 12 kg 830 x 310 x 263mm 653004 Glasfiberkasse for brannslukker 6 kg, glassfiber 660 x 270 x 190mm. Leveres uten merkning. 683730 683732 Kasse for 1 stk. brannslukker Mix sidehengslet 280x600x220 mm Sjøvannsbestandig aluminium og lokk i rustfritt polert stål Nettovekt: 7,45 kg Kasse for 2 stk. brannslukkere Mix sidehengslet 480x600x220 mm Sjøvannsbestandig aluminium og lokk i rustfritt polert stål Nettovekt: 10,76 kg 6.8
ADR UTSTYR 654012 Brannslukker-logo, selvklebende 60x80 mm 654047 654048 654049 654050 654051 654052 ADR håndskuffe hvit plast ADR plastskuffe sort Absorberingsmiddel 7 kg. sekk Plastbøtte 10 l. inkl. 1,5kg. absorberingsmiddel Absorberingsmatte 400x500mm. Absorberingsevne 1,5 l. Komplett absorberingssett. Inneholder 654047, 654048, 654050 og 654051. 651005 8537 Nødhammer med holder 6.9
ADR UTSTYR 654000 654001 654033 654004 654005 654025 653019 654008 654009 654026 654029 651005 89562-516 ADR-bag m/gnistfrie lamper 89563 ADR-bag m/varseltrekanter 89542 3M Sikkerhetsmaske 4279 80981-AHL444 Varselblinklykt gnistfri ulo 89575 Varseltrekant 890551 ADR-bag u/innhold ADR-håndlykt gnistfri/vanntett, gul 89557 Refleksvest kl 2 89556 Øyeskylleflaske 89552 PVC-handsker 89555 Kjemikaliebriller 8537 Nødhammer m/holder (vedr. 654000 og 654001): ADR-bag inneholder følgende: 1 par PVC-hansker 1 par beskyttelsesbriller 1 stk. øyeskylleflaske 1 stk. 3M sikkerhetsmaske 1 stk. refleksvest 1 stk. gnistfri håndlykt m/batterier 2 stk. varselblinklykt m/10 stk. batterier eller 2 stk. varseltrekanter 6.10
SURREKROKER 660000 511 Surrekrok nedfelt med D-ring. 6000kg 90x90x29mm Vekt: 0,90kg 660001 512 Surrekrok 10 tonn 120x60x120mm Vekt: 2,23kg 660003 70631 Surrekrok rund 8000kg Ø64mm Vekt: 1,00kg 660221 70632 Surrekrok V114 kvadratisk 8000kg 68x65x113mm Vekt: 1,15kg 6.11
SURREKROKER 660005 80603 Surrekrok for sveising 6000kg 87x11mm Vekt: 0,35kg 660006 80605 Surrekrok innvendig 6000kg 90x90x29mm Vekt: 1,15kg 660007 7065 Surrekrok, 4 hull 6mm bolt, 1000kg 8mm bolt, 1800kg 102x95x25mm Vekt: 0,45 65 660008 70675 Surrekrok med skål i alu. Bolt med 16mm gj. 2000 kg. Største diam. Ø90mm Vekt: 0,05kg 30 4 Ø9 Aluskål 55 145 M16 6.12
A - bare bedre løsninger SURREKROKER 660009 7066 Surrekrok 2000kg 150x115x23mm Vekt: 0,75kg Tværsnit A-A 22 2 Ø80 660010 70672 Surrekrok 800kg Ø120x22mm Vekt: 0,25kg 4stk Ø5 A Ø6 Ø6 100 120 660011 7064 Surrekrok 6500kg 150x40x100mm Vekt: 1,90kg 10 Ø13 660012 7068 Surrekrok 8000kg 65x31x105mm Vekt: 0,70kg 105 40 170 4 31 65 6.13
SURREKROKER 10 Ø13 660146 70682 Surrekrok 7500kg Vekt: 0,9kg Passer for alu. Kantprofil 352001 105 40 R4. 20 10 28 85 170 4 3 65 104 145 660013 7050 Ferjekrok 20 tonn 132,5x130 Ring Ø20x30 Vekt: 1,9 kg 660224 780615 Surrekrok nedfellbar 6000 kg 100x125x40 mm Vekt: 1,55 kg 37 660142 70625 Surrekrok 4300 kg 150 x 67 x 37 mm Vekt: 1,8 kg 150 67 6.14
SURREKROKER 660254 Bindering alu-skål, stålring 2500 kg Ø92 x 24 mm Vekt: 0,35 kg 660256 Bindering tett bunn alu-skål, stålring 4000 kg Ø92 x 23 mm Vekt: 0,44 kg 660255 Bolt for bindering 660256 12 x 140 mm undersenket Vekt: 0,125 kg 660300 Surringsring 5000 kg Ø10 Rustfri 660302 Surringsring nedfellbar 10 tonn Rå utf. 6.15
LASTESIKRING 698014 698015 AG-3A AG-3 Kantbeskytter plast190x190x20 6,0 m - Orange Kantbeskytter plast120x120x15 5,9 m - Blå 660244 Kantbeskytter til 50mm bånd dim. 85x120x125 660025 660029 660026 7090 Veggskinne universal, galv., gullchrom 3m 7092 Veggskinne universal, alu. 3m 7093 Plastendestykke for 660025/660029 660028 70901 Veggskinne universal flat 3,05 m, galvanisert 6.16
LASTESIKRING 660163 7084 Rund teleskopsperrebom/20mm for hullskinne/universalskinne, justerbar og fjærbelastet. Lengde 2215-2600 mm Maks. belastning ca. 375 kg Vekt: 8,0 kg 660163 660159 7082 Firkantet teleskopsperrebom/20mm i galv. stål for hullskinne/universalskinne, justerbar og fjærbelastet. Lengde 2150-2640 mm. Maks. belastning ca. 400 kg Vekt: 8,5 kg 660159 660027 660155 660156 660030 7080 Skinne galv.plate 20 mm hull 70801 Hullskinne som 660027, med 25 mm hull Høyde: 11 mm 70802 Hullskinne som 660027, med 25 mm hull Høyde: 15 mm 70803 Endestykke 68 mm for 660027 og 660167 660165 70844 Rund teleskopsperrebom/25 mm 6.17
LASTESIKRING 660166 660167 7085 Konfeksjonsstang krom 7086 Veggskinne for konfeksjonsstang 660166 660040 660113 660043 660044 660016 032013 Lastesikring 4m m/kroker 500kg. Båndbredde 25mm 7021 Lastesikring 6m m/kroker 2500kg. Båndbredde 35mm 030134 Lastesikring 10m m/kroker m/sperreleppe 4000kg. 70302 Lastesikring 10 m m/kroker 4000kg. SU410EK Lastesikring 10 m u/kroker(ekeri) 4000kg. 660108 660109 70201 Skapsurring 2000kg 1+3 m/sl beslag 45mm 70202 Skapsurring 2000kg 1+4 m/sl beslag 50mm 660243 Rullebånd med automatisk innrullning 0,5+2,5m 6.18
