Veterinär-Osteosynthese und Traumatologie. Veterinary Osteosynhesis and Traumatology. Index

Veterinär-Osteosynthese und Traumatologie Veterinary Osteosynhesis and Traumatology

Deutsch: Schrauben........................................................................... VET.3 Platten.............................................................................. VET.9 Sets................................................................................. VET.16 Gleitnägel............................................................................ VET.26 Kirschner Draht....................................................................... VET.33 Externe Fixateure..................................................................... VET.37 Draht, Draht-Instrumente............................................................... VET.42 Klammern............................................................................ VET.50 Bohrer / Gewindeschneider............................................................. VET.51 Biegewerkzeug....................................................................... VET.59 Knochenhaltezangen................................................................... VET.61 Knocheninstrumente................................................................... VET.66 Bohrmaschinen....................................................................... VET.86 Akku-Bohrmaschine................................................................... VET.88 Container............................................................................ VET.103 Gipssäge............................................................................. VET.121 Englisch: Screws.............................................................................. VET.3 Plates............................................................................... VET.9 Kits................................................................................. VET.16 Gliding Nails.......................................................................... VET.26 Kirschner Wires....................................................................... VET.33 External Fixateur...................................................................... VET.37 Wire, Wire-Instruments................................................................. VET.42 Staples.............................................................................. VET.50 Drill Bits / Tapes...................................................................... VET.51 Bending Instruments................................................................... VET.59 Bone Holding Forceps.................................................................. VET.61 Bone Instruments..................................................................... VET.66 Drills................................................................................ VET.86 Battery-driven drill.................................................................... VET.88 Container............................................................................ VET.103 Plaster Saw.......................................................................... VET.121

Rev.: 101003 VET.2

Bone Screws Mini Screws 3,0 mm 1,5 mm 4,0 mm 1,5 mm 5,0 mm 2,5 mm Dia of thread Dia of core Dia of head Length 1.5 mm 2.0 mm 1.0 mm 3.0 mm 1.3 mm 4.0 mm 2.7 mm 1.9 mm 5.0 mm 6 mm 4-400 4-430 4-460 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 14 mm 16 mm 18 mm 20 mm 22 mm 24 mm 26 mm 28 mm 30 mm 32 mm 34 mm 36 mm 38 mm 40 mm 4-402 4-404 4-406 4-408 4-410 4-412 4-414 4-416 4-418 4-420 4-432 4-434 4-436 4-438 4-440 4-442 4-444 4-446 4-448 4-462 4-464 4-466 4-468 4-470 4-472 4-474 4-476 4-478 4-480 4-482 4-484 4-486 4-488 4-490 4-492 4-494 VET.3

Bone Screws Mini Screws Cruciate Head 5,0 mm 2,5 mm self cutting screws, tapping not needed Dia of thread Dia of core Dia of head Length 1.5 mm 2.0 mm 1.0 mm 3.0 mm 1.3 mm 4.0 mm 2.7 mm 1.9 mm 5.0 mm 6 mm 4-4001 4-4301 4-461 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 14 mm 16 mm 18 mm 20 mm 22 mm 24 mm 26 mm 28 mm 30 mm 32 mm 34 mm 36 mm 38 mm 40 mm 4-4003 4-4005 4-4007 4-4009 4-4011 4-4013 4-4015 4-4017 4-4019 4-4021 4-4303 4-4305 4-4307 4-4309 4-4311 4-4313 4-4315 4-4317 4-4319 4-463 4-465 4-467 4-469 4-471 4-473 4-475 4-477 4-479 4-481 4-483 4-485 4-487 4-489 4-491 4-493 4-495 VET.4

Bone Screws Small Screws with Spherical Head and Small Hexagonal Socket width across flats 2.5 mm 6,0 mm 6,0 mm 6,0 mm 2,5 mm 2,5 mm 2,5 mm 6,0 mm 2,5 mm Dia of thread 3.5 mm 3.5 mm 4.0 mm 4.0 mm Pitch 1.25 mm 1.75 mm 1.75 mm 1.75 mm Dia of core Dia of shaft Dia of head 2.4 mm 6.0 mm 1.9 mm 6.0 mm 1.9 mm 2.3 mm 6.0 mm 1.9 mm 6.0 mm Length 10 mm 12 mm 14 mm 16 mm 18 mm 20 mm 22 mm 24 mm 26 mm 28 mm 30 mm 32 mm 34 mm 35 mm 36 mm 38 mm 40 mm 42 mm 45 mm 48 mm 50 mm 55 mm 60 mm 65 mm 70 mm 75 mm 4-042 80 mm 4-044 4-002 4-050 4-100 4-140 4-004 4-052 4-102 4-142 4-006 4-054 4-104 4-144 4-008 4-056 4-106 4-146 4-010 4-058 4-108 4-148 4-012 4-060 4-110 4-150 4-014 4-062 4-112 4-152 4-016 4-064 4-114 4-154 4-018 4-066 4-116 4-156 4-020 4-068 4-118 4-158 4-022 4-070 4-120 4-160 4-024 4-072 4-121 4-162 4-025 4-073 4-122 4-164 4-026 4-074 4-027 4-075 4-028 4-076 4-124 4-166 4-029 4-030 4-078 4-126 4-168 4-031 4-032 4-080 4-128 4-170 4-034 4-082 4-129 4-172 4-036 4-084 4-130 4-174 4-038 4-040 4-176 Washer for Navicular Spongiosa Screws ø 7 mm VET.5

Bone Screws, self tapping 6,0 mm 6,0 mm 2,5 mm 2,5 mm 6,0 mm 2,5 mm self cutting screws, tapping not needed Dia of thread 3.5 mm 4.0 mm 4.0 mm Pitch 1.25 mm 1.75 mm 1.75 mm Dia of core Dia of shaft Dia of head 2.4 mm 6.0 mm 1.9 mm 2.3 mm 6.0 mm 1.9 mm 6.0 mm Length 10 mm 12 mm 14 mm 16 mm 18 mm 20 mm 22 mm 24 mm 26 mm 28 mm 30 mm 32 mm 34 mm 35 mm 36 mm 38 mm 40 mm 42 mm 45 mm 48 mm 50 mm 55 mm 60 mm 4-1002 4-1100 4-1140 4-1004 4-1102 4-1142 4-1006 4-1104 4-1144 4-1008 4-1106 4-1146 4-1010 4-1108 4-1148 4-1012 4-1110 4-1150 4-1014 4-1112 4-1152 4-1016 4-1114 4-1154 4-1018 4-1116 4-1156 4-1020 4-1118 4-1158 4-1022 4-1120 4-1160 4-1024 4-1121 4-1162 4-1025 4-1122 4-1164 4-1026 4-1027 4-1028 4-1124 4-1166 4-1029 4-1030 4-1126 4-1168 4-1031 4-1032 4-1128 4-1170 4-1172 4-1174 VET.6

Bone Screws Large Screws with large hexagonal flats 3.5 mm 8,0 mm 3,5 mm Washers 3-520 11 mm 3-522 13 mm SW 8 mm 3-524 Nut for 4.5 mm Cortex Screws Dia of thread 4.5 mm 4.5 mm 4.5 mm 6.5 mm 6.5 mm 6.5 mm Dia of core Dia of shaft Dia of head 3.0 mm 8.0 mm 3.1 mm 4.5 mm 8.0 mm 3.0 mm 3.0 mm 8.0 mm 3.0 mm 4.5 mm 8.0 mm 3.0 mm 4.5 mm 8.0 mm 3.0 mm 8.0 mm Length 14 mm 16 mm 18 mm 20 mm 22 mm 24 mm 25 mm 26 mm 28 mm 30 mm 32 mm 34 mm 35 mm 36 mm 38 mm 40 mm 42 mm 44 mm 45 mm 46 mm 48 mm 50 mm 52 mm 54 mm 55 mm 56 mm 58 mm 60 mm 65 mm 70 mm 75 mm 80 mm 85 mm 90 mm 95 mm 100 mm 105 mm 110 mm 115 mm 120 mm 3-200 3-202 3-204 3-206 3-208 3-210 3-212 3-214 3-216 3-218 3-220 3-222 3-224 3-226 3-228 3-230 3-232 3-234 3-236 3-238 3-240 3-242 3-244 3-246 3-248 3-250 3-254 3-260 3-262 3-264 3-266 3-268 3-269 3-270 3-271 3-272 3-280 3-282 3-284 3-286 3-288 3-290 3-292 3-294 3-296 3-298 3-300 3-302 3-304 3-306 3-308 3-310 3-312 3-314 3-316 3-318 3-320 3-322 3-324 3-326 3-328 3-330 3-332 3-334 3-336 3-338 3-350 3-352 3-354 3-356 3-358 3-360 3-362 3-364 3-366 3-368 3-370 3-371 3-372 3-382 3-384 3-386 3-388 3-390 3-392 3-394 3-396 3-398 3-400 3-402 3-404 3-406 3-408 3-410 3-412 3-414 3-415 3-416 3-434 3-436 3-438 3-440 3-442 3-444 3-446 3-448 3-450 3-452 3-454 3-456 3-458 3-460 3-462 3-464 3-466 3-480 3-482 3-484 3-486 3-488 3-490 3-492 3-494 3-496 3-498 3-500 3-502 3-504 3-506 3-508 3-510 3-512 3-514 3-516 3-518 VET.7

Bone Screws, self tapping 8,0 mm 3,5 mm self cutting screws, tapping not needed Dia of thread 4.5 mm 4.5 mm Dia of core Dia of shaft Dia of head 3.0 mm 8.0 mm 4.5 mm 8.0 mm Length 14 mm 16 mm 18 mm 20 mm 22 mm 24 mm 25 mm 26 mm 28 mm 30 mm 32 mm 34 mm 35 mm 36 mm 38 mm 40 mm 42 mm 44 mm 45 mm 46 mm 48 mm 50 mm 52 mm 54 mm 55 mm 56 mm 58 mm 60 mm 65 mm 70 mm 75 mm 80 mm 85 mm 90 mm 95 mm 100 mm 105 mm 110 mm 3-1200 3-1202 3-1204 3-1206 3-1208 3-1210 3-1212 3-1214 3-1216 3-1218 3-1220 3-1222 3-1224 3-1226 3-1228 3-1230 3-1232 3-1234 3-1236 3-1238 3-1240 3-1242 3-1244 3-1246 3-1248 3-1250 3-1252 3-1254 3-1256 3-1258 3-1260 3-1262 3-1264 3-1266 3-1280 3-1282 3-1284 3-1286 3-1288 3-1290 3-1292 3-1294 3-1296 3-1298 3-1300 3-1302 3-1304 3-1306 3-1308 3-1310 3-1312 3-1314 3-1316 3-1318 3-1320 3-1322 3-1324 3-1326 3-1328 3-1330 3-1332 3-1334 3-1336 3-1338 VET.8

Mini Plates Plates for 2.0 mm ø Screws Length Holes 4-570 22 mm 4 4-572 27 mm 5 4-574 32 mm 6 4-576 37 mm 7 4-578 42 mm 8 Profil: Thick 4-6 holes 1.0 mm Thick 7-8 holes 1.5 mm Broad 5 mm Distance 5 mm Profil: Distance between holes: 5.0 x 1.2 mm 5.0 mm Mini T-Plates for 2.0 mm Screws Primary Indication: Fracture of the phalanges Number of holes Length in head in shaft 4-580 50 mm 3 9 4-582 50 mm 4 9 4-584 Straight Mini Plates for 2.0 mm screws with 20 holes, 100 mm length 4-586 Mini - Adaptationplate for 2.0 mm screws with 20 holes, 100 mm length Straight Mini Plates Length Holes 4-590 17 mm 3 4-592 23 mm 4 4-594 29 mm 5 4-596 35 mm 6 Profil: Thick: Broad: Distance: 1.2 mm 5 mm 6 mm 4-600 oblique left 4-602 oblique right 4-604 straight 4-606 angled 90 left 4-608 angled 90 right VET.9

Mini Plates Plates for 2.7 mm ø Screws Profil: Distance between holes: 8.0 x 2.0 mm 8.0 mm Finger Plates Quarter-tubular Plates Length Holes 4-520 20 mm 2 4-522 36 mm 4 4-524 44 mm 5 4-526 52 mm 6 Length Holes 4-540 25 mm 3 4-542 33 mm 4 4-544 41 mm 5 4-546 49 mm 6 4-548 57 mm 7 4-550 65 mm 8 Profil: Distance between holes: 8.0 x 2.5 mm 8.0 mm Length Holes 4-528 60 mm 7 4-530 68 mm 8 4-532 76 mm 9 4-534 84 mm 10 4-536 100 mm 12 4-552 oblique left 4-554 oblique right 4-556 straight 4-558 angled left 90 4-560 angled right 90 4-562 VET.10

24-080 Acetabulum Plates 6 Holes 31 mm for 1.5 mm Screws 24-082 Acetabulum Plates 4 Holes 31 mm for 2.7 mm and 3.5 mm Screws 24-084 Acetabulum Plates 6 Holes 31 mm for 2.7 mm and 3.5 mm Screws 24-100 Buttress Plates 4 Holes 35 mm for 2.0 mm Screws 24-102 Buttress Plates 5 Holes 36 mm for 2.0 mm Screws 24-104 Buttress Plates 6 Holes 52 mm for 2.0 mm Screws 24-110 24-112 24-114 T-Plates for 2.7 mm and 3.5 mm Screws 24-120 5 Holes 24-122 7 Holes 24-124 9 Holes VET.11

Carpal Arthrodesis Plates 24-150 Compression 2.0 mm / 2.7 mm 24-152 Compression 2.7 mm / 3.5 mm 24-154 Broad Compression 3.5 mm / 3.5 mm 3,5 mm Small Fragment Plates for 3.5 ø screws Profil 10 x 3 mm Distance between Holes 12 and 16 mm Length Holes 4-200 25 mm 2 4-202 37 mm 3 4-204 49 mm 4 4-206 61 mm 5 4-208 73 mm 6 4-210 85 mm 7 4-212 97 mm 8 4-214 109 mm 9 4-216 121 mm 10 4-218 145 mm 12 10 mm Small Fragment Plates with DC gliding holes for Corticalis Screws ø 3,5 mm and Cancellous ø 4,0 mm Length Holes 24-200 86 mm 7 24-202 98 mm 8 24-204 110 mm 9 24-206 122 mm 10 24-208 134 mm 11 24-210 146 mm 12 24-212 158 mm 13 24-214 170 mm 14 24-216 182 mm 16 24-218 194 mm 18 24-220 206 mm 20 24-222 218 mm 22 Miscellaneous Implants 24-160 Cut-to-Length Plates 2.0 m / 1.5 mm Dimensions: 1.0 mm x 7 mm x 300 mm, 50 round holes 24-162 Cut-to-Length Plates 2.7 m / 2.0 mm Dimensions: 1.5 mm x 7 mm x 300 mm, 50 round holes VET.12

