Polyesterklebemørtel til montasje i massivstein, hulstein, lettklinkerbetong og betong. Inneholder ikke styren og epoksy. EGENSKAPER ETA-13/0415, UK-DoP-e13/0415, FDS- POLYGP(1.1)UK, FDS-POLYGP(1.1)DK Materiale Polyesterlim uten styren Brukes med gjengestang LMAS i galvanisert stål eller rustfritt stål A4-70 Fordeler Rask fastgjøring: sparer tid for brukeren Spenningsfri fastgjøring Reduserte kant- og ankeravstander Mulig å bruke innendørs Meget holdbar fastgjøring Forsegler hullet Lav MAL-kode ANVENDELSE Skjøter Murstein Porebetong Lettklinkerbetong Bruksområder Stål og metallkonstruksjoner Skinnesystemer, lagerreoler Maskiner, sanitær Oppheng av klimaanlegg og vannvarmere Antenner Markiser Fasadekledning 1/5
TEKNISK DATA Item codes Innhold [ml] Vekt [kg] Packaging [Cartouches] POLY-GP300-FR Beige 300 0.6 12 POLY-GP300G-FR Gris 300 0.6 12 POLY-GP380-FR Beige 380 0.9 12 Two nozzles are supplied with each cartridge. Downloadable Safety Data Sheet available from www.strongtie.eu Performance values (Service loads) Tension [Rds,N] [kn] Shear [Rds,V] [kn] Autoclaved Autoclaved aerated Hollow aerated Hollow Solid Brick Hollow Brick Solid Brick Hollow Brick concrete concrete block concrete concrete block blocks blocks Poly GP + LMAS M8 0.72 0.26 0.43 0.26 0.72 0.26 0.43 0.26 Poly GP + LMAS M10 0.72 0.35 0.43 0.35 0.72 0.35 0.43 0.35 Poly GP + LMAS M12 0.72 0.35 0.57 0.35 0.72 0.35 0.57 0.35 1) Performance values are calculated from published data characteristic values in the ETA on which partial safety factors from ETA and a partial coefficient = 1.4 #f actions are applied. Service charges include the sealing position in the holder and is adhered to the method of installation. For hollow brackets unknown resistance, site of trials are needed (in accordance with ICASA recommendations for use by construction professionals for the construction of ankles tests on site). 2/5
MONTERING Herdetid Underlagstemperatur [ C] Bearbeidingstid Herdetid Bor hullet Rengjør hullet med stålbørste og blåsepumpe (blås 5x, børst 4x og blås 5x) Sett inn en hylse OBS: Trykk først ut klebemørtelen til den får en jevn farge. Trykk deretter inn mørtel i hullet Sett inn gjengestangen forsiktig med en roterende bevegelse, og la klebemørtelen herde Skru fast emnet Bor hullet Rengjør hullet med stålbørste og blåsepumpe (blås 5x, børst 4x og blås 5x) Fyll opp hullet 1/2-2/3 med klebemørtel ved å pumpe fra bunnen og ut Sett inn LMASankeret med en roterende bevegelse og la mørtelen tørke Sett på emnet og spenn det fast med en kalibrert momentnøkkel Solid Brick Installation 3/5
Ø drilling [d0] of hole in the fixture [df] Dybde på [h1] Size [Sw] Tilspenningsmoment Effektiv [Tinst] settedybde [Nm] [hef] spacing - Scr,N spacing - Smin - Ccr,N Poly GP + LMAS M8 10 9 85 13 4 80 160 50 80 50 Poly GP + LMAS M10 12 12 85 15 6 80 200 50 100 50 Poly GP + LMAS M12 14 14 85 18 8 80 240 50 120 50 Cellular Concrete - Cmin Ø drilling [d0] of hole in the fixture [df] Dybde på [h1] Size [Sw] Tilspenningsmoment Effektiv [Tinst] settedybde [Nm] [hef] spacing - Scr,N [Nm] spacing - Smin - Ccr,N Poly GP + LMAS M8 10 9 85 13 2 80 160 50 80 50 Poly GP + LMAS M10 12 12 85 15 3 80 200 50 100 50 Poly GP + LMAS M12 14 14 85 18 5 80 240 50 120 50 Foundation Brick Installation - Cmin Bore Size of the Sieve [d0] of hole in the fixture [df] Dybde på [h1] Size [Sw] Installation Effektiv Torque settedybde spacing spacing [Tinst] [hef] - Scr,N - Smin - Ccr,N - Cmin [Nm] Poly GP + LMAS M8 16 16x85 ou 16x130 9 135 13 4 130 500 100 250 100 Poly GP + LMAS M10 16 16x85 ou 16x130 12 135 15 6 130 500 100 250 100 Poly GP + LMAS M12 16 16x85 ou 16x130 14 135 18 6 130 500 100 250 100 Hollow Cinderblock installation 4/5
Bore Size of the Sieve [d0] of hole in the fixture [df] Dybde på [h1] Effektiv Tilspenningsmoment settedybde spacing spacing Size [Tinst] [hef] - Scr,N - Smin [Sw] [Nm] - Ccr,N - Cmin Poly GP + LMAS M8 16 16x130 9 135 13 4 130 500 100 250 100 Poly GP + LMAS M10 16 16x130 12 135 15 6 130 500 100 250 100 Poly GP + LMAS M12 16 16x130 14 135 18 6 130 500 100 250 100 5/5