LASTESIKRING 698086 Bolt for Ekeri stropper 670199 SUHK10 Hurtigsurring m/kamlås 1,0m sort 598129 Forlengerhåndtak til strammer 660125 660111 7031 Surringsstrammer lang 50 mm bånd 032106 Surringsstrammer kort 50mm bånd. 6.19
LASTESIKRING 698020 Roll-up 698032 601150 Bremsekloss for Jekketralle kunststoff 660050 660051 660052 660053 660054 660056 660057 96084 8mm kortlenk gr80 4 mtr 96086 8mm kortlenk gr80 6 mtr 96104 10mm kortlenk gr80 4 mtr 96106 10mm kortlenk gr80 6 mtr 96108 10mm kortlenk gr80 8 mtr LE0810 Lebus 8710 kg for 8 og 10 mm LE1013 Lebus 15130 kg for 10 og 13 mm 660060 660061 670193 660062 660063 660064 660065 698003 801302 Sperrebom. Firkant 2300-3200 mm 801363 Sperrebom. Firkant 2350-3350 mm, gassdrevet 801362 Sperrebom gassdrevet 1900-2500 mm 801324 Rasbøyle for sperrebom. Firkant 801311 Toppfot til 660060 801312 Bunnfot til 660060 801326 Kompl. hus for 660060 Fjær og pal for 660060 660060 660061 6.20
LASTESIKRING 660067 7095 Firkantet lastebom alu, 2340-2630 mm Maks. belastning 1000 kg Vekt 8 kg 660068 7097 Sperrebom alu-rør 42 / 31 mm 2350-3200 mm Vekt 5,5 kg 660070 7099 Sperrebom alu m/justerbar låsing 2400-2750 mm Vekt 11,1 kg 660134 7040 Lastestrammer 6 tonn u/bånd 660138 Laststrammer 95mm u/bånd 660141 Nøkkel/skralle for laststrammer 28mm 6.21
LASTESIKRING 660222 660080 660230 698017 660227 80150 Autonordic strammer m/10m bånd Slitestyrke 5 tonn 80150 Høyre Autonordic strammer u/bånd 80150 Venstre Autonordic strammer u/bånd 780105 Sveiv/håndtak reserve for 80150 80151 Reservesplint for bånd 660082 80034 Mont.brakett lav 660083 80035 Mont.brakett lav sveises 660084 80075 Spennstang m/skralle 6.22
LASTESIKRING 660085 80114 Låsebolt for bånd kantprofil 660086 80115 Spennstang for 80150 660093 80056 Planbeslag for båndgjennomføring 660087 660089 80050 Bånd 10M Grønt 3 x Slitestyrke 5 tonn 80060 Bånd 10M Grønt 3 x Slitestyrke 6 tonn 6.23
LASTESIKRING 660091 660092 660257 660225 80050or Bånd 10M Orange m/triangel og øye 5 tonn 80052or Bånd 12M Orange m/triangell og øye 5 tonn 10152-99 Bånd 9.5M Orange m/krok og øye 5 tonn Bånd 9.5M Blått m/krok 4 tonn 6.24
CONTAINERUTSTYR Containerbanker L M X F y 1200 529 48 980 639 45 600 829 34 mm mm kn 700000 410.075.000 Containerbanke CH 05 160A med integrert containerlås. Type CV 05 105A, alle containerlåsdeler er galvanisert. Vekt ca. 70 kg LM = X = FV = Rammebredde i mm Overheng fra rammebredde til senter containerlås Belastning i KN. 1. KN = 107, 252 kg.. L M X F y 1200 529 70 980 639 65 600 829 51 mm mm kn 700001 410.080.000 Containerbanke CH 05 200A med integrert containerlås. Type SV 05 10A, alle containerlåsdeler er galvanisert. Vekt ca. 80 kg 6.25
CONTAINERUTSTYR Containerbanker med styreruller L M X F y 1200 529 48 980 639 45 600 829 34 mm mm kn 700002 410 078 000 Containerbanke med 2 stk styreruller og holdere Vekt ca. 88 kg. L M X F y 1200 529 70 980 639 65 600 829 51 mm mm kn 700003 6.26 410 088 000 Containerbanke med 2 stk styreruller og holdere Vekt ca. 96 kg
CONTAINERUTSTYR 798174 410 078 750 Containerbanke dobbel for 745 og 782 container, cc mellom låser er 185 mm 6.27
CONTAINERUTSTYR Reservedeler for Containerbanker 410.075.000 og 410.080.000 410.078.000 og 410.088.000 410.078.750 Pos.No. 700008 700009 700010 700011 700012 700013 700014 905 159 002 Bolt for fallsikring 10 905 199 001 Fallsikring for containerlås 11 905 000 276 Tapp, låsebolt 52 mm 2 905 000 273 Foring, låsestyring indre 52 mm 3 905 000 274 Ytre lager for containerlås 52 mm 4 905 000 275 Mutter for containerlås 52mm 6 905 000 187 Sikringsring 7 6.28
CONTAINERUTSTYR Schneider Containerlås 10 120 175 180 22 150 ø38 700020 905 248 000 Containerlås med 38 mm bolt etter iso - containerchassis og vekselflak med 120 mm bakplate, helt nedsenkbar. Alle låsedeler er galvanisert. Vekt ca. 11 kg. 700021 905 237 000 Containerlås med 52 mm bolt etter iso - containerchassis og vekselflak med 140 mm bakplate, helt nedsenkbar. Alle låsedeler er galvanisert. Vekt 11,6 kg. 700105 700106 700107 700108 700110 798071 905 000 127 Mutter for 38 mm bolt 905 000 137 Skrue 38 mm 905 000 177 Ytre lager 38mm 905 000 178 Foring, låsestyring indre 38mm 905 000 190 Låsering 38 mm 905 000 077 Mutter for containerlås, flat 38 mm ø100 ø85 80 700030 700031 700111 700101 700102 640 003 110 Styrerull stål for ER85 640 003 125 Styrerull stål for ER100 640 003 112 Orepinne for 700030/700031 905 000 001 Monteringsverktøy sikringsring 52 mm 905 000 002 Monteringsverktøy sikringsring 38 mm B A 14 ø13 ø40 6.29
CONTAINERUTSTYR 700032 405 000 025 Holder for styrerull 700114 905 195 100 Containerhjørne sveiset 700043 72999 Lastvekslerlås 80mm syl. Res.deler: 125031 syl. 61M-2P-080 A-0100 125127 Stempelstangmutter 700200 Tr.fjær 3mm L=300mm (2 stk) 700207 Mansjett 700041 71999 Lastvekslerlås nedfellbar Res.deler: 125001 Syl 61M-2P-063 A-160+48 125071 Gaffelfeste 700204 Tr.fjær 5mm 280mm 798181 Låsekrok 798107 Bolt for innv. mek. 16mm 798177 Bolt for utv. mek. 20mm 6.30