Narrow Compression Plates Profile: 12 x 3.8 mm Distance between holes: 16 and 25 mm Length Holes 3-600 39 mm 2 3-602 55 mm 3 3-604 71 mm 4 3-606 87 mm 5 3-608 103 mm 6 3-610 119 mm 7 3-612 135 mm 8 3-614 151 mm 9 Length Holes 3-616 167 mm 10 3-618 183 mm 11 3-620 199 mm 12 3-622 215 mm 13 3-624 231 mm 14 3-626 247 mm 15 3-628 263 mm 16 Broad Compression Plates Profile: 16 x 4.8 mm Distance between holes: 16 and 25 mm Length Holes 3-640 103 mm 6 3-642 119 mm 7 3-644 135 mm 8 3-646 151 mm 9 3-648 167 mm 10 3-650 183 mm 11 3-652 199 mm 12 Length Holes 3-654 215 mm 13 3-656 231 mm 14 3-658 247 mm 15 3-660 263 mm 16 3-662 279 mm 17 3-664 295 mm 18 Semi-Tubular Plates Profile: 12 x 1 mm Distance between holes: 16 and 26 mm Length Holes 3-670 39 mm 2 3-672 55 mm 3 3-674 71 mm 4 3-676 87 mm 5 3-678 103 mm 6 Length Holes 3-680 119 mm 7 3-682 135 mm 8 3-684 151 mm 9 3-686 167 mm 10 3-688 183 mm 11 3-690 199 mm 12 VET.13

Straight Plates Broad Lengthening Plates with 8 holes Amount of lengthening Length 3-750 30 mm 135 mm 3-752 40 mm 145 mm 3-754 50 mm 155 mm 3-756 60 mm 165 mm Narrow Lengthening Plates with 8 holes Amount of lengthening Length 3-760 30 mm 135 mm 3-762 40 mm 145 mm 3-764 50 mm 155 mm 3-766 60 mm 165 mm 3-768 70 mm 175 mm 3-770 80 mm 185 mm Broad Lengthening Plates with 10 holes Amount of lengthening Length 3-772 50 mm 179 mm 3-774 60 mm 189 mm 3-776 70 mm 199 mm 3-778 80 mm 209 mm 3-779 90 mm 219 mm 3-780 100 mm 229 mm 3-782 110 mm 239 mm 3-784 120 mm 249 mm VET.14

Sets VET.15

MINI IMPLANTATE-SET MINI IMPLANTATE-KIT Implantate und Instrumente für Schrauben mit Gewinde ø 1,5 und 2,0 mm Implants and instruments for screws with thread 1,5 und 2,0 mm diam. V-2400 VET.16

MINI IMPLANTATE-SET MINI IMPLANTATE-KIT Implantate und Instrumente für Schrauben mit Gewinde ø 1,5 und 2,0 mm Implants and instruments for screws with thread 1,5 und 2,0 mm diam. V-2400 4-400 3 Cortical screws 1.5 mm diam. 6 mm long. 4-402 3 Cortical screws 1.5 mm diam. 7 mm long. 4-404 3 Cortical screws 1.5 mm diam. 8 mm long. 4-406 3 Cortical screws 1.5 mm diam. 9 mm long. 4-408 3 Cortical screws 1.5 mm diam. 10 mm long. 4-410 3 Cortical screws 1.5 mm diam. 11 mm long. 4-412 3 Cortical screws 1.5 mm diam. 12 mm long. 4-414 3 Cortical screws 1.5 mm diam. 14 mm long. 4-416 3 Cortical screws 1.5 mm diam. 16 mm long. 4-430 4 Cortical screws 2.0 mm diam. 6 mm long. 4-432 4 Cortical screws 2.0 mm diam. 8 mm long. 4-434 4 Cortical screws 2.0 mm diam. 10 mm long. 4-436 3 Cortical screws 2.0 mm diam. 12 mm long. 4-438 3 Cortical screws 2.0 mm diam. 14 mm long. 4-440 3 Cortical screws 2.0 mm diam. 16 mm long. 4-442 3 Cortical screws 2.0 mm diam. 18 mm long. 4-444 3 Cortical screws 2.0 mm diam. 20 mm long. 4-590 1 Mini bone plate, 3 holes 4-592 1 Mini bone plate, 4 holes 4-594 1 Mini bone plate, 5 holes 4-606 1 Mini L plate, left 4-608 1 Mini L plate, right 4-600 1 Mini L plate, oblique left 4-602 1 Mini L plate, oblique right 4-604 1 Mini T plate 4-570 1 Mini bone plate, 4 holes 4-572 1 Mini bone plate, 5 holes 4-574 1 Mini bone plate, 6 holes 4-576 1 Mini bone plate, 7 holes 4-578 1 Mini bone plate, 8 holes 9-010 2 Twist drills, 1.1 mm diam. AO 9-012 2 Twist drills, 1.5 mm diam. AO 9-071 2 Taps, 1.5 mm diam. with dental shaft 9-072 2 Taps, 2.0 mm diam. with dental shaft 9-096 1 Quick action chuck with dental shaft 9-110 1 Screw depth gauge for mini screws 9-170 1 Screw driver, width across flats 1.5 mm 4-184 1 Self holding screw forceps 7-200 10 KIRSCHNER wires, 70 mm, 0.8 mm diam. 9-410 2 Bending Pliers for small plates 9-250 1 Mini drill sleeve for drill 1.1 and 1.5 mm diam. 9-252 1 Mini drill sleeve for drill 2.0 diam. 9-630 1 Holding forceps for small bone plates 9-596 1 Reposition forceps for very small bones 19E-266.02 1 Small set container, gold, with perforation in lid and bottom. 300 x 140 x 70 mm 19E-353.04 1 Identification label, blue T 310 1 Rack for 1.5 mm diam. screws T 311 1 Rack for 2.0 mm diam. screws 15-2150 1 Upper storage wire base 19E-137.01 2 Wrapping drapes 4-400 3 Corticalis-Schrauben 1,5 mm ø 6 mm lang 4-402 3 Corticalis-Schrauben 1,5 mm ø 7 mm lang 4-404 3 Corticalis-Schrauben 1,5 mm ø 8 mm lang 4-406 3 Corticalis-Schrauben 1,5 mm ø 9 mm lang 4-408 3 Corticalis-Schrauben 1,5 mm ø 10 mm lang 4-410 3 Corticalis-Schrauben 1,5 mm ø 11 mm lang 4-412 3 Corticalis-Schrauben 1,5 mm ø 12 mm lang 4-414 3 Corticalis-Schrauben 1,5 mm ø 14 mm lang 4-416 3 Corticalis-Schrauben 1,5 mm ø 16 mm lang 4-430 4 Corticalis-Schrauben 2,0 mm ø 6 mm lang 4-432 4 Corticalis-Schrauben 2,0 mm ø 8 mm lang 4-434 4 Corticalis-Schrauben 2,0 mm ø 10 mm lang 4-436 3 Corticalis-Schrauben 2,0 mm ø 12 mm lang 4-438 3 Corticalis-Schrauben 2,0 mm ø 14 mm lang 4-440 3 Corticalis-Schrauben 2,0 mm ø 16 mm lang 4-442 3 Corticalis-Schrauben 2,0 mm ø 18 mm lang 4-444 3 Corticalis-Schrauben 2,0 mm ø 20 mm lang 4-590 1 Mini-Plättchen, 3 Loch 4-592 1 Mini-Plättchen, 4 Loch 4-594 1 Mini-Plättchen, 5 Loch 4-606 1 Mini-Plättchen, links 4-608 1 Mini-Plättchen, rechts 4-600 1 Mini-Plättchen, schräg links 4-602 1 Mini-Plättchen, schräg rechts 4-604 1 Mini-T-Plättchen 4-570 1 Mini-Plättchen, 4 Loch 4-572 1 Mini-Plättchen, 5 Loch 4-574 1 Mini-Plättchen, 6 Loch 4-576 1 Mini-Plättchen, 7 Loch 4-578 1 Mini-Plättchen, 8 Loch 9-010 2 Spiralbohrer, ø 1,1 mm AO 9-012 2 Spiralbohrer, ø 1,5 mm AO 9-071 2 Gewindeschneider, ø 1,5 mm, mit Dental Schaft 9-072 2 Gewindeschneider, ø 2,0 mm, mit Dental Schaft 9-096 1 Schnellspannfutter mit Dental-Schaft 9-110 1 Schraubenmeßgerät für Mini-Schrauben 9-170 1 Schraubenzieher, SW 1,5 mm 4-184 1 Selbsthaltende Schraubenpinzette 7-200 10 KIRSCHNER-Drähte, 70 mm, ø 0,8 mm 9-410 2 Plattenbiegezangen für kleine Plättchen 9-250 1 Mini-Bohrbüchse für Bohrer ø 1,1 und 1,5 mm 9-252 1 Mini-Bohrbüchse für Bohrer ø 2,0 mm 9-630 1 Plattenhaltezange 9-596 1 Repositionszange für sehr kleine Knochen 19E-266.02 1 Klein-Set-Container, gold, mit Deckel-und Bodenperforation, 300 x 140 x 70 mm 19E-353.04 1 Kennzeichnungschild, blau T 310 1 Rack für ø 1,5 mm Schrauben T 311 1 Rack für ø 2,0 mm Schrauben 15-2150 1 Oberer Lagerungseinsatz 19E-137.01 2 Ein- bzw. Umschlagtücher VET.17

BASIS-SET 1 STARTER-KIT 1 Implantate und Instrumente für Schrauben mit Gewinde ø 2,7 mm Implants and instruments for screws with thread 2.7 mm diam. V-2402 VET.18

BASIS-SET 1 STARTER-KIT 1 Implantate und Instrumente für Schrauben mit Gewinde ø 2,7 mm Implants and instruments for screws with thread 2.7 mm diam. V-2402 4-460 4 Cortical screws, 2.7 mm diam. 6 mm long. 4-462 5 Cortical screws, 2.7 mm diam. 8 mm long. 4-464 6 Cortical screws, 2.7 mm diam. 10 mm long. 4-466 7 Cortical screws, 2.7 mm diam. 12 mm long. 4-468 8 Cortical screws, 2.7 mm diam. 14 mm long. 4-470 8 Cortical screws, 2.7 mm diam. 16 mm long. 4-472 7 Cortical screws, 2.7 mm diam. 18 mm long. 4-474 6 Cortical screws, 2.7 mm diam. 20 mm long. 4-476 5 Cortical screws, 2.7 mm diam. 22 mm long. 4-478 4 Cortical screws, 2.7 mm diam. 24 mm long. 4-540 1 Small fragment plate, 3 holes 4-542 1 Small fragment plate, 4 holes 4-546 1 Small fragment plate, 6 holes 4-550 1 Small fragment plate, 8 holes 4-558 1 Small fragment L plate, left 4-560 1 Small fragment L plate, right 4-552 1 Small fragment L plate, oblique left 4-554 1 Small fragment L plate, oblique right 4-556 1 Small fragment T plate 4-562 1 Multiple fragment plate 4-520 1 Sherical gliding plate, 2 holes 4-522 1 Sherical gliding plate, 4 holes 4-524 1 Sherical gliding plate, 5 holes 4-526 1 Sherical gliding plate, 6 holes 4-528 1 Sherical gliding plate, 7 holes 4-530 1 Sherical gliding plate, 8 holes 4-176 3 Washer, 7 mm diam. 3-074 1 Bending template for small plates, 5 holes 3-075 1 Bending template for small plates, 7 holes 3-076 1 Bending template for small plates, 9 holes 4-184 1 Screw holding forceps 9-014 2 Twist drill, 2.0 mm diam. with AO shaft 9-018 2 Twist drill, 2.7 mm diam. with AO shaft 9-102 1 Countersink, with AO shaft 9-073 2 Taps, 2.7 mm diam. with A shaft 9-172 1 Screw driver, with across flats 2.5 mm diam. 9-173 1 Screw holding sheath 9-094 1 Handle with quick-action chuck 9-252 1 Drill guide and -sleeve for drills 2.0 mm diam. 9-254 1 Drill guide and -sleeve for drills 2.5 mm diam. 9-276 1 Insert sleeve for drills 2.0 mm diam. 9-278 1 Insert sleeve for drills 2.7 mm diam. 9-259 1 Small pointed drill guide 9-268 1 Drill guide, suitable for drills, 2.0 mm diam. 9-402 1 Bending iron for small plates 9-404 1 Bending iron for small plates 9-112 1 Screw depth gauge 9-116 1 Sharp hook 19E-266.03 1 Small set container, red, with perforation in lid and bottom, 300 x 140 x 70 mm 19E-353.04 1 Identification label, blue T 312 1 Rack for 2,7 mm diam. screws 15-1150 1 Upper storage wire base 19E-137.01 2 Wrapping drapes 4-460 4 Corticalis-Schrauben, ø 2,7 mm, 6 mm lang 4-462 5 Corticalis-Schrauben, ø 2,7 mm, 8 mm lang 4-464 6 Corticalis-Schrauben, ø 2,7 mm, 10 mm lang 4-466 7 Corticalis-Schrauben, ø 2,7 mm, 12 mm lang 4-468 8 Corticalis-Schrauben, ø 2,7 mm, 14 mm lang 4-470 8 Corticalis-Schrauben, ø 2,7 mm, 16 mm lang 4-472 7 Corticalis-Schrauben, ø 2,7 mm, 18 mm lang 4-474 6 Corticalis-Schrauben, ø 2,7 mm, 20 mm lang 4-476 5 Corticalis-Schrauben, ø 2,7 mm, 22 mm lang 4-478 4 Corticalis-Schrauben, ø 2,7 mm, 24 mm lang 4-540 1 Kleinfragment-Plättchen, 3-Loch 4-542 1 Kleinfragment-Plättchen, 4-Loch 4-546 1 Kleinfragment-Plättchen, 6-Loch 4-550 1 Kleinfragment-Plättchen, 8-Loch 4-558 1 Kleinfragment-L-Plättchen, links 4-560 1 Kleinfragment-L-Plättchen, rechts 4-552 1 Kleinfragment-L-Plättchen, schräg links 4-554 1 Kleinfragment-L-Plättchen, schräg rechts 4-556 1 Kleinfragment-T-Plättchen 4-562 1 Mehrfragment-Plättchen 4-520 1 Selbstspannende Knochenplatte, 2-Loch 4-522 1 Selbstspannende Knochenplatte, 4-Loch 4-524 1 Selbstspannende Knochenplatte, 5-Loch 4-526 1 Selbstspannende Knochenplatte, 6-Loch 4-528 1 Selbstspannende Knochenplatte, 7-Loch 4-530 1 Selbstspannende Knochenplatte, 8-Loch 4-176 3 Unterlegscheibe, ø 7 mm 3-074 1 Biegeschablone für kleine Platten, 5-Loch 3-075 1 Biegeschablone für kleine Platten, 7-Loch 3-076 1 Biegeschablone für kleine Platten, 9-Loch 4-184 1 Schraubenhaltepinzettte 9-014 2 Spiralbohrer, ø 2,0 mm mit AO Schaft 9-018 2 Spiralbohrer, ø 2,7 mm mit AO Schaft 9-102 1 Kopfraumfräser, mit AO Schaft 9-073 2 Gewindeschneider, ø 2,7 mm mit AO Schaft 9-172 1 Schraubenzieher, SW 2,5 mm 9-173 1 Schraubenhaltehülse 9-094 1 Handgriff mit Schnellspannfutter 9-252 1 Ziel- und Plattenbohrbüchse für ø 2,0 mm 9-254 1 Ziel- und Plattenbohrbüchse für ø 2,5 mm 9-276 1 Steckbohrbüchse für Bohrer ø 2,0 mm 9-278 1 Steckbohrbüchse für Bohrer ø 2,7 mm 9-259 1 Kleines Zielgerät mit Spitze 9-268 1 Spann- und Neutralbohrbüchse für Bohrer ø 2,0 mm 9-402 1 Biege- und Schränkhebel für kleine Platten 9-404 1 Biege- und Schränkhebel für kleine Platten 9-112 1 Schraubenmeßgerät 9-116 1 Scharfer Haken 19E-266.03 1 Klein-Set-Container, rot, mit Deckel- und Bodenperforation, 300 x 140 x 70 mm 19E-353.04 1 Kennzeichnungschild, blau T 312 1 Rack für ø 2,7 mm Schrauben 15-1150 1 Unterer Lagerungseinsatz 19E-137.01 2 Ein- bzw. Umschlagtücher VET.19

