Side 1 Oversikt for aggregat nr: 1 Aggregatstørrelse 06 Aggregatbredde 1000 mm Vekt 350 kg Topvex aggregater er bygget med integreret automatikk - baseret på Systemair regulatorer Tilluft Fraluft Luftmengde (1,205 kg/m³) 2000.00 m3/h 2000.00 m3/h Lufthastighet i aggregat 1.74 m/s 2.22 m/s Eksternt trykktap 250 Pa 250 Pa Filter F7 F5 Vifte 59 % 63 % 2072 o/min 1975 o/min SFP, rene filtre 1.79 kw/(m³/s) Varmeveksler 80.1 % Varmebatteri 4.82 kw - Luft 14.6/22.0 C - Vann 55/35 C - 2.2 kpa - 0.06 l/s Rørtilkobling 1/2" / 1/2" Lydeffektnivå 63 125 250 500 1k 2k 4k 8k Hz Total Tilluft, innblåsning 84 79 83 77 73 71 66 62 db 80 db(a) Uteluft, inntak 80 77 75 66 57 53 51 54 db 69 db(a) Fraluft, avkast 79 76 79 76 73 68 61 54 db 78 db(a) Fraluft, avtrekk 74 74 74 61 56 52 46 39 db 67 db(a) Lyd, omgivelser 65 66 66 57 52 49 44 39 db 61 db(a) Lydeffektnivå, kun tilluft 64 66 64 55 48 47 44 39 db 59 db(a)
Side 2 Plantegning Inspeksjonsside Nødvendig inspeksjonsområde for åpne dører: 830, 900
Side 3 Plantegning
Side 4 Teknisk spesifikasjon Automatikk Sprog i controler menu Temperaturstyring Luftmengdestyring Ekstern kommunikasjon Batteri konfiguration English Kaskade utelufttempertur-regulering Konstant kanaltryk Modbus via RS-485, EXOline via TCP/IP (Innebygget webserver) Varmebatteri Hovedtilførsel til automatikken Spenning 3x400V Anbefalt sikring 3 x 10 A Tilluftsaggregat består av Filter Dimensjonerende trykkfall 122 Pa Start trykkfall/slutt trykkfall 60/185 Pa Filterklasse F7 Filterstørrelse 903x385 Filterlengde 375 mm Roterende varmeveksler Tilluft Avtrekk Luftmengde 2000 2000 m3/h Trykkfall 79 100 Pa VINTER Lufttemperatur, vinter før/etter -15.0/14.6 22.0/-6.2 C Relativ luftfuktighet, vinter før/etter 60/28 30/95 % Temperaturvirkningsgrad 80.1 % Varmegjenvinner type Temperaturvirkningsgrad Drivsystem for rotor Elektriske data Temperaturvarmeveksler Standard effektiv Konstant drift 1x230V, 25W, 0.32Amp Kammervifte, Kammer Direkte drift Viftetype Høyeffekt Luftmengde 2000 m3/h Statisk trykk, vifte 559 Pa Eksternt trykktap 250 Pa Viftehastighet 2072 o/min Vifte virkningsgrad 59 % Hovedstrømforsyning 3x400 V Motor Termosikring Termistor Effektforbruk fra hovedtilførsel, inkl frekvensomformer 0.53 kw
Side 5 El-forbruk inkluderer frekvensomformere 0.53 kw Høyeffekt vannvarme, Væske Varmebatteri vann leveres separat og monteres på plass, plug-in. Luftmengde 2000 m3/h Trykkfall 19 Pa Lufttemperatur, inn/ut 14.6/22.0 C Effekt 4.82 kw Væskemedie Vann Væsketemperatur inn/ut 55.0/35.0 C Væskemengde 0.058 l/s Væske trykktap 2.2 kpa Væskehastighet 0.42 m/s Batterivolum 0.7 l Anslutningsside Service side Tilkoblingsmål inn/ut 1/2" / 1/2" Rørmateriale Cu Lamellmateriale Al Lamellavstand 2.0 mm Rørrader 1 Batteri type 6.30.CU.10.AL.11.01.0765.20.W.X.X.002.011.R 1/2" Fraluftsaggregat består av Filter Dimensjonerende trykkfall 90 Pa Start trykkfall/slutt trykkfall 29/150 Pa Filterklasse F5 Filterstørrelse 903x320 Filterlengde 600 mm Roterende varmeveksler Data vises på tilluft Kammervifte, Kammer Direkte drift Viftetype Høyeffekt Luftmengde 2000 m3/h Statisk trykk, vifte 528 Pa Eksternt trykktap 250 Pa Viftehastighet 1975 o/min Vifte virkningsgrad 63 % Hovedstrømforsyning 3x400 V Motor Termosikring Termistor Effektforbruk fra hovedtilførsel, inkl frekvensomformer 0.47 kw El-forbruk inkluderer frekvensomformere 0.47 kw
Side 6 Andre komponenter
Side 7 Systemair E28 integrated control system Topvex air handling units are built with a complete and fully integrated control system. Before shipment the unit has been assembled and passed a final functional test and inspection. Flyt Skjema Friskluft Avkast Avtrekk Tilluft Tilbehør til aggregat uten varmebatteri. Batteri leveres separat UC Aggregatstyring SS Temperaturføler, tilluft HE Varmeveksler SF Tilluftsvifte OS Temperaturføler, uteluft RC Rotorstyring EF Avtrekksvifte ETS Temperaturføler, avtrekk RM Rotormotor PTS Trykkføler tilluftsvifte EHS Avkast temperaturføler PTE Trykkføler avtrekksvifte HT Varmebatteri FGS Filtervakt, tilluft