CONTAINERUTSTYR 798002 Lås for lastvekslerlås Nr.1 798003 Lås for lastvekslerlås, lang Nr.2 Fjærlås A mål B mål Type 700070 700071 700072 700073 700129 640 001 005 Fjærlås 18 mm 20 mm SF 1820 640 002 005 20 mm 20 mm SF 2020 640 012 005 28 mm 20 mm SF 2820 640 020 018 Bolt for fjærlås 18 mm Bolt for fjærlås 20 mm 6.31
CONTAINERUTSTYR Schneider Støttebein Telematic ( patentert ) Schneider Støttebein med Telematic, som gjør betjeningen av teleskopet automatisk i teleskopdelen. Støttebeinene har de nødvendige sertifikater DIN EN 284, og SERTIFIKAT bga-v 92 108. De er også godkjent gjennom salttest etter 240 std. Teleskopdelene er galvaniserte. 1. Betjeningsknapp nedtrykkes mot bunnplate. 2. Teleskoper i ønsket stilling. 3. Betjeningsknapp låses. 700050 700086 700087 700118 700100 700109 644 135 360 Støttebein telematic 18 tonn A2 SB 4118 Avsettingshøyder 1130/1180/1230/1280/1330/1380/1430 ca 44 kg 640 110 085 Støtte u/brems 775/460 mm 640 110 100 Støtte m/brems 775/500 mm 640 111 110 Lagerforing for støtte m/brems 640 000 002 Monteringsverktøy til sikringsring støtte 640 003 008 Sikringsring til støtte støttebein 700060 640 116 000 Lager 250mm m/plate OBS! Høyre og venstre modell 700062 640 001 079 Holder enkel 6.32
STØTTEBEIN 710000 710 Støttebein med plate Total lengde 750 mm Diameter 70 mm Løftehøyde 470 mm Belastning 4000 kg. vekt 19 kg. 710001 711 Festeklemme svingbar 710002 712 Festeklemme fast 710003 710004 810 Støttebein for kjerre m/ platefot Løftehøyde 450 mm Løftekapasitet 5000 kg. Statisk belastning 10 000 kg. Vekt 30 kg. 811 Støttebein for kjerre m/ rullefot Løftehøyde 450 mm Løftekapasitet 5000 kg. Statisk belastning 10 000 kg. Vekt 30 kg. 6.33
STØTTEBEIN 235151 710013 LGA7CM1 Støtteben, forsterket 870 440 24t 24t 95kg JSU03 Sveiv for støttebein Jost/Orlandi 6.34
DRAG OG UTSTYR Manuelle boltede drag 735529 Trekkstang for GZV, boltet 1820mm m/vbg 57,5mm 6.35
DRAG OG UTSTYR Deler til manuelt drag fra april 2000. Prod.nr 20001 - Dragstrang 70X190 mm 732021 M18x60 M 18 x 60 mm skrue m/skive og mutter, 6 stk. Sveiseinstruksjon for tilhengerens dragfester. For at våre drag skal godkjennes etter VTI enl. SS3635 må følgende instruksjon følges : 1. Sveisetverrsnitt : A 5 2. Sveiseelektrode : OK 48.00 eller tilsvarende 3. Skal være helsveiset Sveiseinstruksjon for innfestning av gaffelfester i drag 1. Sveisetverrsnitt : A 5 2. Sveiseelektrode : OK 48.00 eller tilsvarende 3. Skal være helsveiset. For alle drag som leveres med løse gaffelfester må disse instruksjonene etterleves. Sveisingen kan kun utføres av autoriserte verksteder/påbyggere som er godkjente til å utføre sveisearbeider. Bevola Norge AS står ikke ansvarlig for sveisearbeid som ikke Bevola har utført. 6.36
DRAG OG UTSTYR B1, D190kN Maks draglengde ved framvogn belastning Triangel lengde Korteste draglengde 10 tonn 16 tonn 18 tonn 20 tonn 540mm 1300 2800 2150 1950 1800 740mm 1500 3100 2450 2250 2050 1040mm 1800 3400 2900 2650 2500 1290mm 2050 3650 3250 3000 2850 1590mm 2350 3950 3750 3450 3250 B2, D190kN Maks draglengde ved framvognbelastning Triangel lengde Korteste draglengde 10 tonn 16 tonn 18 tonn 20 tonn 540mm 1300 3300 3300 3300 3300 740mm 1500 3500 3500 3500 3500 1040mm 1800 3800 3800 3800 3800 1290mm 2050 4050 4050 4050 4050 1590mm 2350 4350 4350 4350 4350 1. Eu godkjent nr.94/20 EG 2. D-verdi 190KN 3. Framvogn 20 tonn (boggi) 4. Lengderegulering etter ønske 5. CC-mål 980,1100, 1200 0g 1300 6. Lav vekt ca. 140 kg. 7. Ingen formontering 8. Alt. trekkøye og innfestning bak 735400 Komplett dragstang 1600 mm, trekkøye 57 mm 735401 Komplett dragstang 1900 mm, trekkøye 57 mm 735402 Komplett dragstang 2400 mm, trekkøye 57 mm 735508 Komplett dragstang B2 2800 mm, trekkøye 57 mm 735111 Tillegg ekstra hull 70 mm 735596 Dragstang komplett m/konisk foring 1600 mm, trekkøye 57 mm 735597 Dragstang komplett m/konisk foring 1900 mm, trekkøye 57 mm 735598 Dragstang komplett m/konisk foring 2400 mm, trekkøye 57 mm 735599 Dragstang komplett m/konisk foring 1800 mm, trekkøye 57 mm 731035 A99 Tillegg ekstra hull 180/190 mm konisk Luftoperert drag. 6.37