AUFBAU-SET 1 ADVANCED KIT 1 Implantate für Schrauben mit Gewinde ø 3,5 mm - 4,5 mm Implants for screws with thread 3,5-4,5 mm diam. V-2404 VET.20

AUFBAU-SET 1 ADVANCED KIT 1 Implantate für Schrauben mit Gewinde ø 3,5 mm - 4,5 mm Implants for screws with thread 3,5-4,5 mm diam. V-2404 4-002 3 Cortical screws, 3.5 mm diam. 10 mm long. 4-004 4 Cortical screws, 3.5 mm diam. 12 mm long. 4-006 5 Cortical screws, 3.5 mm diam. 14 mm long. 4-008 6 Cortical screws, 3.5 mm diam. 16 mm long. 4-010 7 Cortical screws, 3.5 mm diam. 18 mm long. 4-012 8 Cortical screws, 3.5 mm diam. 20 mm long. 4-014 8 Cortical screws, 3.5 mm diam. 22 mm long. 4-016 7 Cortical screws, 3.5 mm diam. 24 mm long. 4-018 6 Cortical screws, 3.5 mm diam. 26 mm long. 4-020 5 Cortical screws, 3.5 mm diam. 28 mm long. 4-022 4 Cortical screws, 3.5 mm diam. 30 mm long. 4-024 3 Cortical screws, 3.5 mm diam. 32 mm long. 4-100 2 Cancellous screws, 4.0 mm diam., 10 mm long 4-102 2 Cancellous screws, 4.0 mm diam., 12 mm long 4-104 2 Cancellous screws, 4.0 mm diam., 14 mm long 4-106 2 Cancellous screws, 4.0 mm diam., 16 mm long 4-108 2 Cancellous screws, 4.0 mm diam., 18 mm long 4-110 2 Cancellous screws, 4.0 mm diam., 20 mm long 4-112 2 Cancellous screws, 4.0 mm diam., 22 mm long 4-114 2 Cancellous screws, 4.0 mm diam., 24 mm long 4-116 2 Cancellous screws, 4.0 mm diam., 26 mm long 4-118 2 Cancellous screws, 4.0 mm diam., 28 mm long 4-120 2 Cancellous screws, 4.0 mm diam., 30 mm long 4-122 2 Cancellous screws, 4.0 mm diam., 35 mm long 4-124 2 Cancellous screws, 4.0 mm diam., 40 mm long 3-204 1 Cortical screw, 4.5 diam., 18 mm long. 3-206 2 Cortical screw, 4.5 diam., 20 mm long. 3-208 3 Cortical screw, 4.5 diam., 22 mm long. 3-210 4 Cortical screw, 4.5 diam., 24 mm long. 3-212 4 Cortical screw, 4.5 diam., 26 mm long. 3-214 4 Cortical screw, 4.5 diam., 28 mm long. 3-216 4 Cortical screw, 4.5 diam., 30 mm long. 3-218 4 Cortical screw, 4.5 diam., 32 mm long. 3-220 4 Cortical screw, 4.5 diam., 34 mm long. 3-222 3 Cortical screw, 4.5 diam., 36 mm long. 3-224 2 Cortical screw, 4.5 diam., 38 mm long. 3-226 1 Cortical screw, 4.5 diam., 40 mm long. 3-604 1 Sherical gliding plate, narrow, 4 holes 3-606 1 Sherical gliding plate, narrow, 5 holes 3-608 1 Sherical gliding plate, narrow, 6 holes 3-610 1 Sherical gliding plate, narrow, 7 holes 4-204 1 Sherical gliding plate, small, 4 holes 4-206 1 Sherical gliding plate, small, 5 holes 4-208 1 Sherical gliding plate, small, 6 holes 4-210 1 Sherical gliding plate, small, 7 holes 4-212 1 Sherical gliding plate, small, 8 holes 3-070 1 Bending template, 5 holes 3-071 1 Bending template, 7 holes 4-176 3 Washers, 7 mm diam. 3-520 3 Washers, 11 mm diam. 19E-267.05 1 Small set container, green with perforation in lid and bottom, 300 x 140 x 100 mm 19E-353.04 1 Identification label, blue 15-2150 1 Storage wire base 19E-137.01 1 Wrapping drapes T 313 1 Rack for 3.5 mm diam. screws T 316 1 Rack for 4.0 mm diam. screws T 317 1 Rack for 4.5 mm diam. screws 4-002 3 Corticalis-Schrauben, ø 3,5 mm, 10 mm lang 4-004 4 Corticalis-Schrauben, ø 3,5 mm, 12 mm lang 4-006 5 Corticalis-Schrauben, ø 3,5 mm, 14 mm lang 4-008 6 Corticalis-Schrauben, ø 3,5 mm, 16 mm lang 4-010 7 Corticalis-Schrauben, ø 3,5 mm, 18 mm lang 4-012 8 Corticalis-Schrauben, ø 3,5 mm, 20 mm lang 4-014 8 Corticalis-Schrauben, ø 3,5 mm, 22 mm lang 4-016 7 Corticalis-Schrauben, ø 3,5 mm, 24 mm lang 4-018 6 Corticalis-Schrauben, ø 3,5 mm, 26 mm lang 4-020 5 Corticalis-Schrauben, ø 3,5 mm, 28 mm lang 4-022 4 Corticalis-Schrauben, ø 3,5 mm, 30 mm lang 4-024 3 Corticalis-Schrauben, ø 3,5 mm, 32 mm lang 4-100 2 Spongiosa-Schrauben, ø 4,0 mm, 10 mm lang 4-102 2 Spongiosa-Schrauben, ø 4,0 mm, 12 mm lang 4-104 2 Spongiosa-Schrauben, ø 4,0 mm, 14 mm lang 4-106 2 Spongiosa-Schrauben, ø 4,0 mm, 16 mm lang 4-108 2 Spongiosa-Schrauben, ø 4,0 mm, 18 mm lang 4-110 2 Spongiosa-Schrauben, ø 4,0 mm, 20 mm lang 4-112 2 Spongiosa-Schrauben, ø 4,0 mm, 22 mm lang 4-114 2 Spongiosa-Schrauben, ø 4,0 mm, 24 mm lang 4-116 2 Spongiosa-Schrauben, ø 4,0 mm, 26 mm lang 4-118 2 Spongiosa-Schrauben, ø 4,0 mm, 28 mm lang 4-120 2 Spongiosa-Schrauben, ø 4,0 mm, 30 mm lang 4-122 2 Spongiosa-Schrauben, ø 4,0 mm, 35 mm lang 4-124 2 Spongiosa-Schrauben, ø 4,0 mm, 40 mm lang 3-204 1 Corticalis-Schrauben, ø 4,5 mm, 18 mm lang 3-206 2 Corticalis-Schrauben, ø 4,5 mm, 20 mm lang 3-208 3 Corticalis-Schrauben, ø 4,5 mm, 22 mm lang 3-210 4 Corticalis-Schrauben, ø 4,5 mm, 24 mm lang 3-212 4 Corticalis-Schrauben, ø 4,5 mm, 26 mm lang 3-214 4 Corticalis-Schrauben, ø 4,5 mm, 28 mm lang 3-216 4 Corticalis-Schrauben, ø 4,5 mm, 30 mm lang 3-218 4 Corticalis-Schrauben, ø 4,5 mm, 32 mm lang 3-220 4 Corticalis-Schrauben, ø 4,5 mm, 34 mm lang 3-222 3 Corticalis-Schrauben, ø 4,5 mm, 36 mm lang 3-224 2 Corticalis-Schrauben, ø 4,5 mm, 38 mm lang 3-226 1 Corticalis-Schrauben, ø 4,5 mm, 40 mm lang 3-604 1 Selbstspannende Knochenplatte, schmal, 4-Loch 3-606 1 Selbstspannende Knochenplatte, schmal, 5-Loch 3-608 1 Selbstspannende Knochenplatte, schmal, 6-Loch 3-610 1 Selbstspannende Knochenplatte, schmal, 7-Loch 4-204 1 Selbstspannende Knochenplatte, breit, 4-Loch 4-206 1 Selbstspannende Knochenplatte, breit, 5-Loch 4-208 1 Selbstspannende Knochenplatte, breit, 6-Loch 4-210 1 Selbstspannende Knochenplatte, breit, 7-Loch 4-212 1 Selbstspannende Knochenplatte, breit, 8-Loch 3-070 1 Biegeschablone, 5-Loch 3-071 1 Biegeschablone, 7-Loch 4-176 3 Unterlegscheibe, ø 7 mm 3-520 3 Unterlegscheibe, ø 11 mm 19E-267.05 1 Klein-Set-Container, grün, mit Deckel- und Bodenperforation, 300 x 140 x 100 mm 19E-353.04 1 Kennzeichnungsschild, blau 15-2150 1 Lagerungseinsatz 19E-137.01 1 Ein- bzw. Umschlagtücher T 313 1 Rack für ø 3,5 mm Schrauben T 316 1 Rack für ø 4,0 mm Schrauben T 317 1 Rack für ø 4,5 mm Schrauben VET.21

BASIS-SET 2 STARTER KIT 2 Repositionsinstrumente - Knochendraht Repostion Instruments - Bone wires V-2410 VET.22

BASIS-SET 2 STARTER KIT 2 Repositionsinstrumente - Knochendraht Repostion Instruments - Bone wires V-2410 9-596 2 Reposition forcpes with points, 135 mm 9-602 1 Reposition forcpes with points, 170 mm 9-580 2 Bone holding forceps, 150 mm 9-650 1 Bone lever, 150 mm 6 mm wide tip 9-652 1 Bone lever, 160 mm 8 mm wide tip 9-758 1 Raspatory, curved, 6 mm wide tip 9-093 1 Drilling chuck with key 7-418 1 Universal pliers 7-004 1 Cerclage wire, 0.4 mm diam., in coils of 10 m 7-008 1 Cerclage wire, 0.8 mm diam., in coils of 10 m 7-012 1 Cerclage wire, 1.2 mm diam., in coils of 10 m 7-200 10 KIRSCHNER wires, 70 mm, 0.8 mm diam. 7-252 10 KIRSCHNER wires, 150 mm, 1.0 mm diam. 7-254 10 KIRSCHNER wires, 150 mm, 1.2 mm diam. 7-260 10 KIRSCHNER wires, 150 mm, 1.6 mm diam. 7-378 1 Wire Tightner 19E-266.03 1 Small set container, red, with perforation in lid and bottom 300 x 140 x 70 mm 19E-353.04 1 Identification label, blue 15-2150 1 Storage wire base - Bone wires 15-2150 1 Storage wire base - Reposition Instruments 19E-137.01 2 Wrapping drapes 9-596 2 Repositionszangen mit Spitzen, 135 mm 9-602 1 Repositionszangen mit Spitzen, 170 mm 9-580 2 Selbstzentrierende Knochenhaltezangen, 150 mm 9-650 1 Knochenhebel, 150 mm, 6 mm breit 9-652 1 Knochenhebel, 160 mm, 8 mm breit 9-758 1 Raspatorium, abgebogen, 6 mm breit 9-093 1 Handbohrfutter mit Spannschlüssel 7-418 1 Drahtbiege- und Spannschlüssel 7-004 1 Cerclage Draht, ø 0,4 mm, Ring à 10 m 7-008 1 Cerclage Draht, ø 0,8 mm, Ring à 10 m 7-012 1 Cerclage Draht, ø 1,2 mm, Ring à 10 m 7-200 10 KIRSCHNER-Drähte, 70 mm, ø 0,8 mm 7-252 10 KIRSCHNER-Drähte, 150 mm, ø 1,0 mm 7-254 10 KIRSCHNER-Drähte, 150 mm, ø 1,2 mm 7-260 10 KIRSCHNER-Drähte, 150 mm, ø 1,6 mm 7-378 1 Drahtspanner 19E-266.03 1 Klein-Set-Container, rot, mit Deckel- und Bodenperforation 300 x 140 x 70 mm 19E-353.04 1 Kennzeichnungsschild, blau 15-2150 1 Lagereinsatz - Knochendraht 15-2150 1 Lagereinsatz - Repositionsinstrumente 19E-137.01 2 Ein- bzw. Umschlagtücher VET.23

AUFBAU-SET 2 ADVANCED SET 2 Instrumente für Schrauben mit Gewinde ø 3,5-4,5 mm sowie für die dazugehörigen Platten Instruments for screws with thread 3,5-4,5 mm diam. and for the belonging plates V-2412 VET.24

AUFBAU-SET 2 ADVANCED SET 2 Instrumente für Schrauben mit Gewinde ø 3,5-4,5 mm sowie für die dazugehörigen Platten Instruments for screws with thread 3,5-4,5 mm diam. and for the belonging plates V-2412 9-604 1 Reposition forceps with with points, 200 mm 9-582 2 Self centering bone holding, 190 mm 9-584 1 Self centering bone holding, 240 mm 9-660 1 Bone lever, 240 mm, 18 mm wide 9-656 1 Bone lever, 200 mm, 8 mm wide 9-750 1 Raspatory, straight, 14 mm wide 9-014 1 Twist drill, 2.0 diam AO 9-016 1 Twist drill, 2.5 diam AO 9-020 1 Twist drill, 3.2 diam AO 9-022 1 Twist drill, 3.5 diam AO 9-026 1 Twist drill, 4.5 diam AO 9-074 1 Tap, 3.5 mm diam. AO 9-076 1 Tap, 4.0 mm diam. AO 9-077 1 Tap, 4.5 mm diam. AO 9-102 1 Countersink, 2.7-4.0 mm diam. AO 9-106 1 Countersink, 4.5 mm diam. AO 9-144 1 Screw driver width across flats, 3.5 mm diam. 9-280 1 Insert sleeve for drills 3.2 mm diam. 9-256 1 Tissue protector sheath for drill and taps up to 3.5 mm diam. 9-260 1 Tissue protector sheath for drill and taps up to 4.5 mm diam. 9-259 1 Pointed drill guide 9-268 1 Drill guide for self-compressing bone plates suitable for drils with 2.5 mm diam. 9-270 1 Drill guide for self-compressing bone plates suitable for drils with 3.2 mm diam. 19E-266.01 1 Small set container, silver, with perforation in lid and bottom 300 x 140 x 70 mm 19E-353.04 1 Idenfication label, blue 15-2150 1 Storage wire base upper 15-2150 1 Storage wire base lower 19E-137.01 2 Wrapping drapes 9-604 1 Repositionszange mit Spitzen, 200 mm 9-582 2 Selbstzentrierende Knochenhaltezange, 190 mm 9-584 1 Selbstzentrierende Knochenhaltezange, 240 mm 9-660 1 Knochenhebel, 240 mm, 18 mm breit 9-656 1 Knochenhebel, 200 mm, 8 mm breit 9-750 1 Raspatorium gerade, 14 mm breit 9-014 1 Spiralbohrer, ø 2,0 mm AO Schaft 9-016 1 Spiralbohrer, ø 2,5 mm AO Schaft 9-020 1 Spiralbohrer, ø 3,2 mm AO Schaft 9-022 1 Spiralbohrer, ø 3,5 mm AO Schaft 9-026 1 Spiralbohrer, ø 4,5 mm AO Schaft 9-074 1 Gewindeschneider, ø 3,5 mm, AO Schaft 9-076 1 Gewindeschneider, ø 4,0 mm, AO Schaft 9-077 1 Gewindeschneider, ø 4,5 mm, AO Schaft 9-102 1 Kopfraumfräser, ø 2,7-4,0 mm AO Schaft 9-106 1 Kopfraumfräser, ø 4,5 AO Schaft 9-144 1 Schraubenzieher, SW 3,5 mm 9-280 1 Steckbohrbüchse für Bohrer ø 3,2 mm 9-256 1 Gewebeschutzhülse für Bohrer und Gewindeschneider bis ø 3,5 mm 9-260 1 Gewebeschutzhülse für Bohrer und Gewindeschneider bis ø 4,5 mm 9-259 1 Zielgerät mit Spitze 9-268 1 Spann- und Neutralbohrbüchse für Bohrer ø 2,5 mm 9-270 1 Spann- und Neutralbohrbüchse für Bohrer ø 3,2 mm 19E-266.01 1 Klein-Set-Container, silber, mit Deckel- und Bodenperforation 300 x 140 x 70 mm 19E-353.04 1 Kennzeichnungsschild, blau 15-2150 1 Lagerungseinsatz oben 15-2150 1 Lagerungseinsatz unten 19E-137.01 2 Umschlagtücher VET.25