WHB Varmtvannsbatteri FGE Filtervakt, avtrekk FPS Frostføler Switchboard and mains supply The switchboard with terminal blocks, relays, fuses, 24 V AC power supply and controller. Mains power supply is to be connected directly in the main switchboard and cables for external components in the main switchboard or in terminal boxes at the gable of the unit. The unit should be permanently connected to the mains electric supply through a lockable safety switch. The safety switch is not mounted from the factory but delivered with the unit. Controller and hand terminal The controller is installed in the switchboard, and the programming and normal handling is carried out from a separate cable-connected (10m) hand terminal with display and buttons - the Systemair Control Panel - the SCP. The protection class of the hand terminal is IP 41. Schedules The regulator has individual schedules for start, stop and air flow rate for each week-day as well as schedules for holidays. The regulator has an automatic summer-winter-time change over. Outside normal operating hours free cooling is available according to settings. Variable Air Volume (VAV) control through constant pressure in ducts The air pressure of supply and extract air are controlled separately. The supply, extract, high and low air pressure in Pa is set separately on the hand terminal. The total air pressures are measured by pressure transducers in the supply air duct and in the extract air duct. A PI-regulator maintains the set point value by controlling the speed of the fans.
Side 8 Access rights - passwords There are 3 different log-on levels - Basic level (no password) - read-only access to all settings and parameters - Operator level (password) - read/write access to all settings and parameters, but no access right to the configuration of the system - Administrator level which has the highest authority (special password) - full read/write access to all settings and parameters (also configuration of the whole system) Alarms and safety functions If an alarm condition occurs, the Alarm LED on the hand terminal will flash. The LED will continue to flash as long as there are unacknowledged alarms. Alarms are logged in the alarm list. The list shows the type of alarm, date and time for the alarm and alarm class - A, B or C: - Alarm type A will stop the fans and close the dampers or switch the unit to a special mode according to the configuration - Alarm type B is only to inform the users about a failure, and the unit is still running as well as possible - Alarm type C - only to inform the user that the unit has been switched away from automatic running mode to manual control If water heater is used then for frost protection a temperature sensor is installed in a return circuit of the coil. The control signal to the mixing valve is kept at a level that secures that water return temperature at all times is held at a factory set minimum. This protection is also active when the unit is not running. This extended system offers the maximum of protection safety. If the water temperature is getting too low anyway the unit including fans is shut down. Flexible System A skilled service technician - on the site and on the demand from the user - will be able to adapt the regulation further to the requirements of the users; - The air flow can be adaptable to the CO2 concentration for CAV air flow regulation as well as for VAV air flow regulation - The temperature control mode can be changed. - In addition to the fixed schedule an external start signal for extended operation is available. - In addition or as an alternative to the fixed schedule an external start/stop input signal is available. - A large number of other alternative functions are optional. Modbus via RS 485, EXO line via TCP/IP (built-in WEB) The controller is prepared for communication via RS485 communication port to a MODBUS based BMS system (Building Management System). The controller can work as a stand-alone system without any support from other controllers.