DRAG OG UTSTYR Vedlikehold av luftoperert drag og luftsylinder 731100 NB! Max lufttrykk 8 bar. Slakk mellom dragstang og styring i triangel: Sideveis juster ved å løsne M24 kontramutter og juster med M24 unbrakoskrue. Opp/ned justeres ved å løsne M20 kontramutter og juster med M20 unbrakoskruer. NB! Det skal være ca. 1-2 mm klaring mellom dragstang og styring i triangel. Slakk i lengderetning av dragstang: Skift foring pos. 19 i dragstang, om nødvendig kan foring pos. 17 også skiftes. Stempel pos. 11 kan også skiftes, se fremgangsmåte ved demontering/montering av luftsylinder. Reparasjon av luftsylinder: Om luftlekkasje oppstår er det 2 muligheter, gummibelg pos. 3 eller o-ring pos. 8 er defekt. Demonter 4 stk. skruer pos. 15, løft opp luftsylinderen, sett luft på sylindertopp så stempelet kommer i låst posisjon (ute). Demonter låsemutter pos.12, spesiell fjærskive pos. 13 og skiver pos. 24. Stempel pos. 11 og fjær pos. 9 kan nå taes ut. Neste operasjon blir å demontere sylindertopp pos. 1 (6 stk. M8x30). Trekk ut stempelstang pos. 10 med gummibelg pos.3. O-ring pos. 8 kan nå skiftes. Ved skifte av gummibelg pos. 3, skru fast stempelstang pos.10 med loctite, hold fast stempelstangen på en slik måte at det ikke blir skader i overflaten. Sett hylse pos. 7, og stempelstang pos. 10 inn med fett og monter i motsatt rekkefølge som demontering. NB! Mutter pos. 12 trekkes til og løsnes med 1/2 omdreining så stempel pos. 11 kan beveges. Deler for luftoperert drag Type GZLV e4 94/20*2202*01 D190kN B1 og GZLV e4 94/20*2202*01 D190kN B2: 734112 Glideplate side 95x80mm 2stk. pr. drag Glideplate foran 185x100mm 1stk. pr. drag Glideplate over syl. 170x50mm 2stk. pr. drag 6.38
DRAG OG UTSTYR Deler for luftsylindere fra Januar 2002 Stempel ut av hus: Inne: 29 mm Ute: 88 mm Låsesylinder for drag 731100 Låsesylinder for kjerre 731100 Pos Del Antall Delenr. Pos Del Antall Delenr. 1 Sylinder topp 1 731114 13 Fjærskive spes. 12 mm 1 731126 2 Sylinder hus 1 731115 14 Skrue M8x25 m/ låsemutter 6 731127 3 Gummibelg 1 731116 15 Skrue M12x30 m/låsemutter 4 731128 4 Øvre skive 1 731117 16 Boss øvre for slepvogn 1 731129 5 Nedre skive 1 731118 17 Foring øvre for slepvogn 1 731130 6 Senkhodeskrue M12x25 1 731119 17.1 Foring øvre for kjerre 1 798019 7 Hylse 1 731120 18 Boss for dragstang slepvogn - 731131 8 O-ring 1 731121 19 Foring for dragstang slepvogn - 731132 9 Fjær 1 731122 20 Boss kon nede slepvogn 1 731133 10 Stempelstang 1 731123 21 Boss øvre for kjerre 1 731134 11 Stempel 1 731124 22 Boss kon for kjerre - 731135 12 Låsemutter M12 1 731125 23 Mellomplate 16 mm for kjerre 1 731136 798027 798028 Lås for 731100 Rep.sett for 731100 Pos. 3,4,5,6,8,10,12 og 13 Deler til luftoperert drag fra januar 2002 Art. nr. 731100 735120 731061 731062 735121 735122 731064 731065 735102 Beskrivelse luftsylinder komplett 70mm Glideplate side 95x80mm 2stk.pr.drag 24 mm spennstift 24 mm kontramutter Glideplate foran 185x100mm 1stk.pr.drag Glideplate ved syl. 170x40mm 2stk.pr.drag 20 mm spennstift 20 mm kontramutter Plastplugg Ø 70mm for foring låsebolt Ant. 1 2 2 2 1 2 6 6 1 6.39
DRAG OG UTSTYR Deler for luftsylindere fra april 2000 731080 3022-BI 731051 3123 731052 3124 731053 3125 731054 3126 731081 3022-BII 731082 3022-B3 731084 3022-B5 731085 3022-B6 731055 3127 731090 3024-P5 731088 3024-P3 731089 3024-P4 731092 3013-PI 731091 3013-P2 731095 3020-P2 731094 3020-P3 731056 3128 Sylinder for drag 731030 3002C Identifisering: Pos 5 er en 14 mm skrue Nøkkelvidde 22 mm Sylinder for kjerre 731030 3002C Pos Del Antall 1 Lokk, 8 mm for sylinder 1 2 Sylinderhus 1 3 Styring for låsebolt 1 4 O-ring 29,74 x 3,53 1 5 M14 x 30 med skive og o-ring 1 6 M8 x 20 skrue 4 7 Trykkfjær 1 8 Luftbelg med ringer 1 9 M8 x 20 skrue med forsenket hode 4 10 Låsebolt for 3002 C 1 11 Foring herdet for drag/kjerre 1 12 Boss rett for slepvogn 1 13 Boss kon for drag og kjerre - 14 Mellomplate for 3002 C 1 15 Boss rett for kjerre 1 16 Styring for 3002 D, H = 40 mm 1 17 Boss ovalt for 3002 D 1 18 Låsebolt for 3002 D 1 Sylinder for uttrekkbar semi 731030 3002D 731030 731060 731061 731062 731063 731064 731065 Deler til luftoperert drag fra april 2000 Prod.nr 10001 Beskrivelse 3002C luftsylinder komplett 3016-B4 Glideplate sider 80x70mm 3016-B1 24 mm spennstift 3016-B2 24 mm kontramutter 3016-B10 Glideplate under 180x80mm 3016-B11 20 mm spennstift 3016-B12 20 mm kontramutter Ant. 1 2 2 2 2 4 4 6.40
DRAG OG UTSTYR 734100 731 Dragfeste 734103 0132.160 32mm bolt m/ smørespor og krone mutter 734104 0132.155 32 mm bolt med låsemutter 770060 AT 20007 Sveiseboss uten spor 770059 AT 20006 Sveiseboss med spor 6.41
DRAG OG UTSTYR Boss for draginnfestinger 734112 Vibrablokk foring Ø32 x 60 x 102 mm Stål - gummi Til drag merket Regensburger (fra mars -03) 735112 Messingforing Ø32 x 38 x 100 mm Boltede drag m/knekk 734102 733 Vibrablokk foring Ø32 x 60,5 x 103 mm Stål - gummi - stål 770015 173 500 021 Dragfeste m/kon fra begge sider, Briab 6.42
DRAG OG UTSTYR 734120 890 403 010 Briab bæreaksel 734122 890 402 030 Briab skive 734123 890 402 041 Briab bolt 27 mm m/mutter 734121 890 402 020 Kon foring Briab 6.43