Gleitnägel Intramedullary Gliding Nails Stainless Steel DIN ISO 5832-1 1-5250 1.5 x 150 mm 1-5251 1.5 x 400 mm 1-5252 2.0 x 200 mm 1-5253 2.0 x 400 mm 1-5254 2.5 x 250 mm 1-5255 2.5 x 400 mm 1-5256 3.0 x 300 mm 1-5257 3.0 x 400 mm 1-5258 3.5 x 350 mm 1-5259 3.5 x 400 mm Protective Caps availble according to diameter of nail Schutzkappen für Nägel passend zum Durchmesser des Nagels 1-5198 ø 1.5 mm 1-5200 ø 2.0 mm 1-5202 ø 2.5 mm 1-5204 ø 3.0 mm 1-5206 ø 3.5 mm 1-5208 ø 4.0 mm 1-5210 ø 4.5 mm 1-5212 ø 5.0 mm Principle / Prinzip: 2 Gliding Nails produce a 3-point support in an elastic and stable system. 2 Gleitnägel bilden eine 3-Punkt-Unterstützung für ein elastisches und stabiles System. VET.26

Trocar with slotted sleeve for implantation of medullary gliding nails After opening of the medullary canal with trocar, it happens quite often, that the point of entry cannot be found. By using the new trocar, the slotted sleeve remains in situ and avoids unnecessary searching or preparating of soft tissue. Gliding nails with bent tip can easily be introduced through the slot of the sleeve. Pfriem mit geschlitzter Hülse zur Implantation intramedullärer Schienen Häufig ensteht nach Eröffnung der Markhöhle mit einem Pfriem das Problem, die Eintrittsstelle wieder zu finden. Bei Verwendung des neuen Pfriems verbleibt die geschlitzte Hülse am vorgebohrten Loch und erspart unnötiges Suchen oder Freipräparieren der Weichteile. Durch die Schlitzung der Gewebeschutzhülse können Schienen mit gebogener Spitze leicht eingeführt werden. 1-5310 Trocar for ø 3,5-5,0 mm Nails 1-5312 Trocar for ø 1,5-3,5 mm Nails Opening of medullary cannal with trocar and sleeve Eröffnen der Markhöhle mit Pfriem und Hülse Removal of trocar. Sleeve is held in position Entfernen des Pfriems - die Hülse wird in der Position gehalten Introduction of nail through slot of sleeve Einführen der Schiene durch die geschlitzte Hülse VET.27

Einschlaginstrument für alle Gleitnägel-Durchmesser Impactor for all diameters of Gliding Nails Centering Sleeve Zentrierhülse Impactor head Schlagkopf Centering Sleeves for diam. Zentrierhülse für ø Handle Haltegriff 1-5320 1,5-2,0 mm 1-5322 2,5-3,0 mm 1-5324 3,5-5,0 mm Fixation Screw Feststellschraube 1-5316 Impactor Einschlaginstrument The new Impactor for Intramed Gliding Nails serves for quick introduction avoiding tiresome manipulating during fixation of implants. Owing to the lateral handle the danger of insuries to the surgeon in case of slipping-through of nails is practically impossible. A new clamping system serves for fixation of nails in the impactor without applying much power. Der neue Impactor für Intramed-Schienen ermöglicht das schnelle Einbringen von intramedullären Schienen ohne lästiges Hantieren bei der Fixation der Implantate. Durch den seitlichen Griff wird die Verletzungsgefahr für den Chirurgen, beim Durchrutschen der Schienen ausgeschlossen. Die Schienenfixation im Einschlaginstrument ist durch eine neuartige Verklemmung ohne großen Kraftaufwand möglich. VET.28

Pfriem 9-1450 Perthes, 22,0 cm 9-1452 Perthes, 16,0 cm Pfriem 9-1456 16,0 cm 1-5330 Extractions Forceps for Intramedullary Gliding Nails Extractionszange 22,0 cm für Intramed-Schienen 7-388 Extraction Pliers for boring wire 130 mm 7-390 Extraction Pliers for boring wire 180 mm VET.29

9-090 T-Handle with Jacobs Chuck T-Griff mit Jakobsfutter 1-5300 Nail Impactor ø 1,5-2,5 mm Einschläger ø 1,5-2,5 mm 1-5302 Nail Impactor ø 2,5-3,0 mm Einschläger ø 2,5-3,0 mm 1-5304 Nail Impactor ø 3,5-5,0 mm Einschläger ø 3,5-5,0 mm 9-701 Slotted Hammer Schlitzhammer 9-702 Bone Hammer / Weight approx: 350 g Knochenhammer / Gewicht ca 350 gr. VET.30

7-434 Wire Cutter 220 mm TC soft wire 3.0 mm hard wire 2.5 mm Drahtschneidezange 220 TC für weichen Draht bis ø 2,5 mm für harten Draht bis ø 3,0 mm 7-452 260 mm hard wire 3.5 mm Kopfschneider für harten Draht bis ø 3,5 mm 7-450 575 mm hard wire 6.0 mm Bolzenschneider für harten Draht bis ø 6,0 mm VET.31

Aus Drahtgeflecht Wire Mesh En fil inox De alambre In rete metallica 580 x 280 x 100 mm Silver Silber 19E-100.01 19E-129.01 540 x 255 x 50 mm Recommended Instruments 19E-100.01 Sterile-Container 580 x 280 x 100 mm 19E-129.01 Basket for Instruments 540 x 255 x 50 mm 1-5310 Trocar for 3,5-5,0 mm 1-5312 Trocar for 1,5-3,0 mm 1-5316 Impactor complete 1-5300 Impactor for nail 1,5-2,0 mm 1-5302 Impactor for nail 2,5-3,0 mm 1-5304 Impactor for nail 3,5-5,0 mm 9-701 Slotted Hammer 9-702 Hammer 350 gr. 1-5330 Extraction Forceps 22,0 cm 16E-525.22 Wire Cutter for wire ø 2,5 mm 7-452 Wire Cutter for wire ø 3,5 mm 7-450 Wire Cutter for wire ø 6,0 mm Empfohlene Instrumente 19E-100.01 Steril-Container 580 x 280 x 100 mm 19E-129.01 Drahtkorb für Instrumente 540 x 255 x 50 mm 1-5310 Trokar für 3,5-5,0 mm 1-5312 Trokar für 1,5-3,0 mm 1-5316 Einschläger komplett 1-5300 Einschläger für Nägel 1,5-2,0 mm 1-5302 Einschläger für Nägel 2,5-3,0 mm 1-5304 Einschläger für Nägel 3,5-5,0 mm 9-701 Schlitzhammer 9-702 Hammer 350 gr. 1-5330 Extraktionszange 22,0 cm 16E-525.22 Drahtschneidezange für Draht ø 2,5 mm 7-452 Drahtschneidezange für Draht ø 3,5 mm 7-450 Drahtschneidezange für Draht ø 6,0 mm VET.32

Kirschner Wires Point Trocar Trocar Shaft End round Trocar Length 310 mm 310 mm ø 1.0 mm 7-120 7-140 ø 1.2 mm 7-121 7-141 ø 1.4 mm 7-122 7-142 ø 1.5 mm 7-123 7-143 ø 1.6 mm 7-124 7-144 ø 1.8 mm 7-126 7-145 ø 2.0 mm 7-127 7-146 ø 2.2 mm 7-128 7-147 ø 2.5 mm 7-129 7-148 ø 3.0 mm 7-130 Point Trocar Trocar Trocar Shaft End round round Trocar Length 70 mm 150 mm 150 mm ø 0.8 mm 7-200 7-250 7-280 ø 1.0 mm 7-201 7-252 7-282 ø 1.2 mm 7-254 7-284 ø 1.4 mm 7-256 7-286 ø 1.5 mm 7-208 7-258 7-288 ø 1.6 mm 7-260 7-290 ø 1.8 mm 7-262 7-292 ø 2.0 mm 7-264 7-294 ø 2.2 mm 7-266 7-296 ø 2.5 mm 7-210 7-268 7-298 ø 3.0 mm 7-270 VET.33

Kirschner Wires with thread and trocar points, round end Diameter Length Threaded Length 7-310 1.6 mm 150 mm 5 mm 7-312 1.6 mm 150 mm 15 mm 7-314 2.0 mm 150 mm 15 mm 7-316 2.0 mm 200 mm 15 mm 7-318 2.5 mm 200 mm 15 mm 7-320 2.5 mm 230 mm 20 mm 7-350 Bending Iron for Kirschner Wires 7-353 Pliers with serrated jaws and groove 7-356 Pliers with serrated jaws without groove 7-358 Rounded Pliers with serrated jaws VET.34

Wire Drill Dispenser easy to transport and storage - silicone insert avoids damiging the wire tips Wire length Wire ø 0,8 mm Wire ø 1,0 mm Wire ø 1,2 mm Wire ø 1,4 mm Wire ø 1,6 mm Wire ø 2,0 mm Wire ø 2,2 mm Wire ø 2,5 mm 16,0 cm 7-850 7-852 7-854 7-856 7-858 7-860 7-862 7-864 31,0 cm 7-870 7-872 7-874 7-876 7-878 7-880 7-882 7-884 This specially designed dispender holds four different wire gauges ø 1.0 / 1.2 / 1.4 / and 1.6 mm, each 10 cm long. 7-890 Vickers Easidriver 7-892 Wire Drill Dispenser VET.35

Metall Rack for Kirschner Wires Metall Rack for Kirschner Wires For storage and sterilization of Kirschner Wires for different sizes 310 mm 7-840 for 8 different sizes 150 mm 7-842 3 different sizes for Kirschner Wires, 10 cm, 16 cm, 31 cm made of stainless material, sterilizable - 134 for 4, 6, 8 and 10 different diameters each each compartment can receive from 6 up to 20 Kirschner Wires (depending on the diameters) with special Silicon strip to protect the wire tips with integrated measuring gauge VET.36

Standard T 250 Fixateur Satz Cat. Nr. Beschreibung Stück 8-2506 erbrich-fix Nr. I 1 8-2510 erbrich-fix Nr. II 1 8-2520 erbrich-fix Nr. III 1 8-2522 Teflon Steri Etui 1 8-2530 Ersatzspindeln 40 mm 1 8-2532 Ersatzspindeln 50 mm 1 8-2534 Ersatzspindeln 60 mm 1 8-2536 Ersatzfeststellschrauben 20 8-0342 Inbusschlüssel 1,5 mm 1 8-0339 Inbusschlüssel 4,0 mm 1 8-2540 Schraubendreher 1 8-2550 Haltebolzen schmal 1 8-2552 Haltebolzen breit 1 7-300 Kirschnerdrähte ø 1,8 mm 70 mm lang, 30 mm Gewinde 12 7-301 Kirschnerdrähte ø 1,6 mm 70 mm lang, 30 mm Gewinde 12 zusätzlich empfohlene Instrumente: 8-2560 Haltezange 1 7-430 Zwickzange 1 7-432 Zwickzange 1 7-388 Kirschner Extraktionszange 130 mm 1 7-390 Kirschner Extraktionszange 180 mm 1 7-400 Ausziehzange Chrom Vanadium 1 7-402 Ausziehzange rostfrei 1 Standard T 250 Fixateur Set Cat. No. Description Pieces 8-2506 erbrich-fix No. I 1 8-2510 erbrich-fix No. II 1 8-2520 erbrich-fix No. III 1 8-2522 Teflon Steri Box 1 8-2530 Threaded Rod 40 mm 1 8-2532 Threaded Rod 50 mm 1 8-2534 Threaded Rod 60 mm 1 8-2536 Fixation Screws 20 8-0342 Allen Key 1.5 mm 1 8-0339 Allen Key 4.0 mm 1 8-2540 Screw Driver 1 8-2550 Holding Lever small 1 8-2552 Holding Lever wide 1 7-300 Kirschner Wire ø 1.8 mm 70 mm long, thread 30 mm 12 7-301 Kirschner Wire ø 1.6 mm 70 mm long, thread 30 mm 12 Recommended Instruments 8-2560 Holding Forceps 1 7-430 Wire Cutter 1 7-432 Wire Cutter 1 7-388 Kirschner Wire Extracting Pliers 130 mm 1 7-390 Kirschner Wire Extracting Pliers 130 mm 1 7-400 Flat Nose Parallel Pliers Chrome Vanadium 1 7-402 Flat Nose Parallel Pliers stainless steel 1 VET.37

8-2506 erbrich-fix Nr. I erbrich-fix No. I 8-2510 erbrich-fix Nr. II erbrich-fix No. II 8-2520 erbrich-fix Nr. III erbrich-fix No. III 7-300 Kirschnerdraht mit Gewinde und Trokarspitze ø 1,8 mm, 70 mm lang, 30 mm Gewinde Kirschner Wire with thread and trocar point ø 1.8 mm, 70 mm long, 30 mm thread 7-301 Kirschnerdraht mit Gewinde und Trokarspitze ø 1,6 mm, 70 mm lang, 30 mm Gewinde Kirschner Wire with thread and trocar point ø 1.6 mm, 70 mm long, 30 mm thread VET.38

Small External Fixateur T 806 Small External Fixateur 19E-261.04 Small Aluminium Case, blue, perforated 300 x 140 x 70 mm 15-2115 Trays for small instruments (2 pieces) 9-014 Drill Bit 2.0 mm 2 pieces 9-016 Drill Bit 2.5 mm 2 pieces 8-0934 Combination Wrench width across flats 7 mm 1 piece 8-0246 Socket Wrench 7 mm 1 piece 8-0248 Drill Sleeve complete 1 piece 8-0210 - Connecting Bars 24 pieces 2 each: 60-160 - 180-200 mm 8-0217 4 each: 80-100 - 120-140 mm 8-0240 Clamps Open 4 pieces 8-0242 Clamps 12 pieces 8-0256 Springloaded Nut 2 pieces 8-0250 Schanz Screw 4.0 x 3.0 mm 4 pieces 7-260 Kirschner Wire 1.6 x 150 mm 10 pieces 7-264 Kirschner Wire 2.0 x 150 mm 10 pieces 7-315 Kischner Wire with Thread 15 mm, 2.5 x 150 mm 10 pieces VET.39

