Dual redundant outputs IP67 sealed lever heights: 8mm and 60mm 5 lever colors Series 87 is offering paddle joysticks of high precision and quality - claims that are not only supported by sculpted grips with soft touch, but also by technical properties. Contactless Hall technology paired with a smooth and easy to operate mechanic are resulting in a long-lasting and reliably working joystick, specially suited for mild to extreme environments in mobile remote controls, cleaning machines, material handling and agricultural vehicles. Two different device geometries allow to choose the one optimally suiting the application needs. Technical Data Sensor Supply Voltage Vsupply Output Voltages Center Voltage Hall effect Current Consumption < 0mA Switch Output Loads Mechanical Operating Angle Max. load to mechanism Life Cycles Operating Temperature Storage Temperature Seal above Panel Damp Heat Salt Spray 5VDC ±0,5V transient free 0..5 V / 0,5..,5 V (Dual Output), PWM optional Vsupply/ ± 5% * full scale Open Drain, internal Pull-Up,5kΩ to Vsupply, smoothed to 0V with 00nF Minimum 0 kω, >00kΩ recommended 60 (±0 from center) Horizontal: 75N / Vertical: IK08 (BSEN66:00) 0 million cycles -5 C..+70 C -0 C..+85 C Conducted Emissions CISPR 5:008 Ed..0 Radiated Emissions IP67 above panel (with gasket) - BS EN 6059:99+A:0 BS EN 60068--78:00, days @ +85 C 85%RH BS EN 60068--:999, 8 hours @ +5 C with 5% NaCl CISPR 5:008 Ed..0, EN6000-6-:0 Radiated Immunity ISO 5-: 00 (50V/m), EN6000-6-: 005 Conducted Immunity ISO 5-:0 Signal Cable Transients EN 600-6-:005 AC Magnetic Field Immunity ESD Vibration Bump Freefall drop Shock MIL-STD-6F ISO 0605: 008 inc A: 0 (8kV contact / 5kV air discharge) EN6000-- ISO500 level in axes 0...50Hz, Level, 8 hours/axis BS EN 60068--7:009 0g 6ms half sine, 50 shocks in each sense of each axis, total 00 shocks BS EN 60068--:008, 000mm onto all faces and edges BS EN 60068--7:009 50g 6ms half sine, shocks in each sense of each axis, total 8 shocks Page: von 5
Order Code Series 87 Paddle 60mm height above panel 8mm height above panel Lever Operation Spring Return to Center = 0 Paddle Inserts Black Red Blue Yellow Green Output Options Dual Output, signals parallel (standard) Dual Output, signal inverted PWM Signal Output Signal 0.. 5,0V (rail to rail) 0,5..,5V Switching Points No Switches Switching at ±5 Switching at ±5 Switching at ±0 A B C D E 5 0 Wiring PIN Function Vsupply A Switch (+) Ground A Output A 5 Output B 6 Ground B 7 Switch (-) 8 Vsupply B (-) direction: Decreasing Signal Output (+) direction: Increasing Signal Output Pin Connection via 8-pole connector,,5 pitch. Cable not included. Please contact us for individual cable configurations. Page: von 5
Information on Output Options and Switching Points The 87 series joystick is configured as two electrical controls in one mechanical package. The Paddle operates from 5V and provides two proportional outputs. The second output is accurate to the first within +/-% of the power supply. The power supply for the secondary output is also completely independent. Customers may choose their preference of voltage outputs. The secondary output can be of the same or inverse polarity to the primary wiper. For example, with a secondary inverse output, the first and second outputs can be summed and compared to zero to verify that the joystick is operating correctly. Paddles having two identical outputs of the same polarity may be used to drive two identical dual redundant circuits Selectable Switching Points The joystick incorporates two Hall effect switches. The angle of the lever at the switch trigger point can be selected when ordering. If no switches are specified then the output on pins and 7 will be unused. The outputs are configured as open drain type with a K5 pull up resistor to 5V. Equivalent circuit for switch output 5Ω 75Ω 6kΩ 5V k5 00nF switch output 0mA max. Output Impedance The voltage outputs at center and at each end of travel are specified across an infinite load, with no current flowing. The output impedance specified in the electrical specification should be taken into account when designing a system. Load resistance of less than 0K Ohms is not recommended (also ref. to Technical Data page ) Output Characteristics (here: 0,5 -,5V Output) Note: When option Dual Parallel Output is selected the polarity of Switch is inverted. ) DUAL INVERSE OUTPUTS Switches at ±5.5V Switches at ±0 Output.5V Output Switch Switch ON On.5 Switch Switch ON On Switch On ON.5 Switch On ON Output Output -5-0 -0 0 0 0 5 -.5.5-5 -0-0 0 0 0 5 ) DUAL PARALLEL OUTPUTS Switches at ±5.5V Switches at ±0 Output.5V Output Output Output Switch Switch Off OFF.5 Switch Switch On ON Switch Off OFF.5 Switch On ON -5-0 -0 0 0 0 5 -.5.5-5 -0-0 0 0 0 5 Page: von 5
Technical Drawing Paddle 60mm height above panel M 8.50 6 60 8 WAY CONNECTOR.5mm PITCH 50 5.79 Dimensions in mm Panel Cut-Out & Mounting Paddle The Joystick is fitted with M bushes in all six positions and may be mounted with two different hole patterns: - Two screws (shown in yellow) - Four screws (shown in silver). N 0.9. 6.0 0.8 0.05.0 0.8 7 S TOP VIEW Screws are not included. The appropriate length of the screws is dependent on panel thickness. Dimensions in [inches] mm Page: von 5
Technical Drawing Paddle 8mm height above panel 7 (0.66) M 7.90 (0.) (.) 0 (.0) 0 (.0) 8.0 (.90) 8 WAY CONNECTOR.5mm PITCH (0. INCH PITCH) (.65) 9.9 (0.6) 6 (.0) Dimensions in mm (inches) Panel Cut-Out & Mounting Paddle The Joystick is fitted with M bushes in all six positions and may be mounted with two different hole patterns: - Two screws (shown in yellow) - Four screws (shown in silver). N 0.67 7.0 0..0 0 0.05.0 0.8 7 S TOP VIEW Screws are not included. The appropriate length of the screws is dependent on panel thickness. Dimensions in [inches] mm Page: 5 von 5