DRAG OG UTSTYR Reservedeler til drag med knekk Alt. 1: Fra august 2004 Reservedelspakke for boltet AT-Drag Antall Varenummer Beskrivelse 4 798024 Foring ytre 50x60,4x101mm 4 798023 Foring indre rustfri 32x45x102 mm 4 734104 Dragbolt 0132.155 8 798022 Selvsmørende foring 45x50x50 mm 798024 798023 798022 Alt. 2: Til mars/april 2003 Reservedelspakke for drag med bronsjeforing 58,4x32 mm 734004/05/15/25/35 Antall Varenummer Beskrivelse 4 798025 Foring ytre 50x58,4x101mm 4 798023 Foring indre rustfri 32x45x102 mm 4 734104 Drag bolt 0132.155 8 798022 Selvsmørende foring 45x50x50 mm 798025 798023 798022 Alt. 3: Fra mars til august 2004 Reservedelspakke for drag med messingforing 38x32x100 mm 734040/41/42 Antall Varenummer Beskrivelse 4 735112 Messingforing 38x32x100 mm 4 734103 Drag bolt med smørespor 735112 6.44
DRAG OG UTSTYR 735100 735101 Gaffelfeste med vibrablokk Gaffelfeste med messingforing 734108 735 Gaffelfeste briab 734109 734110 90.512-00 Dragopphengsfjær 5/8 Strekkfisk 735527 Gaffelfeste for smørefri foring 6.45
DRAG OG UTSTYR 734131 3346 Parksveiv 720004 Kz1012 Kingpin 2 for 12mm plate 720006 Kingpin 3,5 for 16mm plate 720007 Kingpin 2 for 16mm plate 6.46
KULEKRANSER Svingkrans 740000 740002 740012 220120 Svingkrans 90/1100.20, akselbelastning 11 tonn, egenvekt 71 kg 90/1100. 24 Svingkrans 90/1100.24, akselbelastning 18 tonn, ved 2 aksler. 16 tonn ved mer enn 2 aksler egenvekt 71 kg 90/1200.22 Svingkrans 90/1200.22, akselbelastning 16 tonn, egenvekt 79 kg A B C D E F G H Ød Egenvekt Art.nr. mm mm mm mm mm mm mm mm mm Ca. kg 740000 1100 1108 985 964 1060 1074 10 90 18 71 740002 1100 1108 985 954 1060 1074 10 90 18 71 740012 1200 1208 1085 1054 1160 1174 10 90 18 79 6.47
HURTIGLÅSER NB! Sjekk bilfabrikkens påbyggs-anvisning med hensyn til dimensjoner på hjelperamme og boltdimensjoner. Kranlås 1 1 3 2 Opp til 32 t/m v/4 stk låser 760000 760001 760002 610015 8120 Pos1 Kranlås overdel 8121 Pos2 Kranlås underdel 8125 Pos3 Bolt for 45mm kranlås HARD6 Saksepinne (hårnål) til bolt 760002 Hurtiglås 4 5 760005 760006 760007 8100 Pos5 Hurtiglås underdel 8110 Pos4 Hurtiglås overdel 8111 Nøkkel for hurtiglås 6.48
- bare bedre løsninger KANTPROFILER 762008 612551 Kantprofil 4mm/28mm 2,5m Zinkprimet H=130mm Zink 762026 Kantprofil 4mm/28mm 2,5m rå. Lik 762008 762006 612521 Kantprofil 4mm/28mm 3m Zinkprimet H=150mm 762025 Kantprofil 4mm/28mm 3m rå H=150mm 762001 Kantprofil 4mm/28mm 7m rå H=150mm 762002 61253 Kantprofil 3mm/24mm 3m rå H=150mm 762004 6128 Kantprofil 3mm/28mm 6,8m rå H=150mm 6.49
KANTPROFILER 762005 61254 Kantprofil 4mm/42mm 3m Zinkprimet H=147mm 762018 Kantprofil 4 mm/42 mm 7 m rå H=147 mm 38 114 30 83 24 3 798103 Kantprofil 3mm/24mm 2,55m Zinkprimet H=170mm 170 25 352003 B1042 Kantprofil aluminium 6mm/42mm H=154mm 358015 A2234 Kantprofil aluminium 4mm/30mm H=120mm 6.50
Body Length(BL) L=BL/2-OH r 962 967 213 890 155 136 117 98 1140 972 EDBRO TIPPSYLINDER 79 SECTION - 898014 CS130043841B19A11 Tippsylinder CS130043841B19A11 1140 1175 9 Cylinder 4 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING 406 279 0 60 -.10 1" BSP INLET PORT 0 60 -.10 190 320 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 15 MAX 190 60 +40 345 0 MOUNTING CENTRES* 1287** 30 MAX 176 *Include 9mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS130043841B19A11 SPECIFICATION RATED CAPACITY : 23-42 TONNES*** Stage Diameter Length Stroke Swept Volume - - - - - OUTER COVER 213 890 - - 0 155 1175 - - 1 136 1140 938 14 2 117 1140 962 10 3 98 1140 967 7 4 79 1140 972 5 Final stroke reduced by 0 Total (+5/-10) 3839 36 Cylinder Mass (Kg) 157.07 Priming Volume 10.2 Rated Pressure (Bar) 150 Total Volume (Litres) 46.2 Maximum Pressure (Bar) 175 Max. first stage thrust 170 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 178 ; r = 750 BODY LENGTH (BL) W θ 4750 25 48 31 51 42 55 24 28 36 5000 45 48 52 23 26 32 5250 43 46 49 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 22 December 2009 16:47:09 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated 6.51
EDBRO TIPPSYLINDER 898015 CS130044241B19A11 Tippsylinder CS130044241B19A11 Body Length(BL) L=BL/2-OH r 406 279 0 60-0.10 W OH d = 178; r = 750; Working Pressure 175 bar 190 15 MAX 30 MAX 190 320 1" BSP INLET PORT Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 60-0 0.10 60 **1342 *345 +40 0 MOUNTING CENTRES 176 R106 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 155 213 136 98 79 SECTION SCALE 1 : 1 117 955 1240 1240 1240 1240 1275 Cylinder 4 stage front end with outer cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING *Includes 14mm Pull Out. Edbro plc Nelson Street, Bolton, England, BL3 2JJ Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS130044241B19A11 SPECIFICATION TIPPING CAPACITY : 26-42 TONNES*** Stage Diameter Length Stroke Swept Volume - - - - - OUTER COVER 213 955 - - 0 155 1275 - - 1 136 1240 1033 15 2 117 1240 1062 11 3 98 1240 1067 8 4 79 1240 1072 5 Total (+5/-10) 4234 39 Final stroke reduced by 0 Priming Volume 11 Cylinder Mass (Kg) 160 Total Volume (Litres) 50 Maximum Pressure (Bar) 190 Max. first stage thrust 170 KN ***TIPPING CAPACITY AT WORKING PRESSURE d BODY LENGTH (BL) 5250 5500 5750 28 34 42 48 51 54 27 31 38 45 48 51 26 29 35 43 46 49 150 450 750 Tipping angle ( ) Body + payload mass,w (tonne) For guidance only; Higher working pressures and tipping capacities may be possible. To check your application email - applications@edbro.co.uk NOTES OH 1. 2. 3. This cylinder is for lifting purposes only and side load conditions should be avoided Cylinder is painted in primer paint to RAL5013 Refer to www.edbro.com for;- Bracket details Installation instructions that must be observed Correct oil selection An explanation of tipping capacity Technical Specifications are subject to change without notice Date Created/Updated: 18 September 2014 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated 6.52