Small External Fixater Set 9-014 Dril Bit 2.0 mm 9-016 Dril Bit 2.5 mm 8-0934 Combination Wrench, width across flats, 7 mm 8-0248 Drill Sleeve complete 8-0246 Socket Wrench, width across flats, 7 mm 8-0250 Drill Sleeve 5.0 / 4.0 mm 8-0251 Drill Sleeve 5.0 / 4.0 mm 8-0252 Trokar, ø 2.7 mm Connecting Bars, 4.0 mm diam. stainless steel 8-0210 60 mm 8-0211 80 mm 8-0212 100 mm 8-0213 120 mm 8-0214 140 mm 8-0215 160 mm 8-0216 180 mm 8-0217 200 mm 8-0240 Clamp Open 2.5-5.0 mm ø 8-0242 Clamp 2.5-5.0 mm ø 8-0244 Open Compressor 8-0254 Schanz Screws ø 4.0 / 3.0 mm - 80 mm 8-0255 Schanz Screws ø 4.0-80 mm 8-0256 Springloaded Nut VET.40

Schanz Screws for external Fixation 24-180 Shaft ø 2,4 mm Threaded ø 3,2 mm Length 100 mm 24-182 Shaft ø 3,2 mm Threaded ø 4,0 mm Length 120 mm 24-184 Shaft ø 4,0 mm Threaded ø 4,8 mm Length 150 mm 24-190 Shaft ø 2,4 mm Threaded central ø 3,2 mm Length 100 mm 24-192 Shaft ø 3,2 mm Threaded central ø 4,0 mm Length 120 mm 24-194 Shaft ø 4,0 mm Threaded central ø 4,8 mm Length 150 mm VET.41

Cerclage Wire soft, in coils of 10 m ø mm Gauge Cat. No.: 0.2 31 7-002 0.3 29 7-003 0.4 27 7-004 0.5 25 7-005 0.6 23 7-006 0.7 22 7-007 0.8 21 7-008 0.9 20 7-009 1.0 19 7-010 1.2 18 7-012 1.5 17 7-015 Cerclage Wires with eye, soft Diameter Length 7-020 0.8 mm 280 mm 7-022 1.0 mm 280 mm 7-023 1.2 mm 280 mm 7-024 1.0 mm 600 mm 7-025 1.2 mm 600 mm 7-380 Wire Tightener 7-030 Parham Martin Band Tightener 7-032 Parham Metal Bone Bands 19 cm x 0.5 mm VET.42

16E-041 Loute 22 cm Bone Wire Tightener 7-372 Demel 28 cm Bone Wire Tightener 7-375 Wire Guide 45 mm 7-377 Wire Guide 70 mm 7-378 Wire Tightener VET.43

7-388 Extraction Pliers for boring wire 130 mm 7-390 Extraction Pliers for boring wire 180 mm 16E-511.01 16E-510.03 Extraction Pliers for wire 18,0 cm Extraction Pliers TC jaws 16E-505.18 16E-505.20 16E-505.24 Vise Grip 18,0 cm Stainless Steel Vise Grip 20,0 cm Stainless Steel Vise Grip 24,0 cm Stainless Steel 16E-500.19 16E-501.19 Flat-nosed Pliers, parallel, without lateral Wire Cutter, 18,0 cm Stainless Steel Flat-nosed Pliers, parallel, with lateral Wire Cutter, 18,0 cm Stainless Steel VET.44

Extraction Instruments 7-404 Extraction Pliers, 190 mm TC 7-406 Extraction Pliers, 200 mm TC VET.45

16E-047 Universal Scissors 21E-159 Universal Scissors with TC cutting edges 7-414 Wire Cutter 7-416 Wire Tightening Pliers TC 7-418 Wire Bending Pliers soft wire 1.5 mm hard wire 1.0 mm 7-420 Wire Bending Cutting Pliers soft wire 1.5 mm hard wire 1.0 mm 7-422 Wire Cutter soft wire 2.0 mm hard wire 1.2 mm VET.46

Wire Cutters 16E-525.18 TC 18,0 cm soft wire 2.0 mm hard wire 1.5 mm 16E-530.18 18,0 cm frontal and lateral cutting action TC soft wire 2.0 mm hard wire 1.5 mm 16E-525.22 Wire Cutter 22,0 cm TC soft wire 3.0 mm hard wire 2.5 mm 16E-527.15 16E-527.22 Wire Cutter 15,0 cm TC soft wire 1.5 mm Wire Cutter 22,0 cm TC soft wire 2.5 mm hard wire 2.2 mm 7-438 Wire Cutter TC 140 mm soft wire 1.2 mm hard wire 0.8 mm VET.47

Diamond Pin Cutter 16E-524.19 Wire Cutter cannulated 18,0 cm soft wire 2.4 mm hard wire 1.6 mm 7-443 Wire Cutter Hard Wire 2.0 mm 7-441 Wire Cutter TC Hard Wire 1.2 mm VET.48

Wire Cutters 7-444 Cutter for cutting of Kirschner wires Steinmann Pins up to 6 mm ø hard 540 mm TC 7-446 Cutter for cutting of Kirschner wires Steinmann Pins up to 6 mm ø hard 460 mm TC 7-450 575 mm Hard wire 6.0 mm 7-452 260 mm Hard wire 3.5 mm VET.49

Staples - Chrome Cobalt Molybden 5-650 6 mm 5-652 8 mm 5-654 11 mm 5-656 14 mm 5-670 Impactor Diameter Width Length 5-620 2.5 mm 22 mm 19 mm 5-622 2.5 mm 16 mm 19 mm 5-624 1.5 mm 22 mm 19 mm 5-626 1.5 mm 16 mm 19 mm 5-630 Staples Extractor 5-632 Staples Driver 5-634 Staples Inserter VET.50

Drill Bits ø mm AO shaft Length mm round shaft Length mm 1.1 9-010 60 / 35 9-040 45 / 30 1.5 9-012 85 / 60 9-042 70 / 55 2.0 9-014 100 / 75 9-044 85 / 70 2.5 9-016 110 / 85 9-046 95 / 80 2.7 9-018 100 / 75 9-048 85 / 70 3.2 9-020 145 / 120 9-050 130 / 115 3.2 9-021 195 / 170 9-051 180 / 165 3.5 9-022 100 / 85 9-052 95 / 80 3.5 9-023 195 / 170 9-053 180 / 165 4.5 9-026 145 / 120 9-056 130 / 115 4.5 9-027 195 / 170 9-057 180 / 165 Taps for screws ø mm AO shaft T-bar 1.5 dental 9-071 2.0 dental 9-072 2.7 9-073 9-060 3.5 thread pitch 1.25 9-074 9-062 3.5 thread pitch 1.75 9-075 9-064 4.0 thread pitch 1.75 9-076 9-065 4.5 short thread 9-077 4.5 long thread 9-078 9-068 6.5 9-079 9-070 VET.51

Drill Bit and Tap Handles (Complete) 9-090 Tap Handle for Jacobs Chuck Consisting of: 9-089 T-Handle 9-091 Jacobs Chuck 9-0910 Wrench for Jacobs Chuck VET.52

Drill Bit and Tap Handles 9-092 Tap Handle for AO shaft 9-093 T-Handle chuck and key, fully cannulated, accept items up to diameter of 4,5 mm 9-094 Tap Handle for AO shaft 9-096 Tap Handle for Dental shaft VET.53

Instruments for Screw Fixation Countersinks For preparing the seat for the screw head 9-100 For Mini Screws 1.5 mm and 2.0 mm ø Tip 1.1 mm ø 9-102 For Small Screws 2.7, 3.5 and 4.0 mm ø Tip 2.0 mm 9-104 For Malleolar Screws Tip 3.2 mm ø 9-106 For Large Screws 4.5 mm and 6.5 mm ø Tip 4.5 mm 9-110 Depth Gauge for Mini Screws 9-112 Depth Gauge for Small Screws 9-114 Depth Gauge for Large Screws 4-184 Screw Forceps 9-116 Sharp Hook for checking alignment of fracture ends and for removing in-grown tissue in screw heads VET.54

Screw Drivers 9-140 for Hexagonal Head 1.5 mm, 20 cm length 9-142 for Hexagonal Head 2.5 mm, 20 cm length 9-144 for Hexagonal Head 3.5 mm, 20 cm length 9-148 for Philips Head 20 cm length 9-150 for Single Head 20 cm length 9-152 Slotted Head 20 cm length A B C D 9-158 A Screw Driver Williams for Phillips Head 9-160 B Screw Driver Williams for Slotted Head 9-162 C Screw Driver Williams for Single Head 9-164 D Screw Driver Williams for Hexagonal Head 3.5 mm VET.55

Instruments for Screw Fixation 9-170 Screw Driver for Mini Screws 1.5 mm 9-171 Holding Sleeve 1.5 mm 9-172 Screw Driver 2.5 mm 9-173 Holding Sleeve 2.5 mm 9-174 Screw Driver Shaft 2.5 mm 9-176 Screw Driver Shaft 1.5 mm 9-178 Screw Driver Shaft 1.5 mm VET.56

Instruments for Screw Fixation Drill Sleeves and Drill Guides 9-250 MIni Drill Sleeve Drill Bit 1.1 and 1.5 mm ø 9-253 MIni Drill Sleeve Drill Bit 1.5 and 2.0 mm ø 9-252 Drill Guide and Drill Sleeve, 2.0 mm ø with 3 and 1 hole respectively Drill Bit 2.0 mm ø 9-254 Tap Sleeve 3.5 mm ø Drill Sleeve 2.5 mm ø for Drill Bit and Tap for 3.5 mm Cortex Screws with fine thread 9-255 Tap Sleeve 2.7 mm ø Drill Sleeve 2.0 mm ø for Drill Bit and Tap for 3.5 mm Cortex Screws with fine thread 9-256 Tap Sleeve 3.5 mm ø for Taps 3.5 and 2.7 mm ø May also be used as a Guide for 3.2 mm ø Drill Bits 9-258 Pointed Drill Guide VET.57

Instruments for Screw Fixation 9-260 Tap Sleeve 4.5 mm ø For Taps 6.5 mm ø May also be used as Drill Guide for 4.5 mm Drill Bits The notched tip prevents slipping on the bone Use Sleeve 8 mm ø in the screw holes of plates 9-262 Drill Guides for Round-Hole Plates for Drill Bit 3.2 mm ø Standard, 40 mm 9-266 Neutral and Load Drill Guide, 2.0 mm For 2.0 mm screws Use Drill Bit 1.5 mm ø 9-268 Neutral and Load Drill Guide, 2.7 mm For 2.7 mm screws Use Drill Bit 2.0 mm ø 9-270 Neutral and Load Drill Guide, 3.5 / 1.25 mm For 3.5 mm Cortex Screws with fine thread Use Drill Bit 2.5 mm ø 9-272 Neutral and Load Drill Guide, 4.5 mm For 4.5 mm screws Use Drill Bit 3.2 mm ø 9-276 Insert Drill Sleeve 2.7 / 2.0 mm ø For 2.7 mm Cortex Lag Screws Drill Bit 2.0 mm ø 9-278 Insert Drill Sleeve 3.5 / 2.5 mm ø For 3.5 mm Cortex Lag Screws Drill Bit 2.5 mm ø 9-280 Insert Drill Sleeve 4.5 / 3.2 mm ø For 3.5 mm Cortex Lag Screws with fine thread Drill Bit 3.2 mm ø 9-284 C-Clamp Drill Guide with thread for Drill Bit 4.5 mm ø VET.58

17-1420 Bending Templates for curved Reconstruction Plates 4.5 mm 17-1422 Bending Templates for straight Reconstruction Plates 4.5 mm 17-1424 Bending Templates for curved Reconstruction Plates 3.5 mm 17-1426 Bending Templates for straight Reconstruction Plates 3.5 mm 17-1400 Bending Pliers for 2.7 mm and 3.5 mm Plates 17-1404 Bending Iron for 3.5 mm and 4.5 mm Plates 17-1430 Osteotomy Chisels 304 mm 15 mm 17-1432 Osteotomy Chisels 304 mm 20 mm VET.59

Bending Instruments for Plates 9-400 Bending Iron for Mini and Finger Plates 9-402 Bending Iron for 3.5 mm Reconstruction Plates 9-404 Bending Iron for 2.7 mm Reconstruction Plates 9-406 Bending Pliers for 1.5 and 2.0 mm Plates 16E-580.24 16E-580.20 Bending Pliers for 2.7 and 3.5 mm Plates, 24,0 cm Bending Pliers for 1.0 and 2.0 mm Plates, 20,0 cm 9-410 Bending Pliers VET.60

16E-033 Kern Baby Bone Holding Forceps 17,0 cm with ratchet 16E-031 Kern Baby Bone Holding Forceps 18,0 cm without ratchet 16E-034 Kern Bone Holding Forceps 21,0 cm with ratchet 16E-032 Kern Bone Holding Forceps 21,0 cm without ratchet 16E-029 Lane Bone Holding Forceps 33,0 cm with ratchet 16E-027 Lane Bone Holding Forceps 33,0 cm without ratchet 16E-028 Lane Bone Holding Forceps 45,0 cm without ratchet 16E-030 Lane Bone Holding Forceps 45,0 cm with ratchet 9-520 Farabeuf-Lambotte Bone Holding Forceps 260 mm with ratchet 9-522 Farabeuf-Lambotte Bone Holding Forceps 260 mm without ratchet 16E-232 Lambotte Bone Holding Forceps 22,0 cm 16E-233 Lambotte Bone Holding Forceps 26,0 cm 16E-234 Lambotte Bone Holding Forceps 32,0 cm VET.61

Self-Centering Bone Holding Forceps with Thread Lock 9-580 For Small Fragments 150 mm, jaw 9 mm 9-582 Size 0 190 mm, extra small jaw 10 mm 9-584 Size 1 240 mm, small jaw 14 mm 16E-039 Verbrügge Bone Holding Forceps 17,5 cm 16E-040 Verbrügge Bone Holding Forceps 25,0 mm 9-562 Reduction Forceps with Thread Lock 160 mm VET.62

ULRICH 9-638 straight, with speed lock 190 mm 9-592 Semb 200 mm 9-594 Semb 200 mm with ratchet 9-596 Reposition Forceps for Small Fragments 135 mm 9-600 Forceps with Ratchet Fixation 145 mm 9-602 Reil 170 mm 9-630 Holding Forceps for Mini 135 mm VET.63

9-610 Lowmann Bone Clamp 130 mm 9-612 Lowmann Bone Clamp 185 mm 9-614 Lowmann Bone Clamp 200 mm 9-618 Reposition Forceps 230 mm VET.64

9-632 Ulrich 230 mm 9-634 Ulrich 250 mm 9-636 Ulrich 280 mm 9-640 Ulrich 260 mm VET.65

Standard Retractors 9-650 Small, width 6 mm short, narrow tip 9-652 Small, width 8 mm short, narrow tip 9-654 For Small Fragments with broad shank 9-656 Width 8 mm short, narrow tip VET.66 9-658 width 18 mm short, narrow tip 9-660 width 18 mm long, narrow tip 9-666 width 43 mm narrow tip 9-668 width 70 mm narrow tip 9-670 width 43 mm long shank, angled

Periosteal Elevators with synthetic handle, autoclavable 9-750 Medium straight blade round edge, width 14 mm 9-752 medium curved blade round edge, width 14 mm 9-754 large straight blade round edge, width 30 mm 9-756 Small curved blade round edge, width 6 mm 9-758 Small curved blade straight edge, width 6 mm 9-760 Extra small curved blade straight edge, width 3 mm VET.67

9-768 Chisel Blade 10 mm 9-770 Chisel Blade 16 mm 9-772 Chisel Blade 25 mm 9-774 Chisel Blade 5 mm 9-766 Chisel Handle 9-776 Wrench for Chisel Handle Mini-Lambotte 9-778 170 mm length 2 mm width 9-780 170 mm length 5 mm width 9-782 170 mm length 10 mm width straight 9-790 5 mm 9-792 10 mm 9-794 15 mm curved 9-796 5 mm 9-798 10 mm 9-800 15 mm flat 9-802 10 mm 9-804 15 mm 9-806 20 mm 9-808 25 mm hollow 9-814 10 mm 9-816 15 mm 9-818 20 mm 9-820 25 mm VET.68

Chisels, Gouges and Osteotomes Jansen, 14,0 cm 16E-083.04 4 mm 16E-083.06 6 mm 16E-083.08 8 mm 16E-083.10 10 mm 16E-083.12 12 mm Jansen, 14,0 cm 16E-084.04 4 mm 16E-084.06 6 mm 16E-084.08 8 mm 16E-084.10 10 mm 16E-084.12 12 mm Jansen, 14,0 cm 16E-085.04 4 mm 16E-085.06 6 mm 16E-085.08 8 mm 16E-085.10 10 mm 16E-085.12 12 mm HOKE, 13,5 cm 16-286 3 mm 16-288 5 mm 16-290 6 mm 16-292 8 mm 16-294 9 mm LUCAS, 16,0 cm 16-296 4 mm 16-298 6 mm LUCAS, 16,0 cm 16-300 3 mm 16-302 5 mm VET.69

Chisels, Gouges and Osteotomes ALEXANDER, 18,0 cm 16E-074 4 mm 16E-075 6 mm 16E-076 8 mm 16E-077 10 mm 16E-078 12 mm 16E-079 14 mm ALEXANDER, 18,0 cm 16E-080 4 mm 16E-081 6 mm 16E-082 8 mm 16E-083 10 mm 16E-084 12 mm 16E-085 14 mm PARTSCH, 13,5 cm 16E-115 2 mm 16E-116 3 mm 16E-117 4 mm 16E-118 5 mm 16E-119 6 mm 16E-120 7 mm 16E-121 8 mm PARTSCH, 17,0 cm 16E-122 2 mm 16E-123 3 mm 16E-124 4 mm 16E-125 5 mm 16E-126 6 mm 16E-127 7 mm 16E-128 8 mm PARTSCH, 13,5 cm 16E-136 2 mm 16E-137 3 mm 16E-138 4 mm 16E-139 5 mm 16E-140 6 mm 16E-141 7 mm 16E-142 8 mm PARTSCH, 17,0 cm 16E-143 2 mm 16E-144 3 mm 16E-145 4 mm 16E-146 5 mm 16E-147 6 mm 16E-148 7 mm 16E-149 8 mm VET.70

STILLE 16E-150 10 mm 16E-151 15 mm 16E-152 20 mm 16E-153 25 mm STILLE 16E-154 10 mm 16E-155 15 mm 16E-156 20 mm 16E-157 25 mm STILLE 16E-158 10 mm 16E-159 15 mm 16E-160 20 mm 16E-161 25 mm 16E-060 Lambotte 15 mm 16E-061 Lambotte 20 mm 16E-062 Lambotte 25 mm 16E-063 Lambotte 30 mm 16E-064 Lambotte 38 mm 16E-065 Lambotte 44 mm 16E-066 Lambotte 50 mm 16E-067 Lambotte curved 15 mm 16E-068 Lambotte curved 20 mm 16E-069 Lambotte curved 25 mm 16E-070 Lambotte curved 30 mm 16E-071 Lambotte curved 38 mm 16E-072 Lambotte curved 44 mm 16E-073 Lambotte curved 50 mm VET.71

Chisels, Periosteal Raspatories Mini-Lexer, 18,0 cm 16E-086 4 mm 16E-087 6 mm 16E-088 8 mm 16E-089 10 mm 16E-090 12 mm Mini-Lexer, 18,0 cm 16E-091 4 mm 16E-092 6 mm 16E-093 8 mm 16E-094 10 mm 16E-095 12 mm 9-964 Langenbeck 18 cm 9-966 Langenbeck 19 cm 9-968 Farabeuf 9-970 Farabeuf 9-972 5 mm 9-974 6 mm 9-976 7 mm VET.72

Peristeal Raspatories, Bone Curettes 9-980 Lambotte 10 mm 9-982 Lambotte 15 mm 9-984 Lambotte 20 mm Fig. 0000 16E-017.40 Fig. 000 16E-017.30 Fig. 00 16E-017.20 Fig. 0000 9-1000 Fig. 000 9-1002 Fig. 00 9-1004 Fig. 0 16E-017.10 Fig. 1 16E-017.01 Fig. 2 16E-017.02 Fig. 0 9-1006 Fig. 1 9-1008 Fig. 2 9-1010 Fig. 3 9-1012 Fig. 4 9-1014 Fig. 5 9-1015 Fig. 3 16E-017.03 Fig. 4 16E-017.04 Fig. 5 16E-017.05 Spratt Bruns Fig. 6 16E-017.06 VET.73

Amputation Retractor and Saws 9-1280 Percy Retractor 16E-020 Charrière 30 cm 16E-021 Satterlee 31 cm 9-1290 Charrière 35 cm VET.74

9-1252 Gigli Handle 9-1260 Gigli Saw, stainless 30 cm 9-1262 Gigli Saw, stainless 40 cm 9-1264 Gigli Saw, stainless 50 cm 9-1266 Gigli Saw, stainless 70 cm 05E-012 De Martel 31 cm, Saw Guide VET.75

16-504 16-506 COTTLE 16-500 21,0 cm FOMON 16-502 21,0 cm AUFRICHT 21,0 cm 16-510 fine 16-510 coarse MALTZ 16-508 18,0 cm LEWIS 18,0 cm VET.76

FOMON 20,0 cm 16-520 16-522 16-524 16-526 16-528 VET.77

Bone Cutting Forceps Cleveland 16E-222 15,0 cm Cleveland 16E-223 17,0 cm 9-1317 12,0 cm LISTON 16E-214 14,0 cm 16E-218 16E-215 17,0 cm 16E-219 16E-216 19,0 cm 16E-220 16E-217 22,0 cm 16E-221 LITTAUER-LISTON 9-1318 15,0 cm VET.78

Bone Cutting Forceps 16E-228 Ruskin-Liston 18,0 cm straight 16E-229 Ruskin-Liston 18,0 cm curved 16E-230 Stille-Liston 27,0 cm straight 16E-231 Stille-Liston 27,0 cm curved 9-1336 Stille Horsley 270 mm 9-1340 Stille Semb 270 mm 16E-225 Böhler 15,0 cm straight 16E-226 Böhler 15,0 cm curved VET.79

Bone Rongeurs 16E-206 9-1377 9-1373 16E-207 9-1374 BÖHLER 15,0 cm KLEINERT-KUTZ 15,0 cm RUSKIN-MINI 9-1375 15,0 cm BEYER 9-1380 18,0 cm ZAUFAL-JANSEN 16E-211 18,0 cm RUSKIN 16E-201 18,0 cm VET.80

Bone Rongeur Forceps 16E-184 Luer 17,0 cm straight 16E-185 Luer 17,0 cm curved 16E-197.01 16E-197.02 Lempert 16,0 cm straight Lempert 19,0 cm straight 16E-197.02 16E-197.06 Lempert 16,0 cm curved Lempert 18,5 cm curved VET.81

Awls and Files 9-1450 Perthes, 22,0 cm 9-1452 Perthes, 16,0 cm 9-1454 15,0 cm 9-1456 16,0 cm 9-1470 Putti, 30,0 cm 9-1472 Putti, 28,0 cm VET.82

Bone Hammers 9-700 ø 30 mm / 215 g with interchangeable plastic disks 250 mm 9-701 Pair of spare disks 9-702 Weight approx: 350 g 9-704 Weight approx: 500 g (Standard size) 9-706 Weight approx: 700 g (For Medullary Nailing) 16E-271 ø 42 mm, 250 mm Material Ferrozell can be sterilized in an autoclave at 3 bar overpressure (143 C) 16E-270 18,0 cm length, ø 30 mm, 125 g (4 oz) Material Ferrozell can be sterilized in an autoclave at 3 bar overpressure (143 C) VET.83

Bone Hammers WILLIGER, 24,0 cm 9-712 ø 26 mm, 300 gr. 9-714 ø 28 mm, 340 gr. 9-716 ø 30 mm, 400 gr. DOYEN, 20,0 cm 9-718 ø 25 mm, 120 gr. 9-720 ø 30 mm, 180 gr. 9-722 ø 35 mm, 260 gr. COTTLE, 19,0 cm 9-724 240 gr. VET.84

Bone Hammers THIESS, 16,5 cm 9-726 ø 20 mm, 140 gr. lead filled 9-728 ø 20 mm, 140 gr. brass, solid MEAD, 17,0 cm 9-728 ø 26 mm, 320 gr. LUCAE, 19,0 cm 9-730 ø 19 mm, 230 gr. 9-732 ø 25 mm, 260 gr. PARTSCH, 18,0 cm 9-734 ø 22 mm, 200 gr. VET.85

Universal Bone Drills 14-011 Wrench 14-010 Bunnell Small Hand Drill, cannulated for Kirschner Wires, with 3 - jaw chuck, to fit any size of shanks up to 4.0 mm diameter, 160 mm 14-012 Ralk Hand Drill light metal case and laterally angled handle, with 3 - jaw chuck and key, opening up to 6.35 mm diameter 14-014 Ralk 6.35 mm capacity This widely used hand drill has a two-to-one gear ratio to ensure accurate drilling. The comfortable pistol grip handle gives the user perfect control. Release of the thumb operated lever, conveniently placed, instantly stops the turning of the gears and locks the chuck. The chuck shaft, and the entire length of the drill is cannulated to accommodate Steinmann Pins, Kirschner Wires, Long Shank Drills and Screw Driver Bits. VET.86

14-020 Adjustable Handle Hand Drill, stainless, as above, but equipped with an orginal Jakobs chuck and key. Can be used with or without the key, 280 mm 14-022 Surgery Hand Motor, 220 V a. c., with 3 - jaw chuck and key accomodating up to 6.35 mm, removable and sterilizable 14-024 same as above but for 110 V VET.87

14-806 Akku-Bohrmaschine mit Jacobs Futter ( enthalten 1 Stück : 14-807 / 14-830 ) Battery-driven drill with Jacobs chuck: ( include 1 piece : 14-807 / 14-830 ) 14-807 Akku-Bohrmaschine mit Verschlußdeckel ( ohne Akku ) Battery-driven drill with closure cover ( without battery ) VET.88

Übersicht von Zubehör : Overview for accessories : 14-810 Akku Battery 14-814 Ladegerät / Tisch 220 V für 1 Batterie Charger / bench 220 V for 1 batterie 14-815 Ladegerät / Tisch 110 V für 1 Batterie Charger / bench 110 V for 1 batterie 14-816 Ladegerät / Tisch 220 V für 2 Batterien Charger / bench 220 V for 2 batteries 14-817 Ladegerät / Tisch 110 V für 2 Batterien Charger / bench 110 V for 2 batteries VET.89

Übersicht von Zubehör : Overview for accessories : 14-830 Jacobs Dreibackenfutter bis ø 7,0 mm für Rund - und Dreikantschäfte mit Spannschlüssel Concentric Jacobs chuck up to ø 7,0 mm for round and triangular shanks with chuck key 14-842 Schnellspannfutter für Bohrdrähte von ø 0,8 mm bis ø 3,0 mm Quick-action chuck for drill wires from ø 0,8 mm up to ø 3,0 mm 14-862 Adapter für AO-Ansätze / Aesculap-Ansätze Adaptor for AO and Aesculap attachments 14-864 Adapter für DIN Ansätze Adaptor for DIN attachments VET.90

14-834 Fräseraufsatz für Acetabulum-Fräsen und Markraumbohren (100 U/min.) Chuck for acetabular and intramedullary reaming (100 r/min.) 14-836 Oszillierende Säge Standardaufnahme für Sägeblätter AO Oscillating saw standard connection for saw AO 14-811 Steriltrichter für Akku 14-810 Sterilizing funnel for battery 14-810 19E-190.01 Sterilisationsbehälter Container 14-868 Siebschaleneinsatz (2 Stück) Tray Set (2 pieces) 14-843 Hülse für Kirschnerdrähte Sleeve for Kirschner wires VET.91

14-830 Jacobs Dreibackenfutter bis ø 7,0 mm für Rund - und Dreikantschäfte mit Spannschlüssel Concentric Jacobs chuck up to ø 7,0 mm for round and triangular shanks with chuck key Drill Bits Cannulated hole ø 2.1 mm Length 150 mm (recommended) Kannulierter Bohrer Bohrung ø 2,1 mm Länge 150 mm (empfohlen) Cat. No. ø mm 1-1861 3,5 1-1862 4,0 1-1863 4,8 Drill Bits Length 150 mm (recommended) Bohrer Länge 150 mm (empfohlen) Cat. No. ø mm 1-1864 2,7 1-1865 3,5 1-1866 4,0 1-1867 4,8 Twist Drills Length 305 mm Kalibrierter Bohrer Länge 305 mm Cat. No. ø mm 1-1869 3,5 1-1870 4,0 1-1871 4,8 1-1901 Tapered Reamer, cannulated ø 15.5 mm for Femoral MFN. / DNS. - U/R Nails Kannulierter Formfräser ø 15,5 mm für Femur MFN. / DNS.- U/R Nägel 1-1906 Tapered Reamer, cannulated ø 13.5 mm for Femoral MFN. / DNS. - U/R Nails Kannulierter Formfräser ø 13,5 mm für Femur MFN. / DNS.- U/R Nägel 1-1908 Cannulated Reamer ø 9.0 mm Kannulierter Stufenfräser ø 9,0 mm VET.92

14-842 Schnellspannfutter für Bohrdrähte von ø 0,8 mm bis ø 3,0 mm Quick-action chuck for drill wires from ø 0,8 mm up to ø 3,0 mm Kirschner Wires Point Trocar Trocar Shaft End round Trocar Length 310 mm 310 mm ø 1.0 mm 7-120 7-140 ø 1.2 mm 7-121 7-141 ø 1.4 mm 7-122 7-142 ø 1.5 mm 7-123 7-143 ø 1.6 mm 7-124 7-144 ø 1.8 mm 7-126 7-145 ø 2.0 mm 7-127 7-146 ø 2.2 mm 7-128 7-147 ø 2.5 mm 7-129 7-148 ø 3.0 mm 7-130 Point Trocar Trocar Trocar Shaft End round round Trocar Length 70 mm 150 mm 150 mm ø 0.8 mm 7-200 7-250 7-280 ø 1.0 mm 7-201 7-252 7-282 ø 1.2 mm 7-254 7-284 ø 1.4 mm 7-256 7-286 ø 1.5 mm 7-208 7-258 7-288 ø 1.6 mm 7-260 7-290 ø 1.8 mm 7-262 7-292 ø 2.0 mm 7-264 7-294 ø 2.2 mm 7-266 7-296 ø 2.5 mm 7-210 7-268 7-298 ø 3.0 mm 7-270 Kirschner Wires with thread and trocar points, round end Diameter Length Threaded Length 7-310 1.6 mm 150 mm 5 mm 7-312 1.6 mm 150 mm 15 mm 7-314 2.0 mm 150 mm 15 mm 7-316 2.0 mm 200 mm 15 mm 7-318 2.5 mm 200 mm 15 mm 7-320 2.5 mm 230 mm 20 mm VET.93