190 EDBRO TIPPSYLINDER 213 155 136 117 98 79 SECTION - - bare bedre løsninger 898016 CS130044641B19A11 Tippsylinder CS130044641B19A11 1340 Body Length(BL) L=BL/2-OH r 406 279 0 60 -.10 1" BSP INLET PORT 0 60 -.10 190 320 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 60 +40 345 0 MOUNTING CENTRES* 1437** 1340 1040 1375 9 Cylinder 4 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING 15 MAX 30 MAX 190 176 R106 *Include 9mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS130044641B19A11 SPECIFICATION RATED CAPACITY : 25-38 TONNES*** Stage Diameter Length Stroke Swept Volume - - - - - OUTER COVER 213 1040 - - 0 155 1375 - - 1 136 1340 1138 17 2 117 1340 1162 12 3 98 1340 1167 9 4 79 1340 1172 6 Final stroke reduced by 0 Total (+5/-10) 4639 44 Cylinder Mass (Kg) 167.87 Priming Volume 11.6 Rated Pressure (Bar) 175 Total Volume (Litres) 55.6 Maximum Pressure (Bar) 175 Max. first stage thrust 170 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 178 ; r = 750 BODY LENGTH (BL) W θ 5750 27 48 32 50 38 54 26 30 35 6000 46 48 51 25 28 33 6250 44 46 49 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 23 December 2009 12:47:49 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated 30 MAX 60 R106 6.53
EDBRO TIPPSYLINDER - bare bedre løsninger 898017 CS130045241B19A11 Tippsylinder CS130045241B19A11 Body Length(BL) L=BL/2-OH r 406 279 0 60 -.10 1" BSP INLET PORT 0 213 60 -.10 190 320 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 6.54 0 MAX 06 155 136 117 98 79 SECTION - 1490 1525 60 9 190 +40 345 0 MOUNTING CENTRES* 1587** 1490 1190 Cylinder 4 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING 15 MAX 30 MAX 176 R106 *Include 9mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS130045241B19A11 SPECIFICATION RATED CAPACITY : 24-37 TONNES*** Stage Diameter Length Stroke Swept Volume - - - - - OUTER COVER 213 1190 - - 0 155 1525 - - 1 136 1490 1288 19 2 117 1490 1312 14 3 98 1490 1317 10 4 79 1490 1322 6 Final stroke reduced by 0 Total (+5/-10) 5239 49 Cylinder Mass (Kg) 175.8 Priming Volume 13.1 Rated Pressure (Bar) 175 Total Volume (Litres) 62.1 Maximum Pressure (Bar) 175 Max. first stage thrust 170 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 178 ; r = 750 BODY LENGTH (BL) W θ 6250 27 50 31 52 37 55 26 28 32 6750 46 48 50 24 26 29 7250 42 44 46 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 23 December 2009 12:25:05 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated
190 213 - bare bedre løsninger EDBRO TIPPSYLINDER 898018 CS130045841B19A11 Tippsylinder CS130045841B19A11 Body Length(BL) L=BL/2-OH r 406 279 0 60 -.10 1" BSP INLET PORT 0 60 -.10 190 320 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 155 136 6.55 30 MAX 60 9 1640 1640 1340 1472 1467 1438 1462 117 98 79 1640 1675 R106 Cylinder 4 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING 15 MAX 60 +40 345 0 MOUNTING CENTRES* 1737** 30 MAX 190 176 R106 *Include 9mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS130045841B19A11 SPECIFICATION RATED CAPACITY : 24-33 TONNES*** Stage Diameter Length Stroke Swept Volume - - - - - OUTER COVER 213 1340 - - 0 155 1675 - - 1 136 117 1438 21 2 117 117 1462 16 3 98 117 1467 11 4 79 117 1472 7 Final stroke reduced by 0 Total (+5/-10) 5839 55 Cylinder Mass (Kg) 283.67 Priming Volume 14.5 Rated Pressure (Bar) 175 Total Volume (Litres) 69.5 Maximum Pressure (Bar) 175 Max. first stage thrust 170 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 178 ; r = 750 BODY LENGTH (BL) W θ 7000 26 49 29 52 33 54 25 27 30 7500 46 48 50 24 26 28 8000 43 45 47 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 23 December 2009 07:36:25 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated
EDBRO TIPPSYLINDER 940 1275 - bare bedre løsninger 898019 CS150044206B19A11 Tippsylinder CS150044206B19A11 Body Length(BL) L=BL/2-OH r 445 318 0 60 -.10 1" BSP INLET PORT 0 60 -.10 197 235 368 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 15 MAX. 80 345 +40 0 MOUNTING CENTRES* 190 1320** 30 MAX. R127 239 177 155 136 117 98 SECTION 1240 1240 1240 11 1240 Cylinder 4 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING *Include 11mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS150044206B19A11 SPECIFICATION RATED CAPACITY : 34-55 TONNES*** Stage Diameter Length Stroke Swept Volume - - - - - OUTER COVER 239 940 - - 0 177 1275 - - 1 155 1240 1025 19 2 136 1240 1047 15 3 117 1240 1062 11 4 98 1240 1067 8 Final stroke reduced by 0 Total (+5/-10) 4201 53 Cylinder Mass (Kg) 208.26 Priming Volume 13.8 Rated Pressure (Bar) 150 Total Volume (Litres) 66.8 Maximum Pressure (Bar) 175 Max. first stage thrust 230 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 229 ; r = 750 BODY LENGTH (BL) W θ 5250 37 47 44 50 55 53 35 41 49 5500 45 47 50 34 38 45 5750 42 45 48 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 19 November 2009 11:43:39 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated 6.56
1040 EDBRO TIPPSYLINDER 1375 - bare bedre løsninger 898020 CS150044606B19A11 Tippsylinder CS150044606B19A11 Body Length(BL) L=BL/2-OH r 445 318 0 60 -.10 1" BSP INLET PORT 0 60 -.10 197 235 368 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 15 MAX. 80 345 +40 0 MOUNTING CENTRES* 190 1420** 30 MAX. R127 239 177 155 136 117 98 SECTION 1340 1340 1340 11 1340 Cylinder 4 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING *Include 11mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS150044606B19A11 SPECIFICATION RATED CAPACITY : 37-55 TONNES*** Stage Diameter Length Stroke Swept Volume - - - - - OUTER COVER 239 1040 - - 0 177 1375 - - 1 155 1340 1125 21 2 136 1340 1147 17 3 117 1340 1162 12 4 98 1340 1167 9 Final stroke reduced by 0 Total (+5/-10) 4601 59 Cylinder Mass (Kg) 219.87 Priming Volume 15.0 Rated Pressure (Bar) 165 Total Volume (Litres) 74 Maximum Pressure (Bar) 175 Max. first stage thrust 230 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 229 ; r = 750 BODY LENGTH (BL) W θ 5750 39 47 45 50 55 53 38 43 50 6000 45 47 50 37 41 47 6250 43 45 48 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 19 November 2009 14:35:08 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated 6.57
EDBRO TIPPSYLINDER 898021 CS150045206B19A11 Tippsylinder CS150045206B19A11 Body Length(BL) L=BL/2-OH r 445 318 0 60-0.10 1" BSP INLET PORT Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 60-0 0.10 235 374 W OH d = 178; r = 750; Working Pressure165 bar 80 *342 +40 0 MOUNTING CENTRES 190 **1570 1490 1490 1490 1490 1190 Cylinder 4 stage front end with outer cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING 30 MAX 15 MAX 196 R127 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 *Includes 11mm Pull Out. Edbro plc Nelson Street, Bolton, England, BL3 2JJ Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS150045206B19A11 SPECIFICATION TIPPING CAPACITY : 35-53 TONNES*** Stage Diameter Length Stroke Swept Volume - - - - - OUTER COVER 239 1190 - - 0 177 1525 - - 1 155 1490 1275 24 2 136 1490 1297 19 3 117 1490 1312 14 4 98 1490 1317 10 Total (+5/-10) 5201 67 Final stroke reduced by 0 Priming Volume 17 Cylinder Mass (Kg) 232 Total Volume (Litres) 84 Maximum Pressure (Bar) 190 Max. first stage thrust 230 KN ***TIPPING CAPACITY AT WORKING PRESSURE d BODY LENGTH (BL) 6250 6750 7250 40 45 53 49 51 54 37 41 46 45 47 50 35 38 42 42 44 46 150 450 750 Tipping angle ( ) Body + payload mass,w (tonne) For guidance only; Higher working pressures and tipping capacities may be possible. To check your application email - applications@edbro.co.uk NOTES OH 1. 2. 3. This cylinder is for lifting purposes only and side load conditions should be avoided Cylinder is painted in primer paint to RAL5013 Refer to www.edbro.com for;- Bracket details Installation instructions that must be observed Correct oil selection An explanation of tipping capacity Technical Specifications are subject to change without notice Date Created/Updated: 18 September 2014 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated 6.58
1240 1240 - bare bedre løsninger 1240 EDBRO TIPPSYLINDER 898022 CS170055233B19A11 Tippsylinder CS170055233B19A11 Body Length(BL) L=BL/2-OH r 462 330 0 60 -.10 1.25" BSP INLET PORT 0 60 -.10 260 395 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 15 MAX 80 190 345 +40 0 MOUNTING CENTRES* 1326** 1275 945 10 1240 1240 Cylinder 5 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING 30 MAX 217 R135 *Includes 12mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS170055233B19A11 SPECIFICATION RATED CAPACITY : 38-60 TONNES*** Stage Diameter Length Stroke Swept Volume OUTER COVER 261 945 - - 0 199 1275 - - 1 176 1240 1014 25 2 155 1240 1037 20 3 136 1240 1047 15 4 117 1240 1062 11 5 98 1240 1067 8 Final stroke reduced by 0 Total (+5/-10) 5227 79 Cylinder Mass (Kg) 265.78 Priming Volume 12 Rated Pressure (Bar) 175 Total Volume (Litres) 91 Maximum Pressure (Bar) 175 Max. first stage thrust 260 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 229 ; r = 900 BODY LENGTH (BL) W θ 6500 44 47 51 50 60 52 41 46 52 7000 44 46 48 38 42 47 7500 41 42 44 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 01 September 2009 10:34:07 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated S 6.59