14-862 Adapter für AO-Ansätze / Aesculap-Ansätze Adaptor for AO and Aesculap attachments Drill Bits ø mm AO shaft Length mm round shaft Length mm 1.1 9-010 60 / 35 9-040 45 / 30 1.5 9-012 85 / 60 9-042 70 / 55 2.0 9-014 100 / 75 9-044 85 / 70 2.5 9-016 110 / 85 9-046 95 / 80 2.7 9-018 100 / 75 9-048 85 / 70 3.2 9-020 145 / 120 9-050 130 / 115 3.2 9-021 195 / 170 9-051 180 / 165 3.5 9-022 100 / 85 9-052 95 / 80 3.5 9-023 195 / 170 9-053 180 / 165 4.5 9-026 145 / 120 9-056 130 / 115 4.5 9-027 195 / 170 9-057 180 / 165 Taps for screws ø mm AO shaft T-bar 1.5 dental 9-071 2.0 dental 9-072 2.7 9-073 9-060 3.5 thread pitch 1.25 9-074 9-062 3.5 thread pitch 1.75 9-075 9-064 4.0 thread pitch 1.75 9-076 9-065 4.5 short thread 9-077 4.5 long thread 9-078 9-068 6.5 9-079 9-070 VET.94

14-864 Adapter für DIN Ansätze Adaptor for DIN attachments Flexible Medullary Reamer (Aesculap Drive Connection DIN 58809) ø 6,0 mm 6,5 mm 7,0 mm 7,5 mm 8,0 mm 8,5 mm 9,0 mm 9,5 mm 1-1002 1-1004 1-1006 1-1008 1-1010 1-1012 1-1014 1-1016 ø 10,0 mm 10,5 mm 11,0 mm 11,5 mm 12,0 mm 12,5 mm 13,0 mm 13,5 mm 14,0 mm 1-1018 1-1020 1-1022 1-1024 1-1026 1-1028 1-1030 1-1032 1-1034 ø 14,5 mm 15,0 mm 15,5 mm 16,0 mm 16,5 mm 17,0 mm 17,5 mm 18,0 mm 1-1036 1-1038 1-1040 1-1042 1-1044 1-1046 1-1048 1-1050 VET.95

14-834 Fräseraufsatz für Acetabulum-Fräsen und Markraumbohren (100 U/min.) Chuck for acetabular and intramedullary reaming (100 r/min.) Acetabulum-Fräser-System Acetabulum Reamer System Standard AO Ansatz Fräseraufsatz mit Schnellverschluss Reamer with quick locking device 11-3440 ø 40 mm 11-3442 ø 42 mm 11-3444 ø 44 mm 11-3446 ø 46 mm 11-3448 ø 48 mm 11-3450 ø 50 mm 11-3452 ø 52 mm 11-3454 ø 54 mm 11-3456 ø 56 mm 11-3458 ø 58 mm 11-3460 ø 60 mm 11-3462 ø 62 mm 11-3464 ø 64 mm 11-3470 Acetabulumfräser: Die Fräseraufsätze werden schlüssellos mit dem Fräserschaft gekuppelt. Es ist nur ein Schaft für das Sytstem erforderlich. Acetabulum reamer: The reamer heads are coupled with shafts without a key. Only one shaft is necessary for the system. 11-3472 VET.96

SYNTHES / AO SODEM Schneidentiefe Schneidenbreite Materialdicke Schnittstärke Depth Width Material Thickness Cutting Thickness 14-2010 mm 90.0 19.05 1.27 1.37 in. 3.60 0.75 0.050 0.054 14-2012 mm 90.0 25.4 1.47 1.47 in. 3.60 1.00.058.058 14-2014 mm 90.0 25.4 1.19 1.19 in. 3.60 1.00.047.047 14-2016 mm 90.0 25.4.89 1.00 in. 3.60 1.00.035.039 14-2018 mm 90.0 25.4 1.00 1.00 in. 3.60 1.00.039.039 VET.97

Oszillierende Sägeblätter / geschränkt Oscillating Saw Blades / crossed Synthes / AO Sagital Saw Blades for Hip-Protetic SYNTHES / AO SODEM Schneidentiefe Schneidenbreite Materialdicke Schnittstärke Depth Width Material Thickness Cutting Thickness 14-2030 mm 27,0 6,0 0,4 0,6 in. 1.06 0.24 0.016 0.024 14-2034 mm 23,0 14,0 0,4 0,58 in. 0.91 0.55 0.016 0.023 14-2038 mm 48,0 14,0 0,4 0,66 in. 1.89 0.55 0.016 0.026 14-2042 mm 48,0 27,0 0,4 0,66 in. 1.89 1.06 0.016 0.026 14-2044 mm 68,0 27,0 0,6 0,81 in. 2.68 1.06 0.024 0.032 VET.98

14-836 Oszillierende Säge Standardaufnahme für Sägeblätter AO Oscillating saw standard connection for saw AO SYNTHES / AO SODEM Schneidentiefe Schneidenbreite Materialdicke Schnittstärke Depth Width Material Thickness Cutting Thickness 14-2020 mm 90.0 13.0 1.27 1.37 in. 3.60.50.050.054 14-2022 mm 90.0 13.0.89 1.00 in. 3.60.50.035.039 VET.99

Technische Daten Technical Data: VET.100

Empfohlene Basis Grundaustattung Recommended basic equipment 1 St. 14-807 Akku - Bohrmaschine mit Verschlußdeckel 1 Pcs. Battery-driven drill with closure cover 2 St. 14-810 Akku 2 Pcs. Battery 1 St. 14-814 Ladegerät / Tisch 1 Pcs. Charger / bench 1 St. 14-830 Dreibackenfutter bis ø 7,0 mm für Rund- und Dreikantschäfte mit Spannschlüssel 1 Pcs. Concentric chuck up to ø 7.0 mm for round and triangular shanks with chuck key Technische Daten für 14-807 Akku-Bohrmaschine mit Verschlußdeckel Gerätetyp: Typ BF Akku - Bohrmaschine 14-807 Spannung: Nennkapazität des Akkus 14-810: Drehzahl: Max. Drehmoment: Gewicht inkl. Akku: Motorleistung: 9,6 Volt 1,2 Ah 630 U / min 6,5 Nm 1250 Gramm 70 Watt Typ gemäß Richtlinie der EN 60601-1-2:1993 EN 60601-1:1990 + A1:1993 + A2:1995 MED.UMW Schutzart nach DIN EN 529 IP66 Technical data for 14-807 Battery-driven drill with closure cover: Equipment type: type BF Battery-driven drill 14-807 Voltage: Rated capacity of 14-810 battery: Speed: Max. torque: Weight incl. Battery: Motor output: 9,6 V 1,2 Ah 630 rev / min 6,5 Nm 1250 grams 70 W Type as per guideline of: EN 60601-1-2:1993 EN 60601-1:1990 + A1:1993 + A2:1995 MED.UMW Schutzart nach DIN EN 529 IP66 VET.101

Technische Angaben zu Akku 14-810 Akku 14-810 ist ein Ni MH (Nickelmetallhybrid) - Akku Typ: VA AA Bei normaler Belastung: 1,2 V - 1250 mah 125 ma - 16h Bei hoher Belastung: 1250 ma - 1,2 h Technical data for battery 14-810 The battery 14-810 is a Ni MH (nickel metal hydrid) battery Typ: VA AA Under normal load levels: 1,2 V - 1250 mah 125 ma - 16h With high loads: 1250 ma - 1,2 h Technische Daten zu Ladegerät 14-814 / 14-815 / 14-816 Gerätetyp: Ladegerät 14-814 / 14-815 Nennspannung: Nennfrequenz: Nennaufnahme: Nennausgangsspannung: Nennausgangsstrom: Schutzklasse Schutzart nach DIN EN 529 230 Volt / 110 Volt 50 Hz 14 VA 12 V 1100 ma max. II IPX0 Technical data for charger 14-814 / 14-815 Equipment type Charger 14-814 Rated voltage: Rated frequency: Rated input: Rated output voltage: Rated output current: Protection class: Protection type as per DIN EN 529 230 V 50 Hz 14 VA 12 V 1100 ma max. II IPX0 VET.102

Container komplett: Container complete: Contenedor completo: Contaier complet: Contenitore completo: Boden silber - Deckel nach Farbskala Bottom silvery - Lid acc. to color chart Fondo plateado - tapa según escala de colores fond argenté - Couvercle selon l'échelle de couleurs fondo argenteo - coperchio secondo scala cromatica MINI-CONTAINER Deckel gelocht - Boden ungelocht Lid perforated - Bottom non-perforated Tapa perforada - Fondo no perforado Couvercle perforé - Fond non perforé Coperchio forato - Fondo non forato Silber Gold Rot Blau Grün Silvery Golden Red Blue Green Plateado Dorado Rojo Azul Verde Argenté Doré Rouge Bleu Vert Argenteo Dorato Rosso Azzurro Verde Cat. No.: Cat. No.: Cat. No.: Cat. No.: Cat. No.: L (mm) B (mm) H (mm) 19E260.01 19E260.02 19E260.03 19E260.04 19E260.05 300 140 40 19E261.01 19E261.02 19E261.03 19E261.04 19E261.05 300 140 70 19E262.01 19E262.02 19E262.03 19E262.04 19E262.05 300 140 100 Deckel gelocht - Boden gelocht Lid perforated - Bottom perforated Tapa perforada - Fondo perforado Couvercle perforé - Fond perforé Coperchio forato - Fondo forato Silber Gold Rot Blau Grün Silvery Golden Red Blue Green Plateado Dorado Rojo Azul Verde Argenté Doré Rouge Bleu Vert Argenteo Dorato Rosso Azzurro Verde Cat. No.: Cat. No.: Cat. No.: Cat. No.: Cat. No.: L (mm) B (mm) H (mm) 19E265.01 19E265.02 19E265.03 19E265.04 19E265.05 300 140 40 19E266.01 19E266.02 19E266.03 19E266.04 19E266.05 300 140 70 19E267.01 19E267.02 19E267.03 19E267.04 19E267.05 300 140 100 Aus perforiertem Blech From Perforated Sheet Metal En tôle perforée De chapa de acero perforada In acciaio perforato 15-2150 275 x 115 x 30 mm VET.103

Container komplett: Container complete: Contenedor completo: Contaier complet: Contenitore completo: Boden silber - Deckel nach Farbskala Bottom silvery - Lid acc. to color chart Fondo plateado - tapa según escala de colores fond argenté - Couvercle selon l'échelle de couleurs fondo argenteo - coperchio secondo scala cromatica Deckel gelocht - Boden gelocht Lid perforated - Bottom perforated Tapa perforada - Fondo perforado Couvercle perforé - Fond perforé Coperchio forato - Fondo forato Silber Silvery Plateado Argenté Argenteo Cat. No.: L (mm) B (mm) H (mm) 19E-275.01 310 190 40 19E-276.01 310 190 65 19E-277.01 310 190 130 Aus perforiertem Blech From Perforated Sheet Metal En tôle perforée De chapa de acero perforada In acciaio perforato 15-2200 275 x 170 x 30 mm VET.104

The new wire baskets Die neuen Siebkörbe Hoher Bedienungskomfort durch geringes Gewicht der Siebkörbe Engmaschige Seitenwände verhindern das ausbrechen von feinen Instrumentenspitzen bei der Aufbereitung und Transport der Siebe. Für jede Siebkorbgröße ist ein Deckel verfügbar. Dadurch ist ein besonderer Schutz feiner Instrumente (Mikro, HNO) bei Aufbereitung, Transport und Lagerung gegeben. Die neuen Siebkörbe sind in allen üblichen Größen verfügbar. Tragegriffe an den Siebkorbdeckeln erleichtern den Transport und die Entnahme aus einem Sterilcontainer. Glatte Oberflächen zur Vermeidung von Verletzungen und Beschädigungen der OP-Handschuhe. Die Deckel lassen sich beidseitig an den Siebkörben ansetzen, der Deckelverschluss ist einfach zu handhaben. Stabile Kunststoff-Füße garantieren einen sicheren Stand und eine optimale Stapelbarkeit der Siebkörbe. Deckel Lid 15-3054 540 x 255 mm 15-3056 405 x 255 mm 15-3058 255 x 245 mm Cat. No.: L x B x H 15-3060 540 x 255 x 30 mm 15-3061 540 x 255 x 50 mm 15-3062 540 x 255 x 70 mm 15-3063 540 x 255 x 100 mm Cat. No.: L x B x H 15-3066 405 x 255 x 30 mm 15-3067 405 x 255 x 50 mm 15-3068 405 x 255 x 70 mm 15-3069 405 x 255 x 100 mm Cat. No.: L x B x H 15-3072 255 x 245 x 30 mm 15-3073 255 x 245 x 50 mm 15-3074 255 x 245 x 70 mm 15-3075 255 x 245 x 100 mm High operational comfort owing to reduces weight of wire baskets. Close-meshed sides avoid breaking of tips of delicate instruments during processing and transport of wire basket. Lids are available for each size of wire baskets, which provides a special protection of delicate instruments, such as Micro and ENT instruments, during processing, transport and storing. Handles of lids make transportation and removal from containers easier. Lids can easily be fixed to both sides to the wire basket. Locks of lids are easily to be handled. Sturdy footrests guarantee a secure hold and an optimum stacking of wire basket. These wire baskets have a smooth surface to avoid injuries and damages of surgical gloves. The new wire basket are available in all customary sizes. VET.105

T 321 Alu Case (without racks) T 310 T 311 T 312 T 313 T 314 T 315 T 316 T 317 Rack for ø 1.5 mm screws Rack for ø 2.0 mm screws Rack for ø 2.7 mm screws Rack for ø 3.5 mm 1.25 pitch screws Rack for ø 3.5 mm 1.75 pitch screws Rack for ø 4.0 mm screws (half threaded) Rack for ø 4.0 mm screws (full threaded) Rack for ø 4.5 mm screws 3-530 Measuring Gauge for Screws VET.106

Deckel und Wanne perforiert Lid and Bottom perforated 19E-290.01 250 x 60 x 50 (L x B x H) 19E-291.01 450 x 70 x 70 (L x B x H) VET.107

Abmessungen Measurements 290 x 80 x 52 mm 460 x 80 x 52 mm 670 x 80 x 52 mm für 1 Optik for 1 Telescope 19E-295.01 19E-295.02 19E-295.03 für 2 Optiken for 2 Telescopes 19E-296.01 19E-296.02 VET.108

Tücher Drape Filterpapierspender Filter Dispenser Filterhalterung Filter Holder 19E-351.01 für Papierfilter for paper filter 19E-351.02 für Textilfilter for textile filter 19E-350.00 Abmessungen Measurements 60 x 40 cm 65 x 65 cm 85 x 85 cm 90 x 60 cm 90 x 80 cm 130 x 45 cm 130 x 60 cm 140 x 100 cm 185 x 45 cm 185 x 60 cm Katalog Nummer Catalog Nunmer 19E-137.01 19E-137.02 19E-137.03 19E-137.04 19E-137.05 19E-137.06 19E-137.07 19E-137.08 19E-137.09 19E-137.10 Kennzeichnungsschilder Identification Lables Veterinär Silber / Silver Gold / Gold Rot / Red Blau / Blue Grün / Green Anthrazit / Dark Grey Kennzeichnungsschilder, Text bis zu 16 Stellen Identification Lables, engraved max. 16 letters 19E-352.01 19E-352.02 19E-352.03 19E-352.04 19E-352.05 19E-352.06 Kennzeichnungsschilder, unbeschriftet Identification Lables, not engraved 19E-353.01 19E-353.02 19E-353.03 19E-353.04 19E-353.05 19E-353.06 Sortier-Magazin für Kennzeichnungsschilder Dispenser for Identification Lables 19E-354.00 VET.109

Haltestifte Holding Pins 19E-355.01 für Drahtkörbe for wire baskets 19E-355.02 für Trennbleche for partition sheets Trennbleche Partition Sheets Abmessungen Measurements 50 x 20 mm 130 x 20 mm 225 x 20 mm 460 x 20 mm Katalog Nummer Catalog Nunmer 19E-356.01 19E-356.02 19E-356.03 19E-356.04 Gleitschieber Divider 19E-357.00 Schienen für Gleitschieber Sliding Rails for Divider 19E-358.01 19E-358.02 232 mm 471 mm Anschlagrahmen Limiting Bars 19E-359.01 19E-359.02 232 mm 471 mm Spiralfeder-Haltevorrichtung Spiral Holding 19E-360.01 19E-360.02 einfach / single doppelt / double VET.110

Fixierklammer Fixation Clamp 19E-361.00 Einmal-Papierfilter Disposable Paper Filters Packung 100 Stk. 100 Pcs. / Package 19E-370.01 für 1/1, 3/4 und 1/2 - Container for 1/1, 3/4 and 1/2 - Containers 19E-370.02 19E-370.03 für Mini-Container for Mini Containers für Dental-Container for Dental Containers Langzeit Textilfilter Textile Filters 19E-371.01 für 1/1, 3/4 und 1/2 - Container for 1/1, 3/4 and 1/2 - Containers 19E-371.02 19E-371.03 für Mini-Container for Mini Containers für Dental-Container for Dental Containers VET.111

Indikatorschilder Paper Label with Indicator Packung 100 Stk. 100 Pcs. / Package 19E-372.01 für 1/1, 3/4 und 1/2 - Container for 1/1, 3/4 and 1/2 - Containers 19E-370.02 für Mini und Dental Container for Mini and Dental Containers Plombe Plastic Security Seal Packung 1000 Stk. 1000 Pcs. / Package Verschlußsiegel Security Seal Packung 1000 Stk. 1000 Pcs. / Package 19E-373.01 19E-374.01 Verschlußetiketten Seal Label Packung 1000 Stk. 1000 Pcs. / Package 118 x 39 mm 19E-374.02 19E-374.03 selbstklebend self-adhesive VET.112

Instrumentenpflegeöl Oil for Instrument Care 19E-380.01 400 ml für chirurgische Instrumente for surgical instruments 19E-380.02 50 ml für Druckluftmaschinen und sterilisierbare Motorsysteme for air-driven machineries and sterilizable motor-systems 19E-381.01 1000 ml für chirurgische Instrumente for surgical instruments 19E-381.02 400 ml PE Pumpsprayflasche für 19E-381.01 (ohne Inhalt) PE Pumpspray-Bottle for 19E-381.01 (unfilled) VET.113

Bürsten Spender Brush Dispensers für 20 Bürsten for 20 brushes Silber / Silver Gold / Gold Rot / Red Blau / Blue Grün / Green 285 x 280 x 85 mm 19E-400.01 19E-400.02 19E-400.03 19E-400.04 19E-400.05 Bürsten Brushes 19E-405.00 VET.114

Wagen Trolley 19E-420.00 720 x 620 x 800 mm 19E-421.00 1030 x 620 x 1170 mm VET.115

Sterilisierzangen Sterilizing Forceps 19E-005 Cheattle 27 cm, 101/2 19E-006 30 cm, 12 Sterilisierklammeren Sterilizing Clamps 19E-017 Bunt 10,5 cm, 4 19E-018 Mayo 14,5 cm, 51/2 19E-019 Mayo 14,5 cm, 51/2 VET.116

Instrumentenkästen Instrument Boxes Art. Nr. Art. No. 19E-021.01 19E-021.02 19E-021.03 19E-021.04 19E-021.05 L x B x H l x w x h 165 x 90 x 35 mm 200 x 100 x 50 mm 220 x 150 x 50 mm 260 x 150 x 50 mm 305 x 205 x 50 mm Schalen Trays Art. Nr. Art. No. 19E-022.01 19E-022.02 19E-022.03 19E-022.04 19E-022.05 19E-022.06 19E-022.07 L x B x H l x w x h 210 x 160 x 10 mm 240 x 180 x 10 mm 310 x 150 x 10 mm 310 x 210 x 10 mm 350 x 240 x 10 mm 400 x 270 x 10 mm 420 x 280 x 10 mm Art. Nr. Art. No. 19E-023.01 19E-023.02 19E-023.03 19E-023.04 19E-023.05 L x B x H l x w x h 230 x 155 x 30 mm 300 x 175 x 30 mm 300 x 175 x 40 mm 350 x 240 x 36 mm 400 x 300 x 50 mm VET.117

astandgefäße Jars Art. Nr. Art. No. 19E-024.01 19E-024.02 19E-024.03 19E-024.04 19E-024.05 19E-024.06 19E-024.07 Ø x H Ø x h 30 x 90 mm 50 x 100 mm 50 x 130 mm 50 x 175 mm 75 x 100 mm 75 x 130 mm 75 x 175 mm Spülschalen Solution Bowls Art. Nr. Art. No. 19E-025.01 19E-025.02 19E-025.03 19E-025.04 19E-025.05 19E-025.06 19E-025.07 19E-025.08 19E-025.09 19E-025.10 Liter litres 0,75 1,00 2,00 2,50 3,00 4,50 6,00 6,00 8,50 11,00 Ø x H Ø x h 165 x 60 mm 175 x 70 mm 220 x 80 mm 225 x 90 mm 240 x 110 mm 275 x 115 mm 290 x 125 mm 310 x 120 mm 345 x 125 mm 380 x 130 mm Art. Nr. Art. No. 19E-026.01 19E-026.02 19E-026.03 19E-026.04 19E-026.05 19E-026.06 Liter litres 0,05 0,07 0,14 0,35 0,45 0,70 Ø x H Ø x h 40 x 19 mm 61 x 30 mm 80 x 40 mm 116 x 50 mm 128 x 55 mm 147 x 65 mm VET.118

Messbecher Measures Art. Nr. Art. No. 19E-027.01 19E-027.02 19E-027.03 19E-027.04 Liter litres 0,25 0,50 1,00 2,00 Nierenschalen Kidney Bowls Art. Nr. Art. No. 19E-028.01 19E-028.02 19E-028.03 Liter litres 0,170 0,250 0,275 VET.119

Nadel-Sterilisierdosen Needle Sterilizing Boxes 19E-029.00 komplett complete 19E-029.01 Innendose, allein Insert, only 19E-030.01 19E-030.02 19E-030.03 50 x 25 x 4,5 mm 65 x 42 x 8,0 mm 75 x 25 x 4,5 mm 19E-031.00 150 x 95 x 13 mm 19E-032.00 Sauerbruch 210 x 125 x 17 mm VET.120

VET.121

Oscillotronic 500 500 Watt Leistung 6500 bis 24000 Schwingungen, stufenlos regelbar Vollautomatische Lastkompensation über den gesamten Schwingungsbereich, d. h. eine eingestellte Schwingung bleibt über den gesamten Lastbereich erhalten Schlanke Motorausführung mit sehr ruhigem Lauf ca. 52 77 db(a) in Abhängigkeit der eingestellten Schwingung Modernste Motorelektronik mit diversen Sicherheits- und Schutzfunktionen Sanftanlauf beim Einschalten, vermindert Unfallgefahr und schont alle mechanischen und elektronischen Bauteile Robuste Konstruktion für höchste Belastbarkeit im Dauerbertrieb Sicherheits-EIN-AUS-Schalter Gewicht nur 1,25 kg ohne Kabel (1,5 kg mit Kabel) Vibrations- und Wartungsarm 1 Jahr Garantie auf Motor und Antriebseinheit (bei sachgerechter Behandlung), 2 Jahre Gewährleistung Regelung außerhalb des Handbereiches, dadurch keine unbeabsichtigte Verstellung der eingestellten Schwingung 5 Meter Euroflachsteckerkabel bei der 230 Volt Version oder 3 Meter USA-Steckerkabel bei der 110 Volt Version Spezielle Motorlagerung (Gipsstaubgeschützt) und verstärkte Ankerwelle Doppelschutzisoliert, Motor entspricht Schutzklasse II und medizinischer Anwendungsteil entspricht Typ BF Bild- und Tonfunkentstört CE-Konform Geprüft nach EN 60601-1, EN 60601-1-2, IEC 60601-1, IEC 60601-1-2 500 Watt power 6500 to 24000 oscillations, steplessly adjustable Full-automatic power-compensation, i.e. a once chosen oscillation stays during the whole powercompensation Slender motor body with a silent operation running, 52 77 db(a) in relation to the selected oscillations Latest electronic system with various protection and security functions Gently slow starting prevents accidents and treats all mechanical and electronic parts with care Strong construction for highest stress at non-stop operation Safety ON / OFF switch Weight only 1,25 kg without cable (1,5 kg with cable) Vibration-free and low-maintenance The regulation of the motor performance is on the rear of the motor and therefore won t disturb the user during his work. Once selected the oscillations will remain constant. 5 meter cable with EU-connection, 230 Volt version or 3 meter cable with US-connection, 110 Volt version Special positioning of the motor, protected from plaster dust Double protection isolation, motor according to class II, medical use of type BF Free from interference CE conformity Approved according EN 60601-1, EN 60601-1-2, IEC 60601-1, IEC60601-1-2 VET.122

Technische Daten Technical Data 110 Volt 110 Volt 110 V ~, 60 Hz 110 V ~, 60 Hz Leistung 500 W Power 500 W 6.500 24.000 Schwingungen / min 6.500 24.000 oscillations / min Stufenlos regelbar steplessly adjustable 3 Meter USA-Steckerkabel 3 meter cable with USA-plug 230 Volt 230 Volt 230 V ~, 50 Hz 230 V ~, 50 Hz Leistung 500 W Power 500 W 6.500 24.000 Schwingungen / min 6.500 24.000 oscillations / min Stufenlos regelbar steplessly adjustable 5 Meter Euroflachsteckerkabel 5 meter cable with EURO-plug Gipssäge, komplett mit Zubehör: Plaster-Saw, complete with Accessories: + 1 Sägeblatt Ø 50 mm + 1 Saw Blade Ø 50 mm + 1 Sägeblatt Ø 65 mm + 1 Saw Blade Ø 65 mm + 1 Paar Gabelschlüssel + 1 Pair of Wrenches + Kabel + Cable 17E-035.11 110 Volt, 500 Watt 17E-035.23 230 Volt, 500 Watt 17E-036.11 mit Koffer / with Case 17E-036.23 mit Koffer / with Case Gipssäge, für synthetischen Gips Plaster-Saw, for syntetic Plaster komplett mit Zubehör: complete with Accessories: + 1 Sägeblatt Ø 50 mm + 1 Saw Blade Ø 50 mm + 1 Sägeblatt Ø 65 mm + 1 Saw Blade Ø 65 mm + 1 Paar Gabelschlüssel + 1 Pair of Wrenches + Kabel + Cabel 17E-037.11 110 Volt, 500 Watt 17E-037.23 230 Volt, 500 Watt 17E-038.11 mit Koffer / with Case 17E-038.23 mit Koffer / with Case VET.123

17E-040.50 Sägeblatt für normalen Gips 17E-040.50 Saw Blade for normal Plaster 17E-041.50 Sägeblatt für sythetischen Gips 17E-041.50 Saw Blade for synthetic Plaster 17E-040.65 Sägeblatt für normalen Gips 17E-040.65 Saw Blade for normal Plaster 17E-041.65 Sägeblatt für sythetischen Gips 17E-041.65 Saw Blade for synthetic Plaster 17E-050.01 Sägeblatt für normalen Gips 17E-050.01 Saw Blade for normal Plaster 17E-051.01 Sägeblatt für sythetischen Gips 17E-051.01 Saw Blade for synthetic Plaster VET.124

17E-050.02 Sägeblatt für normalen Gips 17E-050.02 Saw Blade for normal Plaster 17E-051.02 Sägeblatt für sythetischen Gips 17E-051.02 Saw Blade for synthetic Plaster 17E-050.03 Sägeblatt für normalen Gips 17E-050.03 Saw Blade for normal Plaster 17E-051.03 Sägeblatt für sythetischen Gips 17E-051.03 Saw Blade for synthetic Plaster 17E-055.00 Begrenzungsscheibe 17E-055.00 Distance disk 17E-057.00 Sägeblatt für Stryker 17E-057.00 Saw Blade for Stryker VET.125

17E-060.50 Sägeblatt für normalen Gips 17E-060.50 Saw Blade for normal Plaster 17E-061.50 Sägeblatt für sythetischen Gips 17E-061.50 Saw Blade for synthetic Plaster 17E-060.65 Sägeblatt für normalen Gips 17E-060.65 Saw Blade for normal Plaster 17E-061.65 Sägeblatt für sythetischen Gips 17E-061.65 Saw Blade for synthetic Plaster 17E-065.01 Sägeblatt für normalen Gips 17E-065.01 Saw Blade for normal Plaster 17E-066.01 Sägeblatt für sythetischen Gips 17E-066.01 Saw Blade for synthetic Plaster VET.126

17E-065.02 Sägeblatt für normalen Gips 17E-065.02 Saw Blade for normal Plaster 17E-066.02 Sägeblatt für sythetischen Gips 17E-066.02 Saw Blade for synthetic Plaster 17E-065.03 Sägeblatt für normalen Gips 17E-065.03 Saw Blade for normal Plaster 17E-066.03 Sägeblatt für sythetischen Gips 17E-066.03 Saw Blade for synthetic Plaster VET.127

Plaster Instruments for fingers 10-1072 Knowles 14,0 cm 10-1074 Lister Exentric 19,0 cm 10-1076 Lorenz 23,0cm 21E-087 20,0 cm VET.128

Plaster Instruments Lister 21E-076 14,0 cm 21E-078 18,0 cm 21E-079 20,0 cm 10-1086 Bergmann 23,0 cm Smith Mod USA 10-1088 18,0 cm 10-1090 20,0 cm 10-1092 23,0 cm VET.129

Technische Änderungen vorbehalten Technical features are subject to change Cambios técnicos reservados Ci riservaiamo il diritto di modifiche tecniche erbrich - instrumente GmbH Eugenstr. 33 D-78532 Tuttlingen Tel.: +49 74 61 / 96 57 30 Fax: +49 74 61 / 9657 320 E-mail:erbrich-instruments@t-online.de Website: www.erbrich-instruments.com Copyright 2003 erbrich-instrumente GmbH VET/10/03 VET.130