1340 1340 - bare bedre løsninger 1340 EDBRO TIPPSYLINDER 1340 898023 CS170055733B19A11 Tippsylinder CS170055733B19A11 Body Length(BL) L=BL/2-OH r 462 330 60 -.10 0 60 -.10 0 1.25" BSP INLET PORT 260 395 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 15 MAX 80 345 +40 0 MOUNTING CENTRES* 190 1426** 1375 1045 1340 Cylinder 5 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING 30 MAX 217 R135 *Includes 12mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS170055733B19A11 SPECIFICATION RATED CAPACITY : 38-57 TONNES*** Stage Diameter Length Stroke Swept Volume OUTER COVER 261 1045 - - 0 199 1375 - - 1 176 1340 1114 27 2 155 1340 1137 21 3 136 1340 1147 17 4 117 1340 1162 12 5 98 1340 1167 9 Final stroke reduced by 0 Total (+5/-10) 5727 86 Cylinder Mass (Kg) 281.27 Priming Volume 18 Rated Pressure (Bar) 175 Total Volume (Litres) 104 Maximum Pressure (Bar) 175 Max. first stage thrust 260 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 229 ; r = 900 BODY LENGTH (BL) W θ 7000 44 48 49 50 57 53 41 45 51 7500 45 47 49 38 42 46 8000 42 43 45 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 21 August 2009 15:30:09 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated S 6.60
1440 1440 - bare bedre løsninger 1440 EDBRO TIPPSYLINDER 1440 898024 CS170056233B19A11 Tippsylinder CS170056233B19A11 Body Length(BL) L=BL/2-OH r 462 330 0 60 -.10 0 60 -.10 1.25" BSP INLET PORT 260 395 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 15 MAX 80 345 +40 0 MOUNTING CENTRES* 190 1526** 1475 1145 1440 Cylinder 5 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING 30 MAX 217 R135 *Includes 12mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS170056233B19A11 SPECIFICATION RATED CAPACITY : 38-55 TONNES*** Stage Diameter Length Stroke Swept Volume OUTER COVER 261 1145 - - 0 199 1475 - - 1 176 1440 1214 30 2 155 1440 1237 23 3 136 1440 1247 18 4 117 1440 1262 14 5 98 1440 1267 10 Final stroke reduced by 0 Total (+5/-10) 6227 95 Cylinder Mass (Kg) 296.75 Priming Volume 19 Rated Pressure (Bar) 175 Total Volume (Litres) 114 Maximum Pressure (Bar) 175 Max. first stage thrust 260 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 229 ; r = 900 BODY LENGTH (BL) W θ 7500 43 49 48 51 55 53 40 44 49 8000 46 47 50 38 41 45 8500 43 44 46 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 21 August 2009 15:44:27 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated S 6.61
1540 1540 - bare bedre løsninger 1540 EDBRO TIPPSYLINDER 1540 898025 CS170056733B19A11 Tippsylinder CS170056733B19A11 Body Length(BL) L=BL/2-OH r 462 330 1.25" BSP INLET PORT 0 60 -.10 260 395 Customer to fit 2 x 1/8" BSP nipples for greasing. NG5 or NG6 OH 15 MAX 80 345 +40 0 MOUNTING CENTRES* 190 1626** 1575 1245 1540 Cylinder 5 stage front end with Outer Cover **ALLOW 50mm TO REMOVE CAP FOR SERVICING 30 MAX 217 R135 *Includes 12mm Pull Out Edbro plc Nelson Street, Bolton, Lancashire BL3 2JJ UK Tel +44 (0) 1204 528888 Fax +44 (0) 1204 531957 Email: postmaster@edbro.com Web: www.edbro.com CS170056733B19A11 SPECIFICATION RATED CAPACITY : 37-51 TONNES*** Stage Diameter Length Stroke Swept Volume OUTER COVER 261 1245 - - 0 199 1575 - - 1 176 1540 1314 32 2 155 1540 1337 25 3 136 1540 1347 20 4 117 1540 1362 15 5 98 1540 1367 10 Final stroke reduced by 0 Total (+5/-10) 6727 102 Cylinder Mass (Kg) 312.23 Priming Volume 21 Rated Pressure (Bar) 175 Total Volume (Litres) 123 Maximum Pressure (Bar) 175 Max. first stage thrust 260 KN ***TIPPING CAPACITY AT RATED PRESSURE d = 229 ; r = 900 BODY LENGTH (BL) W θ 8250 41 48 45 50 51 52 39 42 46 8750 45 47 49 37 40 43 9250 42 44 46 150 450 750 Tipping angle (θ) Body + payload mass,w (tonne) For guidance only; Higher Rated Pressures may be possible. To check your application, email Edbro plc at <applications@edbro.co.uk> NOTES - If hydraulic pressure is used to limit overloading, the system relief valve must be set to the Rated Pressure unless agreed otherwise by Edbro - The system relief valve can be set to Maximum Pressure if the load is limited by other means.see RATINGS page for advice - This cylinder is for lifting purposes only and sideload conditions must be avoided - Cylinder is painted in primer paint to RAL5013 - See bracket options page BRKT01, BRKT02 - See installation instructions INSTALL01 - Use oil according to specification OIL01 OH Technical Specifications are subject to change without notice Date Created/Updated: 21 August 2009 15:58:29 Refer www.edbro.com to confirm latest specification All dimensions are in 'mm', unless otherwise stated S 6.62